-
Product
3 1/2 Digital Process Meter
CSN Series
-
CSN Series 3 1/2 Digital Process Meter is a simple type of economic Panel Meter, and its large LED display with 20.0mm and anti-jamming design, quality, reliable, easy to install.Full range can be specified DC voltage / current, thermal resistance , load cell, potentiometer , Resistance and pulse signals such as the general measurement requirements.
-
Product
Ionization bars
-
Wolfgang Warmbier GmbH & Co. KG
Suitable for down-stream applications ie "laminar airflow boxes"Air assistance for various applicationsComplies with IEC 61340-5-1 Ed. 1.0 (2007-08)Pulsed AC high voltage IonizationEach tip emits positive and negative ionsSelf-balancing ± 30VControl input and alarm output connectorPower supply 230V / AC via controllerOne controller is suitable for two ion barsAdjustments on controller sideEasy emitter replacement
-
Product
RH850 Family (Automotive only)
RH850/E1x
-
RH850/E1x microcontrollers are ideal for powertrain applications, with built-in hardware for knock control such as delta-sigma A/D converter, Digital Filter Engine (DFE), Advanced Timer Unit (ATU-IV), and Autonomous Pulse Adaptor (APA), and engine control such as fuel injection control.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
IP Pulse
-
IP Compatible card with 4 programmable pulse generators. TTL or RS422 / RS485 compatible outputs. Programmable pulse - nS to seconds. Programmable count or free
-
Product
SHOCK TESTER
-
King Design Industrial Co., Ltd.
*Shock amplifier is mainly used to small object, and can reach the pulse duration and high acceleration that shock table couldn’t achieve.*Equipped with shock table or different shock module (the theory is to amplify impact energy through second impact), shock amplifier can reach the requirement of high acceleration.
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
Product
2-CH Counter/Frequency Input Module
ND-6080
Data Acquisition Module
- Channels: 2 independent 32-bit counter- Input Frequency: 100 kHz max.- Isolation Voltage: 5000 VRMS- Input Pulse Width: > 10 µs*- Max. Count: 4294967295 (32-bit)
-
Product
Hand-held Tachometers
-
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
Product
Basic Pulsed-RF Measurements
S95025B
-
Eliminate the need for external test sets and pulse generators using the built-in pulse modulators in the PXI VNA pulsed-RF measurement solution. S95025B also controls external pulse generators and modulators and can synchronize to external master pulses. If using external master pulses or external pulse modulators, the Y1731A PXI adapter odule is recommended.
-
Product
Premium Data Loggers with 1-4 Channels
-
Premium Data Loggers for temperature, humidity, co2, atm. Pressure, voltage, current, pulse and 2-state inputs.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
Pulse energy and power measuring instrument
LEM 2410
-
A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity allow a wide range of sensor heads to be used. The large graphic display offers space for a variety of display and analysis choices. The digital display can be used for determining the energy, frequency and average power.
-
Product
Continuous Time Interval Analyzers
GT668PXIe-40
-
GuideTech’s GT668PXIe-40 PXI 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system at low cost. High accuracy 50MHz time base with NIST traceable calibration. Some of the GT668PXIe-40 measurements include Jitter measurements, PLL & Clock Jitter, Spread Spectrum Modulation, PLL Lock Time, Frequency, Period, Pulse Width, Skew, Tpd, Rise/Fall Time, Time Interval Error and more.
-
Product
Fibolocator
-
Fibolocator is an innovative device for measuring and characterizing breaks and other backscattering-causing faults in optical fibers. Time-resolved correlation reflectometry is the principle on which the device is based. It analyzes the backscattered light like a pulse OTDR, but unlike such OTDRs, cw laser diodes are used. The requirements for the test signal and the complexity of the system are low, which leads to very low costs for OEM subsystems.
-
Product
Primary Cable Fault Locating
Directional Impulse Detector
-
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
Product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
-
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
Product
Power Meters and Sensors
-
Anritsu offers the world's most comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g. radar), while the ML2480B series is suited for Wide-band power measurements on signals such as W-CDMA, WLAN, and WiMAX.The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package.
-
Product
250 MS/s, Two Channel, Arbitrary Waveform Function Generator PXI Card
GX1120
Waveform Generator
The GX1120 is a high performance, two-channel PXI arbitrary waveform generator that offers function generator and arbitrary waveform generator functionality within one instrument. Built-in waveforms are available for use with both the DDS or AWG modes of operation and include Sine, Triangle, Ramp, Noise, and pulse waveform generation.
-
Product
RADAR Stability Testing
PN9002
-
Radar component and system testing usually evokes images of complex, expensive measurement systems occupying multiple equipment racks. In some cases, radar equipment designers have even used entire radar systems as a proving ground for their new components and modules. With the introduction of the PN9002 pulse-to-pulse radar stability test set from Noise eXtended Technologies , radar testing has become significantly less complex and costly. The modular PN9002 system provides outstanding dynamic range at frequencies from 2 to 18 GHz and optionally from 0.4 to 18 GHz.
-
Product
PD (Partial Discharge) Tester
-
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
Product
Flex Power In-Line Auto Shut-Off Pulse Tools
-
Auto shut-off in-line pulse tool that automatically shuts off the air supply when the pre-set torque is reached. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Offers comfortable rubberized non-slip grips for easy handling and excellent thermal ergonomics. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
Fiber Optic Modem
VCH-608
-
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
Product
Coupled Cavity TWTs
-
Communications & Power Industries
• Frequencies from 2.7 to 37.5 GHz• Peak levels: 500 W to 180 kW• Cooling type: air, liquid, conduction• Depressed or grounded collectors• CW (Continuous Wave) and Pulsed
-
Product
FiberPulse OTDR
XO1
-
FiberPulse OTDRs send pulses down fiber optic networks from one end of the fiber, displaying a trace and reporting all detected events such as splices, connectors, macrobends and fiber ends and breaks. The total fiber length is reported along with name, location, loss and reflectance of detected events. The intuitive keypad design features integrated shortcut keys designed for quickly positioning and analysing events. Another feature of this unit is the Live Optical Signal Detect Function, which tests if the fiber is live before sending the pulse, this can effectively prevent accidental damage to the OTDR and attached communication equipment.
-
Product
High Power Devices
-
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
-
Product
Single Shot Third-order Cross- Correlator
Rincon SS
-
Specifically developed for measuring a wide array of output parameters from ultrafast laser systems including: contrast ratio of laser pulses, determining pulse pedestal, pre- and post-pulses, and amplified spontaneous emission in femtosecond systems.
-
Product
DC Vibration Unit Tester
BK2116
-
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
