Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-124
Precision Resistor Module
The 40-297A-124 (PXI) and the 42-297A-124 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 6.97 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
3U OpenVPX Multifunction I/O Board
68G5P
Multifunction I/O
The 68G5P is a 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. Uniquely designed, the 68G5P provides external access via PCIe x1 and/or SATA II interfaces directly to supported NAI function modules, providing external host SBC function expansion. Additionally, the 68G5P is on NAI’s certifiable product line development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G5P delivers off-the-shelf solutions that accelerate
-
Product
CATV MSA EDFA (1540~1563nm)
HA5700
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5700, the Mid-Stage Access (MSA) CATV fiber amplifier, is developed and produced specially for the dispersion compensation of over-long trunk. HA5700 is composed of lower noise per-amplifier (PA) and booster amplifier (BA). There is access connector between these two amplifiers and thus the dispersion compensation module (DCM) can be accessed in the mid-stage conveniently. It offers the most simple and effective application.
-
Product
Digital I/O via Ethernet
2610
-
Connects to Ethernet via 2601 communication moduleAll channels may be independently programmed as input or outputEight channels have pulse width modulation outputsRJ-11 I/O connectors eliminate need for external terminal blocksSupport for interlocks and multiple power supplies per channelInput channels are debouncedWatchdog Timer
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 12.4 GHz, 50 Ω, N-Type, Failsafe
42-780B-512
Relay
The 40-780B-512 (PXI) and 42-780B-512 (PXIe) are dual failsafe SPDT 12.4 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI Triple SP6T Multiplexer 40GHz 50 SMA-2.9
40-784A-043
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI 4 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-021-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 135x16 2-pole (9 sub-cards)
40-561A-122-135X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
MPOD Crate
-
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which results in 80 up to nearly 500 individually controlled channels per mainframe. Built in a modular way MPOD consists of the mainframe / bin, a front side plug-in controller with Ethernet and USB ports, a fan tray and a power supply which is located in the back.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, MCX
42-876A-102
Multiplexer Module
The 40-876A-102 (PXI) and 42-876A-102 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI Breadboard Module, 1-Slot, 15-Pin D-Type
40-220A-601
Breadboard Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
Multiplexer Module
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-314-HI
Multiplexer Module
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Keysight Triple 1x2 SPDT Unterminated Microwave Switch Module for 34980A
34947A
Microwave Switch Module
The Keysight 34947A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as three independent 1x2 (SPDT) unterminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector, With Interlock
42-153-004-HI
Relay
The 40/42-153-004-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
COM Express Type 6 Basic Module With Intel® Xeon® And 6th Gen Intel® Core™ I7/i5/i3 Processor, Intel® CM236/QM170/HM170
CEM500
-
The CEM500, a COM Express Type 6 basic module, is based on the 14 nm Intel® Xeon® processor E3-1505M v5 and 6th generation Intel® Core™ i7/i5/i3 processor (codename: Skylake-H) with Intel® CM236/QM170/HM170 chipset. The outstanding Intel® Gen 9 HD Graphics enables the CEM500 driving multiple 4K displays without the need of a discrete graphics card. Two DDR4-2133 SO-DIMM supporting up to 32 GB system memory capacity and four SATA-600 with RAID 0, 1, 5, and 10 are available. Additionally, the rugged COM Express computer-on-module Type 6 supports an industrial operating temperature range of -40°C to 85°C for applications in extreme harsh environment. With its full solid, outstanding computing performance and low power consumption design, the CEM500 is targeted at telecommunication, medical imaging, digital signage, gaming machines, military, human machine interface, industrial automation controllers and IIoT applications.
-
Product
Boundary-Scan DIMM Socket Tester
ScanDIMM
-
Maximizing test coverage is an important piece in test procedure development. Unfortunately, not all designs have the necessary requirements in place to accommodate boundary-scan test methods on memory devices. ScanDIMM digital socket test modules are designed to overcome such limitations when testing DIMM sockets utilizing boundary-scan test techniques.ScanDIMM modules provide the capability to instantly turn any DIMM socket into a fully compliant IEEE-1149.1 device. Integration is as simple as assigning the included BSDL file to the reference designator of the target socket and compiling test vectors.In multi-socket systems, multiple ScanDIMM modules can be linked to provide even greater boundary-scan test depth.
-
Product
Matrix Modules for 34980A
Matrix Switch Module
The 34980A matrix modules are full cross-point matrices allowing you to connect any row to any column in the same instance. This is a convenient way to connect multiple test instrument points to multiple points on a device under test. All matrix modules also include a relay switch counter to help predict when relays need to be replaced.
-
Product
RF/Microwave Assembly Capability
-
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-116-HI
Programmable Resistor Module
The 40-230-116-HI (PXI) and 42-230-116-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 8-Slot BRIC Matrix, 132x4 1-Pole (3 sub-cards)
40-562B-121-132X4
Matrix Switch Module
The 40-562B-121-132X4 is a high density BRIC8 matrix module with a size of 132x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Dual Transfer Switch 26.5GHz 50Ω SMA
40-782-532
Dual Transfer Switch
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
NI-9210, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module
784788-01
Temperature Input Module
4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module - The NI‑9210 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9210 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
75 Ohm F-Type to F-Type Cable Assembly
40-977-781-2m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
High Density Modular Switching System
S2084B
-
Universal Switching Corporation
High performance and expandable, the second generation S2084B offers a tremendously flexible architecture for high density 19" rack mounted switching configurations. A total of twenty rear-facing module slots are available to install a growing number module types. Various types of inner backplane configurations are used to deliver a total system configuration by interconnecting the modules internally through the backplane.
-
Product
cRIO-9048, 1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785621-02
Embedded Controller
The cRIO-9047 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
PCIe FPGA Carrier For FMC+, Altera Arria-10 GX1150
PCI536
-
The PCI536 is based on the Altera Arria-10™ GX1150 FPGA in F1517 package. The FPGA interfaces directly to the FMC+ DP 0-23 (single connector) and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. The PCI536 has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. It also has interface to two DDR4, 64-bit wide, with 16 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
