Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
MODEM ELIMINATOR
-
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
WAV Trigger
-
The WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Tracks can be controlled via 16 programmable trigger inputs, or by using a native serial control protocol or even MIDI.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
CPCI Dual Industry Pack Carrier
CPCI-6713-2 IP
-
The board consists of private SDRAM and Flash memory attached to the 300 MHz, TMS320C6713B floating point DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is available for downloading programs into a nonvolatile memory. A PCIbus connector provides the interface to the host computer.
-
Product
4-Port Serial Interface
APCI-7500-3
-
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
Communication Converter
F485
-
The F485 is a self-contained device for converting between RS232, RS485 and fiber optic signals. The F485 is electrically isolated to improve communications in noisy environments. The converter uses internal switches to select the signal conversion type and communication rates up to 57600 bps. The F485 converter uses the data on the serial ports to determine direction and therefore requires no hardware handshaking signals from the computer.
-
Product
SDI MASTER
SDI-1
-
The SDI MASTER is a digital, hand-held, battery operated meter that measures six characteristics of High Definition and Standard Definition digital television signals. Use it for fast and accurate set-up and verification of levels, slope-loss and return loss on any SDI (Serial Digital Interface) Digital Television Signal. This meter is a must have for anybody working with digital TV.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
Oscilloscope - 200 MHz, 2 Analog Channels
DSOX3022T
Oscilloscope
200 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
DH Series PT Browser Tip, 16 GHz BW, 3.5 Vpp Range
DH-PT
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
CAMERA LEVEL METER
SDI-2
-
The SDI-2 is a low cost pocket size, digital, hand-held, battery operated meter that measures HD (High Definition) video signals. Use it for fast and accurate set-up and verification of levels and slope-loss on any SDI (Serial Digital Interface) signal. This meter is a must-have for anyone working with HD CCTV cameras or any SDI video signals.
-
Product
CompactPCI Serial, 5 Slots, SSR, 4U, 35HP, 290mm
435V0-E05R-25FA1-000
-
CompactPCI Serial System with 5 Slots: 4x CompactPCI-S.0 Peripheral Slots and 1x CompactPCI-S.0. System Slot on the right side of the system platform. 1x 250W ATX, air-cooled with fan fix-mounted and powder coated.
-
Product
Automotive Protocol Decode/Trigger Software (CAN, CAN FD, CAN XL, LIN FlexRay, SENT) for Infiniium Oscilloscopes
D9010AUTP
-
- Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.
-
Product
Serial to GPIB Controller
Model 4895
-
ICS's Serial to GPIB Controller allows any computer with a serial port to control GPIB devices. Works with RS-232 and 2 or 4-wire RS-422/RS-485 signals. Use to add GPIB Capability to PLCs with serial ports.
-
Product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
787567-01
Controller
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
4-Channel 500 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MACC - embedded
EXC-8000MACC
-
The EXC-8000MACC is a table driven translator (data converter - protocol converter) that enables devices supporting different communications specifications (e.g. Ethernet, Serial, ARINC 429, Mil-1553, Discretes etc.) to talk to each other.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - 3U VPX
Model 52650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Hydrographic Grade Deepwater Singebeam Echosounder
DESO 5DS
-
The DESO 5DS is a hydrographic grade deepwater singlebeam echosounder designed for reliable high performance in deep ocean surveys. It utilizes very high power transceiver electronics to survey the oceans down to 10km depth.The raw data record is stored in proprietary format by Teledyne’s own software and can be acquired, replayed, and analyzed similar to thermal paper records. Depth data is continuously generated on serial and network interfaces and can be recorded by hydrographic software.The DESO 5DS is based on our latest singlebeam sonar technology, designed as a precise and reliable survey tool for the survey from shallow waters to full ocean depth.The DESO 5DS utilizes the most robust automatic control and bottom detection algorithms available — providing you with precise depth information and brilliant water column profile even under the most challenging conditions.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
High Speed Thermal Printer
6041
-
• RS232C serial interface via a 6-pole RJ12 socket• Tested to comply with FCC Standards• Designed for use with Associated Model 6044 and similar devices• Four AA Batteries included• Imported
-
Product
UV Light Meter
Model 308T
-
Built for high intensity applications the NEW OAI Model 308T UV Light Meter is a dependable, direct-reading instrument designed for measuring UV light intensity for UV curing. The Model 308T features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port. Accuracy of the meter is within ±3%and measurement repeatability is within ±3 LSB (least significant bit). Like all OAI precision instruments, the Model 308T provides NIST traceable measurements. This easy-to-use meter is auto-ranging from 0.1 to 1999.9 milliwatts/cm2 full scale when used with the 2000 milliwatts/ cm2 probe. The linearity of the meter in this range is at least ±(.002% + 6 LSB).
-
Product
8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - PCIe
Model 78131
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized versions available
-
Product
TR E5x/msd, 3U OpenVPX™ with an Intel® Xeon® Processor
TR E5x/msd
-
TR E5x/msd is an Intel® Xeon® E3-1500 v5 3U OpenVPX board for enhanced processing performance within the same SWaP envelope. XMC site or front panel for DisplayPort, Ethernet, USB or serial connections. Compliant with VITA 46.11 system management.
-
Product
RS232 Straight-Through Cable, DB-9 Female to DB-9 Male,1m
183045-01
Serial Cable
9-Pin Female DB-9 to 9-Pin Male DB-9 GPIB Serial Cable - The 9F-9M S10 Serial Cable, sometimes referred to as GPIB S10 Cable, connects and controls GPIB devices using the RS232 serial port. The 9F-9M S10 Serial Cable is offered in different lengths.
-
Product
Human Vibration Management Software
HVManager
-
HVManager is a Risk Assessment and Recordkeeping software tool for reporting Vibration measurements and predicting Personal Exposure Levels. It provides reports of vibration measurement data from hand-arm and whole-body measurements acquired from the Larson Davis HVM100 Human Vibration Meter and produces vibration database records by tool type and serial number. HVManager also compiles cumulative predicted vibration exposure levels from any combination of tools and task durations taken from the measurement database.
-
Product
SparkFun Shift Register Breakout
74HC595
-
This is a breakout for the SOIC version of the 74HC595 shift register IC. Clock in data and latch it to free up IO pins on your micro. All pins from the IC are broken out to standard 0.1" spaced headers. The Serial in and out pins are on opposite sides of the board with the remaining pins carried over so that multiple shift register boards can be chained together.
-
Product
PCIe Mini Module
PCIe-Mini-ESCC
Controller
The PCIe-Mini-ESCC module is a Dual Channel serial communication controller with 4K FIFO per Line. The PCIe-MiniESCC module is based on the Z85230 Enhanced Serial Communication Controller, with larger FIFOs and several SDLC improvements from Zilog.
