Product

Conductivity Type Tester

HS-HCTT

-

HenergySolar

HS-HCTT - HenergySolar

It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.

Product

Probes

Hygro-i Series

-

Tramex Ltd.

Hygro-i Series - Tramex Ltd.

The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.

Product

SICRAM Module Pressure Probes

PP471

-

Senseca

PP471 - Senseca

Module to connect pressure measuring instruments to pressure probes.

Product

Ultra Fast Flexible Implantable Microprobe

IT-23

-

Physitemp Instruments

IT-23 - Physitemp Instruments

IT-23 Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Time constant 0.005 seconds. Tissue Implantable with a 23 gauge needle (supplied). Fairly fragile. Sensor wires are twisted TFE Teflon™ insulated. Maximum Temperature 150°C. Isolated. Probe diameter .011", 3 foot lead.

Product

Magnetic Probing Systems

MPS-C-300 and MPS-C-350

-

MicroXact, Inc.

MPS-C-300 and MPS-C-350 - MicroXact, Inc.

MicroXact’s truly unique patent-pending design enables wafer-level testing of spintronic devices, nanoscale electronics and many other materials and devices where magnetic fields are required for accurate test and measurement.

Product

Immersion Probe

TP49A.I

-

Senseca

TP49A.I - Senseca

Immersion probe with SICRAM module, Pt100 sensor.

Product

Temperature Probe for Outdoor

TP32MT…

-

Senseca

TP32MT… - Senseca

Series of Pt100 1/3 DIN 4-wire or T-type thermocouple temperature probes for outdoor/environmental measurements.

Product

Probe Card

VersaTile™

-

Celadon

VersaTile™ - Celadon

Celadon has reduced the size of a probe card to 28mm with the VersaTile™ with Advanced Cantilever™ technology. The VersaTile™ with Advanced Cantilever™ technology can fit on a conventional 3-hole mount probe positioner for single site probing. The same VersaTile™ with Advanced Cantilever™ technology can be used in a 300mm VersaPlate™ for multi-site probing.

Product

Active Differential Probe

DF-600

-

Link Instruments

DF-600 - Link Instruments

The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.

Product

Flexible Implantable Microprobe

IT-1E

-

Physitemp Instruments

IT-1E - Physitemp Instruments

IT-1E Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Similar to our most popular IT-18 microprobe but the sensor bead is exposed, resulting in the same ultra-fast response time of the IT-23 but with the Teflon™ sheath strength of the IT-18. Time constant 0.005 seconds. Tissue Implantable with a 18 gauge needle (supplied). Rather fragile at tip. Coated in Teflon™. Maximum Temperature 150°C. Isolated. Probe tip diameter .011", sheath diameter .025'' . 3 foot lead.

Product

ResMap or DualMap Manual Load

-

Creative Design Engineering, Inc.

Creative Design Engineering, Inc.

*Type: Table Top*Wafer load: Manual *Wafer size: 2" to 8", 152mm x 152mm*Mini Environment: N/A*Probe Changer: N/A*Aligner: N/A*Size: 12" x 19" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic

Product

Integrated Balun Probes

-

Picoprobe

Picoprobe

This is an example of a 900 MHz Integrated Balun Probe. It incorporates a 50 ohm unbalanced to 200 ohm balanced differential transformer. The probe can be built with or without a center tapped ground needle and may also incorporate DC bias through the differential pair or via separate needle contacts.

Product

MPA50 ICT Probes

-

Merica Technology Ltd

Merica Technology Ltd

MPA50 Series ICT Probes

Product

Test Hook Probe

CX-17

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-17 - Shenzhen Chuangxin Instruments Co., Ltd.

Test Hook Probe Test Hook Probe is strickly designed according to IEC60065.

Product

Battery Impedance Meter

-

Alpha Lab, Inc.

Alpha Lab, Inc.

Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.

Product

Crack Testing

STATOGRAPH® Product Family

-

Foerster Instruments, Incorporated

STATOGRAPH® Product Family - Foerster Instruments, Incorporated

The STATOGRAPH product family is used for testing surface cracks with the help of eddy current sensors. Eddy current testing for material cracks requires the appropriate evaluation electronics and probes adapted to the testing task. Depending on the test situation and test object, the STATOGRAPH family of test instruments offers the right system for this purpose.

Product

Serial Probes

-

Nexus Technology, Inc.

Nexus Technology, Inc.

Probing a SRIO 1 or 2 serial bus at the transmit or receive end point provides the optimal signal for analysis. Single channel probes are designed to attach at that point providing flexibility for different channel widths.

Product

Probes And Cables

-

Santa Barbara Infrared, Inc.

Santa Barbara Infrared, Inc.

The iProbe is an intelligent temperature sensor that can be calibrated independently of SBIR’s blackbody systems or 104i precision thermometers. These ultra-stable, highly responsive iProbes are used to provide long term accuracy and repeatability of under 0.010°C. Each iProbe incorporates onboard flash memory that allows all calibration constants and calibration date information to be stored independently of the blackbody or thermometer system. This allows iProbes to be exchanged for use on a blackbody or thermometer without any loss in stability or accuracy. To re-calibrate a system you need only exchange the current iProbe with a recently calibrated one. No special equipment is required and there is no down time in the test area.

Product

Leak Detectors

-

Kane International Ltd

Kane International Ltd

High sensitivity setting locates R134A leaks to 3gm/yearFlexible gooseneck probeEasy one handed operationAudible & visual indicatorsRubber sleeve protects detector & probe

Product

Current Probe

PA-699

-

PINTEK Electronics

PA-699 - PINTEK Electronics

*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability

Product

Micropositioner

MP-40

-

Korima, Inc.

MP-40 - Korima, Inc.

Engineered for highly demanding probing needs, the Korima Model MP-40 Micropositioner is precision-built for micropositioning to meet ever smaller industry standards. Featuring linear motion on all three axes, the MP-40 provides precise control for sub-micron probing.