-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Hi-Q W-Band Ultra Low Phase Noise Analyzer
OE8000W
-
HI-Q® W-Band phase noise test system utilizesmicrowave photonics techniques for automatedmeasurement of ultra-low phase noise W-bandoscillators.
-
Product
Narrow Band Multiplier
-
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
S-Band Planar Antennas with 8 dBi Gain
LS-08-PS
-
The Lumistar LS-08-PS S-Band Planar Antenna is the ideal companion to the LS-25/27/28 Series Receivers to provide a low cost receiving system with extremely high performance. This small, lightweight antenna is available in various polarizations. The Standard version offers the quickest delivery, but other versions including ones with Polarization Diversity. Combining (dual linear with ±45 slant range) is also available.
-
Product
RF Taps
-
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
Product
Detector Mount
DMXE
-
The DMXE Detector Mounts are broadband devices designed for operation in millimeter wave range. The Detectors are optimized for broadband performance and are used in mm-wave test setups to detect, monitor and measure modulated signals.The DMXE Detector Mounts use Schottky Barrier packaged diodes and are provided in five waveguide bands between 33 GHz and 225 GHz.
-
Product
C-Band Single Channel FGA Fixed Gain EDFA
HSA4400 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4400 series is a fixed gain EDFA which is designed specifically for single wavelength optic transmission system. The EDFA adopts excellent optical performance and advanced electric transient control technology, which can efficiently restrain the input optical power change that caused by amplifier, create large transient change of output optical power, so that to protect optical detector and other optical devices in high-speed network.
-
Product
Schottky Diodes
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
(100×130×19mm) C-Band DWDM Pre-Amplifier EDFA Module
WPA4300-FM04
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WPA4300-FM04 series with 100 × 130 × 19mm Compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 wave wave DWDM system applications.
-
Product
Narrow Band Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Narrowband (11GHz-17GHz) tunable clock phase shifterDelay adjustment range of 140psExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the phase adjustment tuning portsIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with 800mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 0.91WFabricated in SiGe for high performance, yield, and reliabilityStandard MLF/QFN 24-pin package
-
Product
Waveguide Power Dividers
-
2-way power divider that operates from 220 to 330 GHz. The power divider offers a typical insertion loss of 2.3 dB and typical isolation of 20 dB. All ports are well-balanced and in-phase for power dividing or combining applications across the band. The power divider is configured as a right-angle package with WR-03 waveguides and UG-387/U-M anti-cocking flanges at all ports.
-
Product
IR-Emitters
-
Our IR emitters are almost exclusively used in chemical analysis. There is a distinction to be made between broadband and narrow-band emitters. Planck’s emitters are broadbanded, whereas IR lasers are narrow banded.
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
Product
Millimeter Wave Antennas
-
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
UHF/RFID Power Divider Combiner 8-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2981
-
INSTOCK Wireless Components, Inc
PD2981 is a RoHS compliant, 8 way, wideband, 50 ohm, RF power divider, power combiner furnished with TNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 8 way power divider input rating tables for additional details.
-
Product
SSA Signal Source Analyzer, 10 MHz to 7 GHz, 26.5 GHz, or 110 GHz
E5052B
Signal Analyzer
RF Input frequency range: 10 MHz to 110 GHz Analysis offset frequency range: 1 Hz to 100 MHz Phase noise measurement with ultra low noise floor and a cross-correlation method Frequency transient capture range: up to 80 MHz in narrow band, up to 4.8 GHz in wide band
-
Product
AERINOS Sigfox IoT
-
Infinite Industrial Informatics Lt
Sigfox is a communication protocol that is used to read data from sensors through a fixed network of base stations. It works like a low cost “SMS” service. As an end-user, you only need to buy a subscription to connect to the data network operated by SIGFOX. Sigfox employs a proprietary Ultra Narrow Band (UNB) radio technology that enables communication using the Industrial, Scientific and Medical ISM radio band, which uses 868MHz in Europe and 902MHz in the US. It has the advantage of covering larger areas than other fixed local systems.The overall Sigfox network topology has been designed to provide a scalable, high-capacity network, with very low energy consumption, while maintaining a simple and easy to rollout star-based cell infrastructure. The density of the cells in the Sigfox network is based on an average range of about 30-50km in rural areas and in urban areas, where there are usually more obstructions and noise is greater, the range may be reduced to between 3 and 10km.According to the latest numbers, Sigfox has a nationwide live coverage in 6 countries and in 14 other countries it is deploying and rolling out ts network. By end 2018, the ambition is to cover 60 markets.
-
Product
K-Band Silicon SATCOM Rx Quad Core IC
AWS-0102
-
The AWS-0102 is a highly integrated silicon quad core IC intended for satellite communications applications. The device supports four dual polarization radiating elements with full programmable polarization flexibility. The device provides 22 dB of gain with a noise figure of 3.4 dB. Additional features include gain compensation over temperature and temperature reporting. The chip features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
All-standard All-band Modulator For USB-3
DTU-315
-
Modulation has never been so easy and so beautiful. The DTU-315 is a portable modulator for satellite, terrestrial and cable, all in a single device.A good fit for laptop or tablet, but convenient with desktops and server PCs too.
-
Product
Power Amplifier
MS 2011
-
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
Product
Systems Integration for Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
Product
IP67 DC Blocking Splitter Combiner
PD5143
-
INSTOCK Wireless Components, Inc
PD5143 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5043 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
O-Band Interleaver For 5G-PON Mux/DeMux
-
Optoplex has been the leading technology innovator and marker leader of optical interleavers for optical communications. • Technology and market leader of interleaver for optical communications• Dominant supplier of optical interleaver for global subsea network applications• 1st company of 25GHz interleaver • Proprietary Co-Packaged interleaver (Mux/DeMux)• Proprietary “Super” wide passband interleaver• A leading company of O- and E-band optical interleavers for 5G Mux/DeMux applications
-
Product
Millimeter-wave Operation With Frequency Extenders For P50xxA Streamline VNA
S97560B
Vector Network Analyzer
Configure an affordable millimeter-wave banded VNA using P50xxA Streamline USB VNAs with this software
-
Product
60 GHz Systems and Modules
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules and customer prototyping for system development. This 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development system makes it easy to design new products and applications in the emerging unlicensed millimeter wave ISM band.
-
Product
Amplitude Detectors with Isolators
-
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
-
Product
Digital Belt-Pack Transmitter
DBu
-
The DBu transmitter is a 4th generation design with specially developed, high-efficiency digital circuitry for extended operating time on two AA batteries. The transmitter can tune in coarse or fine steps across the UHF television band from 470 to 608 MHz (470-614 MHz for export versions), with a selectable output power of 25 or 50 mW. The pure digital architecture enables AES 256-CTR encryption for high-level security applications.
-
Product
Integrated 5G mmWave Test System
IQgig-5G
-
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
