-
Product
FieldFox Handheld RF and Microwave Analyzers
-
Measure with confidence from 4 to 50 GHz - precise measurements agree with benchtop resultsCapture every signal with real-time spectrum analysis (RTSA) up to 50 GHzWithstands your toughest working environments - rugged enough to meet MIL-specsWeighs less than alternative solutions- millimeter-wave models 30% lighter than other handheldsChoose to configure as a cable and antenna analyzers (CAT), vector network analyzers (VNA), spectrum analyzers and all-in-one combination analyzer
-
Product
Calibration Kit
N612
-
*N612 Calibration Kit, * Frequency Range: up to 6 GHz, * Impedance: 50 Ohm, * Connector Type: N-type.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
42-785C-522-T
Multiplexer Module
The 40-785C-522-T (PXI) and 42-785C-522-T (PXIe) are dual failsafe SP6T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2230-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
NF50 N-Female to N-Female Adapter
-
NF50 Adapter, N-Female to N-Female, Frequency Range: up to 6 GHz, Impedance: 50 Ohm
-
Product
Frequency Converter Upwards
UPCONVERTER 10 GHz VXI
-
The UPCONVERTER 10 GHz control software is VXI Plug & Play and does not depend on the module version. The software allows for automated calibration and verification of the main characteristics of the device.
-
Product
Coax/20-26 GHz/ 75 Ohm HD, Module, Receiver, iCon Series, 18 Position
510160114
Receiver Module
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161114. (May mate with other ITA modules, as well.)
-
Product
Architecture P4040/4080 Processor
VME-186
-
Curtiss-Wright Defense Solutions
The VME-186 VME Single Board Computer is based on NXP's high-performance QorIQ P4080 SOC multi-core processor. With four or eight Power Architecture cores running up to 1.5 GHz, and up to 8 GB of high bandwidth DDR3 SDRAM, the VME-186 SBC provides processing and a variety I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
Product
19" Fanless Panel PC With Intel® Atom™ X6425E Processor
PPC-419 EHL
Panel PC
19" SXGA TFT LCD with resistive (default)or projected capacitive(by request) touchscreenIntel® Atom™ x6425E quad-core, 2.0 GHz processorFanless, slim designSupports 1 x 2.5" SATA and 1 x M.2 B key slot for expansion1 x PCI/PCIe x1 expansion slotWide operating temperature range (-20 ~ 60 °C/-4 ~ 140 °F)Wide range DC support (9 ~ 32 VDC)1 x isolated RS-422/485 with automatic flow controlDual 2.5GBASE-T Ethernet supports Time-Sensitive Network(TSN) technology
-
Product
Mixed Signal Oscilloscope - 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX4104A
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
RF Power Splitter, Combiner, Divider P67, 2 Way, SMA Female, 2.4 - 6.0 GHz
PD2558
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (25 dB avg)Excellent VSWR (1.15 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-015-004
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
50/75 Ohm Micro Coax Contacts
-
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
Product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Infiniium EXR-Series Oscilloscope: 2.5 GHz, 8 Channels
EXR258A
Oscilloscope
2.5 GHz on all 8 channels, 8 instruments integrated in one, hardware accelerated plotting, and fully upgradeable
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
-
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
Calibration Kit
N911
-
*N911 Calibration Kit, * Frequency Range: up to 9 GHz, * Impedance: 50 Ohm, * Connector Type: N-type.
-
Product
Microwave Relays
CXM/2x2
-
CXM/2x2-F-SMA Microwave Relays have a Normally Closed (NC = OFF) and Normally Open (NO = ON) Position as shown in the drawing on the left. They can also be used as a terminated 2x1 relay. Usefull for swapping signals between devices, reversing signal flow or interfacing to larger configurations. Specifications Bandpass DC to 18 GHz Insertion Loss 0.3 dB @1 GHz, 0.8 dB @ 18 GHz VSWR 1.2:1 @ 1 GHz, 1.5:1 @ 18 GHz Isolation -80 dB @ 1 GHz, -60 dB @ 18 GHz
-
Product
Coaxial Matrix Switching Systems
CX Series
-
This series is broken up into the following groups:*CXB Series Modular Matrix systems for coax signals up to 100 MHz.*CXG Series Relay Matrix systems for DC to 800 MHz 50 or 75 ohm signals.*CXS Series Solid State non-blocking full fan out systems 1 to 2.5 GHz.*CXF Series Relay Matrix non-blocking, full fan-out systems 10 to 700 MHz.
-
Product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58641
-
- Ideal radar and software radio interface solution- Two 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Four 2-Channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one-channel DDC (digital downconverter)- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
RF Power Splitter, Combiner, Divider IP67, 3 Way, SMA Female, 2.4 - 6.0 GHz
PD2568
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (20 dB avg)Excellent VSWR (1.25 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Failsafe
42-785C-573-E
Multiplexer Module
The 40-785C-573-E (PXI) and 42-785C-573-E (PXIe) are triple failsafe SP6T 67 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-415-014
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Spot-Focusing Lens Antennas
-
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
Product
Noise Source Test Set, 10 MHz to 26.5 GHz
N2002A
-
The N2002A noise source test set is a low cost, stand-alone instrument that, as part of a calibration system, enables fast, repeatable calibrations with minimal levels of uncertainty.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-016
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
8 GHz Agile Synthesizer
PicoSource™ AS108
-
The PicoSource™ AS108 Agile Synthesizer generates signals to meet the needs of both benchtop and integrated module applications. Its broad 300 kHz to 8 GHz frequency range, fast settling and programmable phase, frequency and amplitude match it to a wide range of applications, with the added advantages of low cost, small footprint and 12 to 15 V power requirement.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 11 dB, 1 dB steps
8494A
Attenuator
The Keysight 8494A, dc to 4 GHz manual step attenuator, offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
