Serial Digital Interfaces
A family of digital video interfaces standardized by SMPTE.
-
Product
PXI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module
778969-01
Digital I/O Module
64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 2m
156166-02
High Speed Digital Cable
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 2m
-
Product
Digital IO
PA64IX
Digital I/O Module
The PA64IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 1024 bi-directional pins (16 boards). The PA64IX also supports dee pattern memory by offering 32 M of on-board vector memory with static per pin direction control and with test rates up to 33 MHz.
-
Product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
Digital I/O
IP-DIGITAL482
Digital I/O Module
IP-DIGITAL482 is a single-wide IndustryPack configured to maximize the number of digital I/O lines. The 48 lines are accessible as individual bits or as bytes. These lines may also be used for 8-bit and 16-bit I/O with handshake lines. IP-DIGITAL482 is a drop-in replacement for the IP-DIGITAL-48.
-
Product
FEC Accelerator Based On Intel® VRAN Dedicated Accelerator ACC100
PCIe-ACC100
Interface Card
ADLINK’s PCIe-ACC100 is a PCIe interface accelerator adapter developed based on Intel's vRAN Dedicated Accelerator ACC100 eASIC chip. It supports 4G and 5G codec acceleration, checksum rate matching, onboard 4G ECC memory, and hybrid automatic repeat request technology (HARQ). The PCIe form factor HHHL (half-height, half-length) can meet the needs of most application scenarios.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785959-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
42-414-101
Digital Input Module
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenientway of determining the status of input lines by comparing the input voltage with two threshold voltages - quicklyestablishing if the input is low, high or in an intermediate logic state.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s on 24 Channels
DN6.221-24
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PXI Digital I/O Module
Digital I/O Module
PXI Digital I/O Modules offer up to 96 channels of digital I/O, with compatibility for a variety of voltage and isolation levels. Some models include programmable input filters to eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter. PXI Digital I/O Modules are ideal for a range of applications, from manufacturing test and industrial control to advanced aerospace and laboratory research.
-
Product
PXI Remote Control Interface Cable, 7m
41-924-700
Remote Interface Cable
The 41-924-700 is a 7m cable accessory for the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
Digital Multimeter
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
Product
C Series Digital Module
Digital Input Module
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
USB-6501, 24-Channel, 8.5 mA, Digital I/O Device
779205-01
Digital I/O Module
The USB-6501 is a portable, bus-powered USB digital I/O device, providing reliable data acquisition and control at a low price. The device provides overvoltage protection its digital I/O lines and a 32-bit counter. With plug-and-play USB connectivity, the USB-6501 is simple enough for home and academic applications, but robust and versatile enough for laboratory and industrial applications.
-
Product
Interface
RXMC2-1553
Interface
Abaco Systems ’ RXMC2-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. The 4 channel RXMC2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5050
Digital I/O Module
The GX5050 is a high speed Dynamic Digital I/O card that provides a full set of features that is comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GC5050, but the GX5050 is a PXI card (6U) and the GC5050 is a PCI card. Both have the ability to operate independently of the host computer when in RUN mode.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5941-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PXIe Remote Control Interface Module
43-921-003
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
Product
Digital and Serial I/O
Digital I/O Module
At Abaco, we're committed to the future of your VME systems, and we provide you with the flexibility and functional density you need.
-
Product
Handheld Digital Multimeter Transit Case, Aluminum-clad
U1172A
Digital Multimeter
Use this aluminum-clad case to transport your handheld digital multimeters (DMMs).
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
16 / 180 MS/s Bit Waveform Digitizer
WFD16
Waveform Digitizer
The WFD16 is a 16 bit Waveform Digitizer for high-speed / high resolution waveform capturing and analyzing. The fully differential signal path ensures an exceptional high signal quality. Despite this emphasis on signal quality the WFD16 also has a good DC accuracy. The module features differential inputs with a 50 Ohm or 10 kOhm termination and a with a programmable common-mode voltage.
-
Product
Digital to Synchro Converter
DSPH
Digital / Synchro Converter
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
Product
High-Speed A/D 12-Bit Digitizers
Digitizer
GaGe 12-bit resolution digitizer models divide the input voltage range into 4,096 different digitization levels, which improves the delectability limit by a factor of 16 over the 256 levels of an 8-bit resolution digitizer model.
-
Product
PXI/PXIe High-Accuracy Multi-Measurement Device
PXM(e)7822
Digital Multimeter
The PXM Multi-Measurement Devices combine the functionalities of a 16 Bit digitizer, a 24 Bit multimeter, a timer/counter and a highly flexible trigger matrix in a PXI or PXIe device.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785593-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
GPIB Smart Serial Interface
Model 4866
-
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
Interface Card
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
-
Product
NI-9436 , 120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module
784338-01
Digital Module
120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module - The NI‑9436 works with industrial, high-voltage logic levels and signals to connect directly to a wide array of industrial devices such as fans and motors. Each channel accepts signals from 120 VDC to 240 VDC and 120 VAC to 240 VAC; features transient overvoltage protection between the input channels and earth ground; channel to channel and channel to earth isolation up to 250 Vrms; and has an LED that indicates the status of each channel.
