Diagnostics
Test routines run to determine errors.
-
-
Product
Access Network Diagnostics
-
As fiber networks are built and services scale, Fiber Diagnostics helps Service Providers manage their customers’ experiences by ensuring successful installation and service start up, while decreasing time to revenue. Once the fiber network is in service, Enghouse Fiber Diagnostics assures customer satisfaction through improved customer service and rapid time to repair, while reducing operational costs.
-
Product
Cable Testing and Diagnostics
-
Testing devices are required for successful commissioning of underground cable networks or repairs. Diagnostic testing devices are used for evaluating the cable status, which enables optimised and anticipatory maintenance planning and thus minimises failures. This planning is best established with the BAUR diagnostics system.
-
Product
Elevators Diagnostics System
Vector
-
Lift diagnostics system “Vector” is used for measurements in the course of elevators diagnostics and enables measurements of the following parameters:
-
Product
Broadband Diagnostics
TruVizion
-
TruVizion gives you a comprehensive view into the health of your cable or DSL network, including up to 90 days of historical data.PreEqualization Analyzer lets you quickly find upstream impairments like reverse splitters, loose or corroded connectors and bad wiring. Plus, you can be proactive and actually fix those problems before they affect service for your subscribers.RF Inspector is an inexpensive app that can do what a meter can do, except it can do it on a tablet from wherever you happen to have Internet access. That means in the office, at home, or in the field.Upstream Analyzer shows you the RF signals for all ports and modems on your Cisco CMTS without any additional equipment, cabling or connectors, and yes, you can see ingress under the carrier with one click.
-
Product
Point of Care Diagnostics
-
ams is revolutionizing the lateral flow tests by introducing a highly performant spectral sensor that enables superior test quality.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
Heavy Duty/Commercial Automobile Diagnostics
-
Diagnostic leak detection equipment specifically designed for heavy-duty vehicles in industrial, agricultural, and commercial applications.
-
Product
OBD Protocol Diagnostics
-
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
Product
VLF Testing and Diagnostics Unit
Frida TD
-
Cable testing and diagnostics with the BAUR frida TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations: frida: Used for cable and cable sheath testing of medium-voltage cables and electrical equipment up to 20 kV. Another function is insulation testing on electrical equipment.frida TD: Expands the functional scope of frida with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissipation factor diagnostics in one device* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
Product
Machinery Diagnostics
Smart Machine Checker (SMC)
-
The Smart Machine Checker is designed to be used by machinery mechanics to give a clear and accurate automatic diagnosis of rotating equipment. Requires no vibration expertise or internet connection. The SMC replaces the HAWK.
-
Product
In Situ Diagnostics
-
For researchers working on ultra thin films and novel interfaces, Neocera offers insitu, real-time process control and diagnostic tools such as high-pressure RHEED, Low Angle X-ray Spectroscopy (LAXS) and Ion Energy Spectroscopy (IES). RHEED provides exceptional growth control via RHEED intensity oscillations and the Structural data via diffraction. LAXS is a complimentary to RHEED and provides real-time Compositional information. IES provides energetics of the laser generated plasma plume which is directly responsible for obtaining high quality films and interfaces.
-
Product
VLF Testing and Diagnostics Unit
Frida
-
Cable testing and diagnostics with the BAUR frida. The portable and powerful high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 20 kV and electrical equipment. Another function is insulation testing on electrical equipment.* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
Product
Instrument Maintenance & Diagnostics Software
-
Instrument Maintenance and Diagnostic Software monitors instrument health and provides email-based alerts, notifying you when to consider replacing key consumables, when to perform preventive maintenance, and when an instrument stops running anywhere in your lab. This software is also designed to track inventories, manage schedules, aggregate data, provide resource visibility, and integrate with other lab systems.Monitoring is available for a wide range of instruments and allows you to capture lab-wide instrument utilization data across all of your workflows. These capabilities are designed to deliver reduced downtime and sustained instrument performance, driving simplification, optimization, and transformation of lab operations.
-
Product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
-
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
Product
VLF Diagnostics System
PHG 80 TD
-
Cable testing and diagnostics with the BAUR PHG 80 TD. The combination of the PHG 80 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
Product
Vibration Control, Monitoring and Diagnostics System for Hydraulic Units
-
Stationary system for vibration control, monitoring and diagnostics of hydraulic units is used for constant technological and safety control, diagnostics of vibrational and mechanical parameters of hydraulic units and auxiliary equipment of hydroelectric power stations in accordance with the applicable requirements.
-
Product
Auguscope Portable Diagnostics
-
The Auguscope incorporates over 3 years of Electronics and Analog circuit development, resulting in best in class analog signal sampling at never before seen sampling rates. The Auguscope can record both Vibration and Ultrasonic (AE) sensors and can be used for mechanical diagnostics, as well as leak detection, pump cavitation and steam traps. The result is a small, portable device, that replaces over $40,000 worth of monitoring equipment.
-
Product
High Sensitive Radiometers for Plasma Diagnostics
-
ELVA-1 radiometers for plasma diagnostic are worldwide known product. The custom designed ECE radiometers have been installed at lots of Tokamaks
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
-
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
Systems for Vibration Monitoring and Diagnostics
-
*Reliable permanent vibration monitoring according to DIN ISO 10816*Cost effective real-time vibration monitoring for machine protection*Increase availability and reliability, reduce maintenance costs and ensure quality*Compact field units and modular control cabinet systems*Analog output and switching output for alarm function
-
Product
Boundary-Scan Advanced Diagnostics Option for ScanExpress Runner
ScanExpress ADO
-
Being able to quickly pin point faults can provide the difference between a long night at the office or spending time at home with the family.ScanExpress ADO is designed to take diagnostic guesswork out of the equation. The fully automated analysis option quickly parses test vectors and identifies faults down to the net and pin level.
-
Product
Advanced Diagnostics
-
Providing wireless vehicle communications between the vehicle and tablet and supporting the latest DoIP, D-PDU and Mega CAN vehicle communication protocols.
-
Product
VLF Testing and Diagnostics System
PHG 70 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 70 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate * individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltageCompact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
Electric Vehicle Diagnostics
-
Innovative diagnostic leak detection technology designed exclusively for battery-electric vehicles.
-
Product
High-Voltage Test and Diagnostics Device
Viola
-
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-
Product
Vibration Diagnostics System
VDS
-
The Vibration Diagnostic System (VDS) is a vibration data management system designed specifically for the machinery Predictive Maintenance (PdM) community. It harnesses the graphic display capabilities of Crystal Instruments EDM Software for the work of machinery vibration analysts.
-
Product
5 kV Electric Motor Analyzer
MCE
-
The MCE is the most comprehensive static electric motor test equipment available on the market today. Through a series of powerful diagnostic tests, the MCE provides a complete look at the health of an offline motor. The MCE provides critical information to technicians allowing them to diagnose problems early, thus reducing unwanted downtime.
-
Product
Software
Delta-X
-
Delta-X provides software diagnostic solutions to assess and track the condition of electrical apparatus used by utilities and heavy industry. Delta-X’s Transformer Oil Analyst™ (TOA) is the market leading tool used by high-voltage equipment experts to manage and interpret insulating fluid test data, including dissolved gas analysis. Generation, transmission and distribution utilities, as well as leading industrial operations around the world, rely on Delta-X to provide accurate and timely insights into the condition of their high-value assets.
-
Product
Transformer Test Equipment
-
DV Power test instruments perform various diagnostic tests on power and instrument transformers. Even more, a unique feature is a condition assessment of on-load tap changers. Performing a transformer test before their breakage can be crucial.Test instruments are portable and enclosed in durable metal cases. Also, the 19” rack-mounted version suitable for factories is available as well.Applications supported by DV Power transformer test equipment include:Winding resistance measurement (IEC 60076-1)Analysis of on-load tap changers (IEC 60214-1)Heat run test (IEC 60076-2)Automatic transformer demagnetizationTurns ratio measurement of power and instrument transformers (IEC 60076-1)Excitation current measurementPhase angle measurementTransformer vector group detectionDemagnetization status verificationAll of the above-mentioned measurements are performed with the highest accuracy.The advanced DV-Win PC software collects both numerical and graphical results. As a result of that, these features provide an easier and more efficient analysis. After the test, DV-Win software generates a test report with a single click. Furthermore, a user can easily customize the test report and save it in different formats, such as XLS or PDF.Finally, the analysis of on-load tap changers is performed by the new method called dynamic resistance measurement (DRM). This is a non-intrusive method. Therefore, it allows detecting problems in on-load tap changers without disassembling them.
