Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
Multifunction I/O Boards
Multifunction I/O
NAI offers a variety of rugged embedded boards - both Multifunction IO Cards & Single Board Computers in OpenVPX, cPCI, VME and PCI/PCIe form factors. When combined with our smart function modules they have the ability to meet a wide range of complex and time-critical sense and response requirements for I/O-intensive, mission-critical applications.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
PXI Triple Microwave SPDT Relay 50GHz 50 SMA-2.4
40-780A-553
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI/PXIe High Density Reed Relay Module, 100xSPST
42-140-221
Reed Relay
The 40-140B-221 (PXI) and 42-140B-221 (PXIe) are 100xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
Product
E-Series Average Power Sensor
E9301A
Power Sensor
Measure the average power of all modulation formats Wide dynamic range (-60 dBm to +20 dBm) and frequency range 10 MHz to 6 GHzHigh maximum power specification Low SWR for reducing mismatch uncertainty Calibration factors linearity and temperative compensation data stored in EEPROM Fast measurement speeds (up to 400 readings per second with the Keysight E4416A)Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Test System
MxDSRC™
-
The MxDSRC Test System simulates systems in the vehicle that interact with the DSRC radio module to create tests closely replicating real-world scenarios. Its integrated approach allows the DSRC components, such as RF quality and protocol conformance, to be exercised with multiple system components. MxDSRC provides a powerful and easy-to-use framework for testing your DSRC system.
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781068-01
Current Input Module
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
Multifunction I/O
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-322
Switch Module
The 40/42-860A-322 is a PXI/PXIe dual insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI 2 Amp MUX, Dual 8-Channel 2-Pole
40-635-106
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI Single Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-531
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options)
-
Product
Engine Controller
FireLynx
-
The fully programmable FireLynx control module is used for Engine Development, Test and Control as well as directing the real time operation of Fuel Injector Test Stands.
-
Product
Cryogenic Temperature Modules
-
Transmit temperature data over long distances to data acquisition locations in research and industrial settings.
-
Product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards) Dual Bus
40-560B-021-92X8-M
Matrix Switch Module
The 40-560B-021-92x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
8 Pin Power D-Type Female Connector, 40A, PCB Mount
40-963-008-RF
D-Sub PCB-Mount Connector
This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-244-HI
Programmable Resistor Module
The 40-230-244-HI (PXI) and 42-230-244-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, External Termination, Failsafe, Remote Mount
42-781A-522-E
Relay
The 40-781A-522-E (PXI) and 42-781A-522-E (PXIe) are dual failsafe SPDT 40 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI 8-Slot BRIC Matrix, 88x8 1-Pole (4 Sub-cards)
40-562B-121-88X8
Matrix Switch Module
The 40-562B-121-88X8 is a high density BRIC8 matrix module with a size of 88x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
SHOCK TESTER
-
King Design Industrial Co., Ltd.
*Shock amplifier is mainly used to small object, and can reach the pulse duration and high acceleration that shock table couldn’t achieve.*Equipped with shock table or different shock module (the theory is to amplify impact energy through second impact), shock amplifier can reach the requirement of high acceleration.
-
Product
Modulator
SFT3401
-
Hangzhou Softel Optic Co., Ltd.
SFT3401 QPSK modulator is a high performance modulator developed according to DVB-S (ETS300-4221) QPSK standard. It has powerful spectral efficiency, advanced anti-jamming and competitive price-performance ratio. Apart from these, this modulator also has access to FM microwave device. Moreover, to guarantee the high transmission performance, this QPSK modulator adopts the disposal of energy diffusing, RS coding, convolution interlacing and pre-modulated baseband shaping. To sum up, all the approaches make this NDS3401 QPSK modulator can be widely used in Broadcasting, Interactive Services, News Gathering and other Broadband satellite applications.
-
Product
Monitoring
7880SA
-
Quintech Electronics and Communications Inc.
The 7880SA module is Evertz' spectrum measurement and analysis module providing high end performance at a low price.
-
Product
Protective Cover, G12x, ITA, Aluminum
410112857
Protective Cover
The G12x Aluminum ITA Protective Cover attaches securely to your ITA for easy and effective protection of contacts and modules. The cover snaps into place and enables smooth maneuverability of the ITA and enclosure over tables and other surfaces.
-
Product
47~2600MHz Satellite TV & Digital TV 1550nm Externally Modulated Optical Transmitter
HES-26D
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HES-26D series 1550nm external modulation optical transmitter can transmit 47~2600MHz analogue signal and digital signal via one single fiber by frequency division multiplexing. It is compatible with any FTTx PON technology, and provides a complete set of high quality low cost fiber trunk transmission and fiber to the building (FTTB), fiber to the house (FTTH) solution for the direct broadcast satellite TV (DBS) and cable analogue TV (CATV) fusion.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
PXI-2598, 26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module
778572-98
Dual Transfer Switch
26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module—The PXI‑2598 is a general-purpose switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2598 is also well suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI 8 Slot BRIC 224x12 2A 1-Pole Matrix
40-597-107
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
VME Generic Carrier Card For Conduction Cooled PMC(PCIbus Mezzanine Card) Modules
AVC-2-CC
-
VME64x (6U) generic carrier card for conduction cooled PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM conduction cooled PMC module for ARINC429, MIL-STD-1553 or any conduction cooled 3rd party PMC module.
-
Product
4-port LAN Module With Intel® XL710-BM1 Ethernet Controller
AX93327
-
The AX93327 LAN module is built with an Intel® XL710-BM1 10 GbE Ethernet controller, incorporating the Intel® DPDK, Jumbo Frames, SR-IOV and VMDq technologies to optimize the processing of network data traffic. This LAN module’s high-density design is specifically adapted for Axiomtek’s 1U and 2U rackmount network appliances, also featuring four 10 GbE SFP+ ports plus a PCIe 3.0 x8 golden finger for high-speed transmission needs, giving customers the freedom to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
