-
Product
68 Pin VHDCI Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
PRO Test Lead Kit
142
-
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
Product
E-Series Average Power Sensor
E9301A
-
Measure the average power of all modulation formats Wide dynamic range (-60 dBm to +20 dBm) and frequency range 10 MHz to 6 GHzHigh maximum power specification Low SWR for reducing mismatch uncertainty Calibration factors linearity and temperative compensation data stored in EEPROM Fast measurement speeds (up to 400 readings per second with the Keysight E4416A)Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Additional Products: 100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To 100-Pin
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
-
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
Product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - XMC
Model 71841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
FMC-LPC I/O Module
FM191
-
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-02
-
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
C Series Serial Interface Module
-
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
-
Product
Databus-to-Network Interfaces
OBB2
-
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
LVDT I/O Cards
IB
-
Computer Conversions Corporation
The "IB Series" product line are full size IBM PC/AT+ and ISA 2.01 compatible synchro, resolver, and LVDT I/O cards, and resolver-sensor card sets used as absolute encoder systems.
-
Product
Switched Amplifier With Analog Detector Output
-
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
Product
Tower Light Monitor
1750-TLM
-
Designed with the Broadcaster in mind the 1750-TLM provides built in flexibility to simplify even the most complicated installations. It can even alarm for single bulb failures on towers with Beacons and Obstruction lights on a single circuit. Status oututs eliminate the worry of operator interpretation and provide definitive Good-Bad indications for the operator and your logging equipment. Don’t let tower light failures expose you to increased liability, the 1750-TLM is compatible with most existing control equipment and may well provide your best return on investment this year!
-
Product
Moisture Analyzer
2850
-
Establishing a new standard for clean gas moisture analyzers, the 2850 provides exceptional performance, with virtually no interferences, multi-gas compatibility, and on-board measurement verification. The 2850 uses the most accurate trace moisture measurement technology available to deliver an ultrafast response to both increasing and decreasing moisture levels.
-
Product
S_A_Relay Card
-
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
Product
Battery Extra Load Units
BXL Series
-
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
-
Product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
-
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
-
Product
PCI Card
EXC-4000PCI/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M4K1553PxS module is NOT compatible to the M4K1553MCH module.The EXC-4000PCI/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
Mud Cake Friction Coefficient Tester
NZ-3A
-
Zhengzhou Nanbei Instrument Equipment Co. Ltd
With the development of drilling technology, special technology wells, directional wells, cluster wells do more and more. Lubricating performance requirements of the drilling fluid is also increasing, the processing agent for drilling fluid lubricant is also increasing year by year. Differences in the quality of the lubricant, together with a reasonable need for compatibility, we need an instrument to evaluate.
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
Flexible and Modular T11 Processor
ADwin-Pro II
-
The ADwin-Pro II system is the successor of the ADwin-Pro. The new system is equipped with a considerably faster T11 processor and transfers data 10 times faster with the new Pro II bus. At the same time the integrated ADwin Pro bus guarantees the compatibility with older modules still in use
-
Product
Industrial Serial GSM Modem
ENVIROMUX-GSM-IND
-
Sends SMS messages to a pager or cell phone when a sensor goes out of range of a configurable threshold. SIM card supporting SMS messaging required (not included). Ideal for harsh environments and high temperatures up to 149°F (65°C). GSM/GPRS/EDGE 850/900/1800/1900 MHz. AT command compatible. Dimensions: 3.58x2.28x0.87 in (91x58x22 mm). Operating temperature: -13 to 149°F (-25 to 65°C). Operating humidity: up to 95% non-condensing RH. Regulatory approvals: CE, C-Tick. Compatible with ENVIROMUX-SEMS-16(U).
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
Node.js® platform
N|Solid™
-
N|Solid is a fully compatible Node.js runtime that has been enhanced to address the needs of the enterprise. Rapidly resolve performance problems. Protect customer data from vulnerable packages and unauthorized code. Drive performance and operational efficiency at scale.
-
Product
PCIe LVDS Digital Waveform Acquisition - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7735-X8
-
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
Open-Frame Collet Socket with Solder Tail Pins
Series 518
-
Open Frame Collet Sockets with Solder Tail Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. Choose from several pin styles. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
-
Product
Single Front Slot + Single Rear Slot Universal PCI to PCMCIA Adapter
P416
-
The P416 addresses the need to have front access to a PCMCIA slot for use with cards like Flash media, or Finger Print recognition, while also having a rear slot for cards that are less frequently swapped, like Wireless LAN or Bluetooth. The rear slot is 32-bit capable meaning it supports CardBus cards which makes it forward compatible with some of the newer high speed Wireless LAN standards like 802.11a and 11g.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-01
-
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
