Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
NFC Physical Layer Test System
IQnfc+
-
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
Product
Physical Layer Test System
N19301B
-
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
Product
BGAN Physical Layer Tester
BPLT
-
Square Peg Communications Inc.
The BGAN Physical Layer Tester (BPLT) supports the testing of physical layer performance and protocol implementation of Radio Access Nodes (RANs) and User Terminals (UTs) implementing Inmarsat’s Broadband Global Area Network (BGAN), Fleet Broadband and Swift Broadband services.
-
Product
Inmarsat-C Physical Layer Tester
CPLT
-
Square Peg Communications Inc.
Square Peg Communications Inc.’s Inmarsat-C Physical Layer Tester (CPLT) is a software application that runs on the generic high-rate Physical Layer Tester (PLTH) platform. The CPLT supports testing of the physical layer performance and protocol implementations of Inmarsat-C Mobile Earth Stations (MESs) and Land Earth Stations (LESs).
-
Product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
-
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
Product
IsatData Pro Physical Layer Tester
DPLT
-
Square Peg Communications Inc.
The IsatData Pro Physical Layer Tester (DPLT) supports testing of the physical layer performance and protocol implementation of Mobile Terminals (MTs) implementing Inmarsat’s IsatData Pro (IDP) services.
-
Product
Physical Layer Switching Systems for Copper LAN, WAN< DSL, Telco Apps with RJ Style Connectors
RJ Series Switching Systems
-
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration.
-
Product
Industrial Ethernet Physical Layer Devices
-
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
Product
SDH Ethernet Testers
-
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
-
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
IPTV Testing
-
EXFO offers IPTV test solutions to assess the network copper physical layer, validate the xDSL service and test the performance of the IPTV component at any stage of the deployment. Our Ethernet IPTV testing, IPTV analysis capabilities and advanced IPTV monitoring solutions offer complete end-to-end quality of experience (QoE) assessment for IP video. EXFO enables providers to successfully introduce video services faster and manage them more cost-effectively, by continually ensuring the highest service quality.
-
Product
Ethernet PHY
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
Product
64 Gbaud High-performance BERT
M8040A
-
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Digital Services
-
*Processor verification experience*Memory verification*Bus protocols and DMA verification*Expert in high speed controller verification*Physical layer (PHY) verification
-
Product
AXIe M8000 Series of BER Testers
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
ARINC PCI Interface Card
PCI-A429
-
Alta Data Technologies’ PCI-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
Product
Physical & Protocol Layer Testing Solutions
-
Testing ensures expected functionality, increases stability, improves reliability, and provides a higher quality product to you customers
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
-
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 8-Channel, 2-Pole
42-739-003
-
The 40-739-003 (PXI) and 42-739-003 (PXIe) are single 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
Bit Error Ratio Testers
M8000 Series
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
Network Connectivity Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
QualiPhyer Tools
-
QualiPhyer is a family of software packages used to test a product’s conformance to IEEE 802.3™ and MIPI Alliance electrical and optical standards for Ethernet and MIPI devices. These packages can be used to control oscilloscopes and traffic generators over Ethernet or GPIB connections to test the physical layer characteristics of devices. The software processes waveforms from the scopes to produce results based on algorithms developed at the UNH-IOL.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Development Switch
AFDXSwitch Lab
-
The AFDXSwitch Lab operates in accordance to all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally the switch comes with advanced features like 1 Gbit/s speeds, flexible physical layer configuration and extended environmental ratings. The AFDXSwitch Lab provides the full range of all technical functionalities of TTTech’s certifiable AFDX production switches, making it the optimal switching solution for a large variety of different application areas.
-
Product
100-FX Fiber Optic Ethernet PMC
3006
-
The Ethernet 100-FX Adapter provides a single port Ethernet connection using Fiber Optic media. An AMD 79C973 Ethernet controller provides a integrated link and physical layer for operating at 100 Mb/s. The Fiber Optic connector used on the board can be either the ?SC Duplex? style, or the ?ST RX/TX? style and is identified by the Technobox Part Number.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
42-739-004
-
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
PXI DeviceNet Interface Module
-
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
Product
PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-A429 and ECD54-A429
-
Alta Data Technologies’ PCCD-A429 & ECD54-A429 interface modules offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
