-
Product
FMC 5-Channel Digital I/O Module
FMC DIO
-
Sundance Multiprocessor Technology Ltd.
The fmc-dio-5chttla 5-channel digital I/O module is a simple board for digital I/O on LEMO connectors. It has been designed for testing White Rabbit functionality as part of the SPEC Demonstration Package for White Rabbit, and it can be used for other general purpose applications too.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Transformer Turns Ratio Meter
TTRM 101
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 101 measures only turns ratio where as TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
Cable Manufacturing
-
For years, we’ve been at the forefront of optimizing and automating how cable manufacturers test their fibers. Whether it’s cable design qualification, in-process testing, or final quality control—PK instruments around the globe are running 24/7 measuring thousands of fibers.
-
Product
Multi-Channel Data Acquisition System
PI-3105
-
This highly flexible system is designed to test a wide variety of imaging devices, from low-noise astronomy and medical devices, to military and machine-vision devices with GB/sec data rates.
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Relay Test Set
-
Relay testing equipment is a portable apparatus designed for checking the operating characteristics of protective relays on site. Rr Relay Testing Equipments are designed to facilitate routine test or periodic maintenance test of relays by simulating (as early as possible) fault conditions under which the protective relays are required to function. There are several approaches to the method of testing relays on site. The Relay Testing Equipments are secondary injection type and are intended to be used to test the relays after isolating them from live systems, either physically or electrically.
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
Automatic Softening Point Tester
LD-LSPT-A10
-
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
Product
PCI-6280 , 16 AI (18-Bit, 625 kS/s), 24 DIO PCI Multifunction I/O Device
779108-01
Multifunction I/O
16 AI (18-Bit, 625 kS/s), 24 DIO PCI Multifunction I/O Device - The PCI‑6280 offers analog input, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Handheld Dialysate Meter
Dialysate Meters™ Single & Dual Range
-
The choice of hemodialysis professionals for over 40 years, these compact instruments have been designed specifically to test dialysate solutions. By measuring electrical conductivity, they will quickly determine if dialysate concentrations are correct.
-
Product
Advanced Power System - DC Power Supply, 160 V, 12.5 A, 2000 W
N6977A
DC Power Supply
The N6978A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Software Engineering Services
-
From the many phases of software engineering, designing, building, testing, implementation, interfacing, and support, enGenius has an expert team and network of highly-vetted partners ready to accommodate projects and programs, both large and small. From the vast list of possible requirements, including web applications, architecture, requirements analysis, network security, and recovery and restoration, enGenius has trusted knowledge management resources for state-side and global projects.
-
Product
EPA General Purpose Probes
General Purpose Probe
General Purpose Spring Probe contact solutions are designed for high volume testing and feature the industry-proven Pylon line. General-purpose probes are offered in both replaceable and non-replaceable options.
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
LED Sensor
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
Radar Altimeter Test Set
EA-6061
-
The EA-6061 Radar Altimeter Test Set is designed to test and calibrate any and all radar altimeter systems regardless of protocol or encryption. The EA6061 provides multiple, programmable delays with front panel and/or remote computer control. It features ultra wide bandwidth, low loss, high isolation, and high dynamic range. Able to simulate altitudes up to 6350 feet, the test set operates from 4 to 5 GHz and offers NIST traceable altitude accuracy up to 2 inches
-
Product
TTESync For VxWorks 653
-
TTESync is a synchronization component that allows tight synchronization of VxWorks 653 partitions to the fault-tolerant system-wide cycle time of the TTEthernet communication network. All partitions executed on different modules can be “pinned down” within the overall system cycle time, thus enabling the lowest latency and minimum jitter in message exchange among distributed functions. At system level this results in clean layering, well-understood functional interactions and simpler application design, testing and system integration. System architects can reduce system complexity and further optimize system size, weight, power (SWaP) and life-cycle costs.
-
Product
Exhaust Gas Thermocouples
8TR4C Series
-
The AMETEK 8TR4C Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested, and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading older style Exhaust Gas Thermocouples.
-
Product
Design for Test Service
-
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
Product
Transformer Turns Ratio Meter
TTRM 102
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
Rapid Decompression Test Chambers
CA-RD(H)
-
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
Product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
LED Sensor
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
Product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
-
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
Vacuum Bottle Tester
VBT-75P S2
-
The VBT-75P S2 is Vanguard’s second generation microprocessor-based, portable 75 kV dc vacuum bottle tester. This lightweight, portable tester is designed for testing circuit-breaker vacuum bottles in the field and at the shop.
-
Product
Seno-Con Test System
PANTHER 2K QST
Test System
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
Product
Maxirack 200*60*80cm
OTP2 module no.003
-
The rack serves as the basic structure for your individually designed test system. Various OTP² modules can be installed in the 200 x 60 x 80 cm rack in order to implement a wide variety of test requirements.
-
Product
Digital Surge Tester
25KV, 30KV & 40KV
-
The Digital Surge Tester is designed specifically to test the coils and windings of High range AC Rotating machines ranging up to 13.8KV. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
Product
Quasar Smart Relay Tester
-
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
