Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 58610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
-
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
Product
Super Phosphor Oscilloscopes
SDS2000X-E Series
-
The SDS2000X-E series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). It also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. Siglent’s newest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. Also included is the deep memory FFT. This math function uses upto 1 M samples for the FFT calculation, providing the SDS2000X-E with very high frequency resolution. The hardware co-processor executes true fast measurement and math to all of 28M sample points so that there is minimal distortion on analysis. It also supports searching and navigating, on-screen Bode plot, 16 channel digital /MSO (optional), an external USB powered 25 MHz AWG function generator module (option), a USB WIFI adapter for wireless control and monitoring (option), and an embedded application that allows remote control via web browser. The features and high-performance of the SDS2000X-E oscilloscopes cannot be matched else anywhere at this price.
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 6U VPX
Model 57141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
LXI Remote AC Power Management Switch
-
If you have ever read the term "programmable except for the supply on/off switch", Pickering's LXI remote AC power management switch can provide this additional capability in a system with the added benefit of an easy to use LXI interface. This power management switch provides a means of remotely controlling the power status of up to eight instruments in a system through an LXI enabled power management switch. Additionally, the Power Management Switch is available as an RS232 serially controlled version.
-
Product
SparkFun Dev Board
ESP8266 Thing
-
This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off, the ESP8266 is incredibly easy-to-use: firmware can be developed in Arduino, and uploaded over a simple, serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
Power Generator
HD778TCAL
-
Power generator in the range -60mV…+60mV, regulated by PC through RS232C serial port.
-
Product
Serial Controller
PMC522/FP
-
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
Motionnet
-
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).
-
Product
COLORIMETER FOR SMALL DISPLAYS
K-8
-
The Klein K-8 tri-stimulus CIE Colorimeter Probe is designed to be the best colorimeter in sensitivity, stability and speed. It attaches directly to a pc's serial com port (RS-232), and runs with the companion pc program. Whether a desktop or a laptop is used, the Klein measurement application is in control and many additional features are available.
-
Product
TOC Combustion Analyzer
Torch
-
The Torch is considered the premium TOC combustion analyzer due to its many useful features and automated analysis processes. For example, it makes serial dilutions of stock standards to form a calibration curve and auto-dilute samples with concentrations above the calibration curve. The Torch software has built-in diagnostic and troubleshooting capabilities. For a luxury but affordable TOC combustion analyzer that you can just load and walk away, look no further than the Torch. You won't regret it!
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
-
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
Product
SparkFun Serial Basic Breakout
CH340C And USB-C
-
This SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340C and takes advantage of the handy USB-C connector. With USB-C you can get up to three times the power delivery over the previous USB generation at 1.5A and and also solves the universally frustrating dilemma of plugging a USB cable in correctly, because it’s reversible! The Serial Basic works with 5V and 3.3V systems and possesses the capability to auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340C IC to quickly and easily convert serial signals to USB.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
-
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
GPIB To Serial Miniboxes™
-
ICS's GPIB to Serial Minibox™ Interfaces are fully enclosed for benchtop or rack mount applications. The GPIB to Serial Interfaces are available for transparent data transfer and with smart firmware to add an IEEE-488.2 interface to any serial device
-
Product
3U CompactPCI Serial 3-slot SSL w/ RTM w/ Ethernet
1CPCIS-303-L210
-
3U CompactPCI Serial Backplane with 3 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 2x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 3, Ethernet full mesh.
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
PXI-8431/2 , 2-Port, RS485/RS422 PXI Serial Interface Module
778984-01
-
2-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-32
-
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790660-01
-
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
Class I, Division 2 Solution
-
Class I, Division 2 remote I/Os, such as CID1 monitors and CID2 solutions, have met the requirements of hazardous area computer such as explosion proof, oil field drilling, pump station monitoring, chemical plants, pharmaceutical factories, oil pipeline monitoring, tank storage monitoring, and fuel station management. Class 1, Div 2 remote I/O products include data acquisition modules, industrial Ethernet switches, serial device servers, industrial monitors and embedded automation computers, all.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
-
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
PCI Express 2-Port
7203e
-
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
cPCI Serial Backplanes
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
Product
SparkFun Micro OLED Breakout
-
The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro OLED is easy to control over either an SPI or I2C interface.
-
Product
Powered VXS Crates
-
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
-
Product
Efficiency And Innovation, Squeezed Into One Tiny, Affordable Package
LatticeECP3
-
*Up to 16 channels at 3.125 Gbps*800 MBps DDR3, 1Gbps LVDS*Up to 586 programmable sysIO buffers with support for PCI Express, Ethernet (GbE, XAUI, & SGMII), HDMI, SMPTE, Serial Rapid I/O, CPRI and JESD204A/B and more*Up to 150 k LUTs and 6.8 Mbits of SRAM*Wide array of packages as small as 10.0 mm x 10.0 mm with power consumption below 0.5 W
-
Product
PXIe-8822 2.4 GHz Quad-Core Processor PXI Controller
787881-33
-
The PXIe8822 is an Intel Core i3based embedded controller for PXI systems. You can use the PXI-8822 to create a compact or portable PC-based platform for industrial control, data acquisition, and test and measurement applications. This PXI Controller includes a 10/100/1000/2500 BASET Gigabit Ethernet port, two HiSpeed USB ports, two USB 3.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O.
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX4032A
-
350 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
