Si
atomic number 14 tetravalent metalloid chemical element.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
NRZ Analysis for Signal Integrity Studio, WavePulser 40iX High-Speed Interconnect Analyzer
WAVEPULSER-SI-STUDIO-NRZ
-
Signal Integrity (SI) Studio uses SDA Expert (SDAX) serial data analysis software options to simplify NRZ or PAM serial data jitter, eye diagram, noise and crosstalk measurement and analysis setup.
-
Product
MPI PCB Probe Systems
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
Product
Magnetic Susceptibility Meter
SM-20
-
The SM-20 magnetic susceptibility meter is very useful tool for a number of geological and geophysical applications where the unique sensitivity of 10-6 SI units together with its small, shirt-pocket size and low weight are appreciated.
-
Product
Potentiostats
-
AMETEK SI offers a range of bipotentiostats, single and multi channel potentiostats and galvanostats through both the Princeton Applied Research and Solartron Analytical brands.
-
Product
Force Calibration
-
Trescal provides full Force Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Force Calibration services can be delivered at your site or at our lab. Accreditations for our force calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
DVB Analyzer
DVB Inspector
-
DVB Inspector is an open-source DVB analyzer, written in java. It can show the logical structure of the DVB SI and PSI data. It also shows bit rate usage data. DVB Inspector can be used to analyse contents; MPEG Video structure, teletext, DVB subtitles, DSM-CC Object carousels.
-
Product
Mass Calibration
-
Trescal provides full Mass Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Mass Calibration services can be delivered at your site or at our lab. Accreditations for our mass calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Silicon Irradiance Sensors
-
Measure the irradiance intensity on your photovoltaics system precisely at an affordable price with IMT Technology’s robust silicon solar irradiance sensors (Si sensors).
-
Product
Semiconductor Metrology Systems
-
MTI Instruments'' semiconductor wafer metrology tools consist of a complete line of wafer measurement systems for virtually any material including Silicon wafer (Si), Gallium Arsenide wafer (GaAs), Germanium wafer (Ge) and Indium Phosphide wafer (InP). From manual to semi-automated wafer inspection systems, the Proforma line of wafer metrology inspection tools is ideal for wafer thickness, wafer bow, wafer warp, resistivity, site and global flatness measurement. Our proprietary push/pull capacitance probes provide outstanding accuracy throughout their large measurement range, allowing measurement of highly warped wafers and stacked wafers. MTII''s solar metrology tools include off line manual systems for wafer thickness and Total Thickness Variation (TTV), as well as, in-process measurement systems capable of measuring wafer thickness, TTV and wafer bow at the speed of 5 wafers/second.
-
Product
AC Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
Product
Process EDXRF Spectrometer
NEX LS
-
Applied Rigaku Technologies, Inc
Featuring advanced third generation EDXRF technology, the Rigaku NEX LS represents the next evolution of scanning multi-element process coatings analyzers for web or coil applications. To deliver superior analytical performance and reliability, the EDXRF measuring head assembly was derived from the established Rigaku NEX Series high-resolution benchtop instrumentation. With this proven technology, the Rigaku NEX LS delivers rapid, non-destructive, multi-element analyses — for coat weight, coating thickness and/or composition — for elements from aluminum (Al) through uranium (U). The measuring head is mounted on a rigid beam and is equipped with a linear traversing mechanism positioned over a roller so that the head-to-surface distance is constant. Common applications include silicone release coaters, converters, denesting Si for vacuum-formed plastics, RoHS compliance, conversion coatings, metalized plastic, top coatings on metal coil and fire retardants on fabric.
-
Product
4-port Serial Interface, Modular, With/without Optical Isolation, 3.3V/5V, With 9-pin Connectors
APCI-7500-3/4C
-
*This model has 4x 9-pin D-Sub male connectors on 2 brackets*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)
-
Product
UV TOCONs
-
SiC based UV sensor with integrated amplifier and 0 – 5 V voltage output. Measures intensities from 1.8pW/cm² up to 18W/cm². Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Also available for blue light (GaP chip) or visible light (Si chip) measurement. Available in TO5 housings or as miniature sensor probes (stainless steel or plastic). Special TOCONs for hydrogen flame sensing (TOCON_F) and for fire detection (TOCON_N) available. Also available for operating temperatures up to 120°C (standard is 85°C). Please learn more about the sglux TOCONs here: TOCON selection guide and here: TOCON User Guide.
-
Product
4-Port Serial Interface
APCI-7500-3
-
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
Product
KV CAPS
1000 V
-
Macom Technology Solutions Holdings Inc.
The MACOM KV CAPS™ Si high voltage capacitors feature very high working voltage ratings, very low loss and excellent stability by virtue of their novel internal construction and very high-quality dielectric layers. These capacitors are available in surface mount (SMT) plastic packages or in hermetic ceramic packages.
-
Product
Seismometers
-
SI value, the so called “velocity response spectrum”, is one of the standards to express an earthquake''s destructive power against structures. SW-74SI is an advanced model equipped with alarm output to 10-step and SI value output.
-
Product
Acoustic Calibration
-
Trescal provides full Acoustic Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Acoustic Calibration services can be delivered at your site or at our lab. Accreditations for our acoustic calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Avalanche Photodiodes
-
Excelitas offers Avalanche Photodiodes (APDs) on both Silicon (Si) and InGaAs materials. Si APDs cover the spectral range of 400 nm to 1100 nm and the InGaAs APDs cover 950 nm to 1550 nm. An Avalanche Photodiode (APD) provides higher sensitivity than a standard photodiode and is for extreme low-level light (LLL) detection and photon counting.
-
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
Magnetic Calibration
-
Trescal provides full Magnetic Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Magnetic Calibration services can be delivered at your site or at our lab. Accreditations for our magnetic calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
-
-
Product
Hardness Calibration
-
Trescal provides full Hardness Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Hardness Calibration services can be delivered at your site or at our lab. Accreditations for our hardness calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Torque Calibration
-
Trescal provides full Torque Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Torque Calibration services can be delivered at your site or at our lab. Accreditations for our torque calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
EMC Calibration
-
Trescal provides full EMC Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. EMC Calibration services can be delivered at your site or at our lab. Accreditations for our emc calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Photodiodes
Avalanche
-
Similar to photomultipliers, avalanche photodiodes are used to detect extremely weak light intensities. Si APDs are used in the wavelength range from 250 to 1100 nm, and InGaAs is used as semiconductor material in APDs for the wavelength range from 1100 to 1700 nm.
-
Product
Chemical Calibration
-
Trescal provides full Chemical Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Chemical Calibration services can be delivered at your site or at our lab. Accreditations for our chemical calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
Product
Power Meters andCalibration Cells
-
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
Product
KV CAPS
500 V
-
Macom Technology Solutions Holdings Inc.
The MACOM KV CAPSTM Si high voltage capacitors feature very high working voltage ratings, very low loss and excellent stability by virtue of their novel internal construction and very high-quality dielectric layers. These capacitors are available as unpackaged chips. The chips have gold bonding surfaces on both terminals to enable excellent bonding and minimum contact resistance.
