LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
*Irradiance And Dosage Sensors
-
This sensor family provides cosine corrected irradiance measurement in W/cm² and dosage measurement in J/cm². The sensors are calibrated over their entire spectral range, and are thus ideal for irradiance and dosage measurement of UV, VIS and IR LED based light sources
-
Product
16 Channel Input/Output Register
V977
-
The Mod. V977 is a 1-unit wide VME module that can work either as 16 channel general purpose I/O Register or as Multihit Pattern Unit; the operating mode is selected via VME and is signalled via front panel LEDs.
-
Product
Dynamite Source Controller
BOOM BOX III
-
*Easy to Use, just hold the Arm and Charge toggles, Unit charges and is ready to fire*Web based interface allows easy setup and storage of data on PC, Tablet, or Cell phone*Shooter updated with easy to read graphical display and status LEDs*Same unit used for Encoder and Decoder modes
-
Product
AGC, SNMP, RFoG FTTB Optical receiver
RFoG4002, RFoG4004
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai RFoG4002 ( two-port ), RFoG4004 ( four-port ), is a type of high-grade AGC, Network management, RFoG FTTB outdoor optical receiver. Various operating parameters of machine are microprocessor-controlled, LED display. Through the keys of machine can adjust and set EQ、ATT. Optional network transponder, implement remote network management. Large dynamic range of optical AGC characteristics, RFoG4002 ( two-port ), RFoG4004 ( four-port ) high output ,for FTTC, FTTN fiber access network. As a unit of CATV network RX, is a high performance, highly flexible, cost-effective CATV optical receiver.
-
Product
Incoherent Sources
-
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Metal Wire Torsion Testing Machine
WTT Series
-
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
-
Product
Integrating Sphere Systems
-
An optical device for various purposes such as. measuring the radiant flux (optical power) from a laser diode, light-emitting diode (LED) or bulb.
-
Product
4U CompactPCI Hybrid PlusIO System with 5 CompactPCI and 4 CPCI-S.0 Peripheral Slots
cPCIS-P2630R
Backplane
- 3U CompactPCI PlusIO backplane with five CompactPCI and four CPCI-S.0 peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for CompactPCI 50mm depth RTMs- Hot-swappable cooling fans & filter- 400 W ATX Power supply
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
Chassis - up to 8 8x1 Modules, 16 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration for up to 64 Relay Drives
CXM/64-MF
Chassis
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
LXI 24-Channel 1GHz Video Multiplexer
60-721A-001
Multiplexer Module
This High Performance Video MUX is designed for the switching of RF signals in 75Ω systems at frequencies up to 1GHz. It is ideal for 75Ω monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment. The automatic connection of unused channels into 75Ω terminations helps maintain signal integrity and minimizes the possibility of introducing unwanted responses. The common connection is also automatically terminated into 75 Ohm when unused. Front panel LED indicators adjacent to each multiplexer input connector provide an easy visual identification of the active channel.
-
Product
7"/10.1"/12.1"/15"/15.6"/17"/18.5"/19"/21.5"/23.8"/27"/32"/43" Open Frame Industrial Touch Monitor
OM Series
Industrial Monitor
- 7"/12.1"/15"/17"/19" (Fullscreen) LCD panel with LED backlight with up to 50,000 service life- 10.1"/15.6"/18.5"/21.5"/23.8"/27"/32"/43" (Widescreen) LCD panel with LED backlight with up to 50,000 service life- 10-point PCAP touchscreen (glove-use available)- Anti-fingerprint surface treatment for ease of cleaning and enhanced readability- Wide viewing angles support both portrait and landscape modes- IP 65 rating for water and dust protection- Value-added service (flexible customization)- Panel/ VESA/ Desktop Stand
-
Product
Differential Pressure Meters
-
These differential pressure meters contain many characteristics that can be found i Differential Pressure Meters for measuring differential pressures of gases and liquids in the industrial sector, in medical engineering and meteorologyn modern measuring instruments such as data hold function, LCD or LED display, internal memory and the ability to transfer data to a computer and software for processing measurement values. Some models come with an analogue output.
-
Product
Precession Magnetometers
Proton
-
GEM offers the most advanced Proton Precession magnetometers available on the market today. Advanced Research and Development, and the release of the v7.0 version have led to a system that delivers the latest technology combined with the classic value of a standard Proton Precession type of system
-
Product
Video Signal Distributor
MSHM-305A/310A
-
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
Product
6-24V LED Heavy Duty Circuit Tester
1646
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. Quickly and safely test high and low voltages on all vehicle voltages, including computerized engine. High impedance to protect sensitive electronic sensors, microprocessors, electronic ignition components and air bags.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI Card
LPCIe-7250
Relay
LPCIe-7250 provides 8-CH SPDT (Form C) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are non-polarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments.
-
Product
LED based light source
iQ-LED
-
Image Engineering GmbH & Co. KG
The most flexible, 22 channel, LED based light source is the heart of all adaptive lighting productsCreate your own light by adjusting the 22 channels to your needs. You can simulate standard light sources, reconstruct the daylight distribution from dawn till dusk, create patches of a high saturated color chart, or reconstruct the spectral distribution of a measured light source. By using the individual channels you can even measure the spectral sensitivities of a camera.
-
Product
Chassis - up to Sixteen 8x1 Modules, Thirty Two 4x1 Modules or Any Combination or Configuration of 8x1's, 4x1's, 2x1's and 2x2 Modules
CXAR/128-MF
Chassis
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
Product
Current / Voltage input Panel meter with output options
DM3420
-
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
Product
Multifunctional testers
MI 3125 BT EurotestCOMBO
-
The MI 3125BT EurotestCOMBO performs all the necessary tests for installation safety testing on TT and TN systems. The large graphic display with backlight offers easy reading of results, indications, measurement parameters and messages. Two LED Pass/Fail indicators are placed on both sides of the LCD. MI 3125BT EurotestCOMBO contains integrated characteristics of fuses and RCDs (including B type) for the evaluation of test results.
-
Product
Fully Automated In-line Test System For LED Light Engines
-
We are pleased to announce that we have received an order for the supply of a fully automated in-line test system for testing LED light engines from ASD Lighting, based in Rotherham. The solution provided, consists of an in-line handler fitted with a vision system. The camera software is capable of learning the position of all LED’s on a new pcb, thereby reducing the time to introduce a new product. In addition to identifying the location of any missing or faulty LED’s the tester measures the colour temperature of every pcb. An image is taken of faulty units with the location of any missing LED’s identified
-
Product
2D Barcode Module
UTC-100P-B
-
Sensor: CMOS sensor with 640 x 480 pixel resolution. Illumination & Aiming: White LED illumination; Red LED dot aimer. Typical Frame Rate: 30 frames per second. Motion Tolerance: Up to 100 cm/s (4 in/s) for 13 mil UPC at optimal focus.
-
Product
EZ Tach +Plus Automotive Tachometer
328
-
*Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. *Reads engine revolutions from 0 to 20,000 RPM *Picks up RPM signal wireless or with supplied inductive pickup *Great for setting idle speeds! *Built-in LED Flashlight which can be used while taking measurements *Backlit LCD display *Accuracy +10 RPM
-
Product
13 Pin Towing Socket Tester ( For Halogen Light System)
7630
-
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
Product
Frequency Monitors
FM Series
-
FM Series line-powered frequency monitors are high quality, dependable panel meters designed to continuously monitor line power frequency. Crystal reference-based for high accuracy, these 1/8 DIN/NEMA case style meters come with LED or LCD displays.
-
Product
Full Range Photodiode Array UV-VIS-NIR-SWIRLaboratory Spectroradiometers
-
The SR-Series of full range laboratory spectroradiometers is ideal for a wide range of applications, including Solar radiance and irradiance measurements. Solar simulator test and classification. LED, laser, light source metrology. Radiometric calibration transfer. Remote sensing applications.
-
Product
Handheld Digital Multimeter, 4 digit, with IP 67
U1241C
Digital Multimeter
The strong and solid U1240C Series handheld digital multimeters (DMMs)are the tools technicians or industrial test engineers use to perform their work confidently and efficiently. Designed for handheld users working in various environments, the U1240C series is certified to IP 67 and capable to withstand up to 3-meter (10 feet) drop to suit harsh working environments. The U1240C handheld DMMscan even work longer for you with up to 400 hours of battery life. With the built-in LED flashlight, the U1240Chandheld DMMsallow users to single-handedly illuminate test area.
