-
Product
Electrophysiology
-
Burleigh's® microscope platforms, micromanipulators, and accessories provide leading edge stability and control for electrophysiology research. The Gibraltar® platform supports microscopes from popular third-party manufacturers such as Olympus, Zeiss, Nikon, and Leica, and our manual and motorized micromanipulator assemblies offer excellent control for patch clamping experiments.
-
Product
Phase Modulated Driver
-
The Phase Modulation Capable RF Driver / Stabilizer is an eight channel, two phase RF driver intended to drive devices such as the Harris H-401. The driver provides both amplitude and phase modulation capabilities in a single unit. The device can be operated in driver mode where the operator has full control over amplitude, frequency, and phase, or in stabilizer mode where the driver automatically adjusts the operating parameters based on optical feedback from an optical pick-off point.
-
Product
Single Frequency CW 532 NM Laser up to 18W
EQUINOX
-
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
Product
LGM-300 Lighting Glare Measurement System
-
Hangzhou Everfine Photo-E-Info Co., LTD
LGM-300 is for glare measurement and analysis of indoor and outdoor lighting scenes meets the measurement requirements of CIE, EN, GB standards with good measurement stability. The system is portable and can be widely used for on-site-glare measurement and analysis such as indoor lighting, road lighting, sports venues and regional lighting.
-
Product
AC Power Source
APS-7000 Series
-
AC Power Source APS-7000 Series, the advanced direct digital frequency synthesizer (DDS) waveform is used to achieve high frequency stability, good continuity and accurate measurement.
-
Product
Precision RTD Simulator
RTD Series
-
The RTD Series Precision RTD (Resistance Temperature Detector) Simulator provides a very broad-range of absolute resistance values that replace RTD's and thermocouples. Thermocouples present a resistance that depends on the temperature. The RTD simulator effectively replaces an RTD to test, analyze, and calibrate RTD measuring systems. The RTD Series simulator is a precision resistance source with excellent characteristics of accuracy, stability, temperature coefcient, and power coefcient. All these features serve to make it a laboratory resistance standard, exceeded in performance only by stand-alone standard resistors. The special design of the RTD Series provides absolute accuracy, and requires no zero resistance subtraction from any setting Special design of the RTD virtually eliminate zero resistance and switch contact variations, providing the specified absolute accuracy over the entire range.
-
Product
CO2/H2O Analyzer
LI-870
-
The LI-870 CO2/H2O Analyzer is a versatile analyzer for publication quality data that is simple to deploy, use, and maintain. A combination of precision and stability alongside a rugged and fieldable design makes it ideal for survey and long-term research focused on fluxes of soil CO2.
-
Product
19-Slot 3U PXI Chassis with AC
PXIS-2719A
Chassis
The ADLINK PXIS-2719A is a 3U PXI chassis with a series of advanced features:*An innovative cooling mechanism to deliver efficient and uniform heat dissipation*Superior stability within an extended temperature range*Intelligent chassis management that dynamically monitors and manages fan speed, system voltages, and internal temperature*Remote management via standard RS-232 monitoring port
-
Product
Cellular Jammers
-
Security Intelligence Technologies, Inc.
Our line of Cellular Jammers are designed with PLL Stabilization, an engineering feature that makes our digital cellular jammer unparalleled in performance. To jam cell phones using our Stabilized method, we have designed a directional jammer that is able to perform twice as better under difficult operating conditions.
-
Product
Drug Stability Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
If you want find complete details about Integrated drug stability test chamber, Drug stability test chamber, Chemical drug stability test chamber, New designed integrated drug chamber, Good quality integrated drug test chamber - China Sanwood Environmental Chambers Co., Ltd. The scientific method to create a drug for a long time to failure evaluation of stable temperature, humidity and light environment for pharmaceutical enterprises to accelerate drug test, long-term test, high humidity and strong light test, is the best choice for pharmaceutical companies and drug stability test program.
-
Product
4-20mA Output Inclinometer
LCF-2330
-
The LCF-2330 inclinometer series now includes a 4-20mA output signal option for applications that require long cable runs. This dual axis tilt sensor is fluid damped to minimize noise and vibration interference while also offering a sharp 1 µradian resolution. An internal temperature sensor is available and dual supply, ± 5 Vdc output is an option. The LCF-2330 is an excellent solution for rugged applications such as radar & antenna leveling, weapons platform leveling, barge and offshore platform control, deviation surveys, 2-axis machine tool leveling, bridge structural monitoring, submersible control feedback, offshore platform stability and manufacturing process equipment for the aerospace industry.
-
Product
Eddy Current Sensor
eddyNCDT 3001
-
The eddyNCDT 3001 is a new, efficient eddy current sensor whose compact dimensions have to date only been reserved for inductive sensors and proximity sensors. The temperature-compensated design provides high stability even in fluctuating ambient temperatures. The eddyNCDT 3001 comes with integrated electronics, offering an outstanding price/performance ratio and easy operation. The eddyNCDT 3001 eddy current sensor is ideally suited to OEM integration and machine building applications. The sensor is factory-calibrated for ferromagnetic and non-ferromagnetic materials, which eliminates the need for field calibration of the sensor. The eddyNCDT 3001 is available with connector or with integrated cable. A robust design combined with the eddy current measuring principle enables measurements in harsh industrial environments (oil, pressure, dirt). In addition, the eddyNCDT 3001 is suitable for offshore/marine applications (salt water).
-
Product
Power Supply
-
The Power Supply Systems are the heart of any experiment. They provide the High voltage and Low voltage required by the detectors and by the related front-end electronics. The quality of the power supply is critical to obtain the best performance from the set-up. The sensibility of modern detectors, in fact, make them susceptible to any even small variation in the power supply, and so features like low Noise, low Ripple and high stability become essential in the design of a performing power supply system. Strong of 40 years of collaboration with the most important research labs worldwide CAEN offers today sophisticated High Voltage Power Supply and Low Voltage Power Supply Systems. The demonstration of this successful long-standing tradition is the “CMS Crystal Award 2009” that CAEN received for the development and production of the power system for the CMS tracker. CAEN offers a wide selection of Power Supplies in different form factors and standards:- For smaller set-ups Standalone or modular (NIM / VME) products or are the ideal fit.- For bigger set-ups, where a high number of High voltages and Low voltages is required, the Mainframe Systems and Boards (up to 48 channels/board, up to 768 channels in a single Mainframe) are the most recommended.
-
Product
Ultra-High Stability DC Power Supply
62075H-30N
-
Chroma Systems Solutions, Inc.
Chroma’s new 62075H-30N ultra-high stability DC power supply offers many unique advantages for magnet power supply systems in synchrotron applications. These advantages include an excellent current stability of 1.25mA/0.5 hour and 2.5mA/8 hour, extremely low current ripple of 2.5mA, current reproducible within 10mA, precision setting and readback of output current via 20 bit DAC/24 bit ADC.
-
Product
Resistance Temperature Sensors
-
Watlow Electric Manufacturing Company
These sensors are suited for applications where accuracy and stability are essential for proper control in applications that operate at or below 1200°F (650C).
-
Product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
-
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
Product
Climate Chamber
ICH
-
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
Product
Optical Signal Test Set
OST
-
The Optical Signal Test Set (OSTS) combines a state of the art optical power meter, a variable attenuator, and a high stability laser source. The unit is able to measure optical signals below -100dBm with 0.001dB resolution at a fraction of the size, power, and cost of competing solutions. Other features include data logging, programmable filtering, and auto calibration. Its small shielded ruggedized package, USB/power interface, and low cost make this unit perfect for lab use or for integration into larger systems.
-
Product
Light Source
UVF-204S
-
This is the ultra compact and light weight high power unit fully utilizing characteristics of the high stability and long life 200watt mercury xenon lamp.
-
Product
Analytical Balaneces
AT-R Series
-
Basic Model with Improved Convenience.*Freely set responsiveness or stability*Connect with a computer via USB or RS232C*Perform stable measurements in combination with an ionizer
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
Flow Management
HR7100
-
HighReach Measuring & Controlling System Co.,Ltd
HR7100 series intelligent electromagnetic flowmeter is a fully intelligent flowmeter developed and developed by our company using the most advanced technology at home and abroad. It has the characteristics of high measurement accuracy, high reliability, good stability and long service life. Pay attention to every aspect In the process of designing product structure, material selection, manufacturing process, production assembly and factory testing. We have a water tower of up to 35m as a steady-state flow regulator, as well as a professional electromagnetic flowmeter production equipment line. Designed and developed large-scale production software and hardware for electromagnetic flowmeters to ensure long-term high quality.The product is designed with Chinese and English liquid crystal display with wide backlight and full-featured function. It is intuitive to display, easy to operate and use, and can reduce the trouble of on-site installation and maintenance. Widely used in petroleum, Chemical, metallurgy, water supply and drainage, steel, coal, paper, food, textile, environmental protection and other industrial sectors and municipal management, water conservancy construction and other fields.
-
Product
Super Quality Fiber
-
Panasonic Industrial Devices Sales Company of America
These Super Quality Fibers are designed with an extremely small beam axis curvature and gap which results in a high stability of light intensity. When combined with the FX-500 Amplifiers, the stability of light intensity is improved up to 4 times compared to traditional Fibers.
-
Product
Ultrafast Transient Absorption Spectrometer
Harpia-TA
-
The transient absorption spectrometer HARPIA offers a sleek and compact design together with intuitive user experience and easy day-to-day maintenance meeting the needs of today's scientific world. Adhering to the standards raised by the OPRHEUS line of devices, the entire spectroscopic system is contained in a single monolithic aluminum casing that inherently ensures excellent optical stability and minimal optical path for the interacting beams. HARPIA can be easily integrated with both PHAROS / ORPHEUS and Ti:Sa / TOPAS laser systems. HARPIA features market leading characteristics such as 10-5 resolvable signals along with other unique properties such as the ability to work at high repetition rates (up to 1 MHz) when used with PHAROS / ORPHEUS system. High repetition rate allows measuring transient absorption dynamics while exciting the samples with extremely low pulse energies up to several nanojoules.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Linear Rail Systems
-
Haydon Kerk offers both motorized and non-motorized linear rails, guides and splines that deliver enhanced system stability, high positional accuracy, low friction and long life for a variety of linear motion applications.
-
Product
Quantum Accelerometer
-
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
Product
Dual 16x4 1-Pole High-Density PXI Matrix Module
40-520-404
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
5KVA to 100KVA Industrial UPS (3Ø – 1Ø)
NSP Series 5KVA to 100KVA
-
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
Product
Handheld Water Quality Meters
LAQUA WQ-330-K
-
Triple channel. Large colour graphic LCD screen (70 x 52 mm) with backlight. Built-in foldable meter stand. IP67 waterproof and dustproof. Battery and USB powered. Eco-friendly, shock-proof, scratch-resistant, and non-slip. Built-in sensor holders. Efficient sensor locking mechanism. Sensor's LED light as reading stability indicator. No sensor adapter needed for attaching multiple sensors together. Compatible with conventional electrodes having BNC and phono connectors and long cables. Sensor status indicator. Temperature sensor indicator. °C & °F temperature units. Sample ID setting. Detailed calibration data. Auto stable, Auto hold, and Real time measurement modes. Customizable meter kit - up to 35 meter-sensor kit combinations. Hands-free testing. Ergonomic design. Multi-language options. Versatile channel and adaptive display. Up to 3 simultaneous calibrations and measurements. Automatic sensor recognition function. Data transfer via USB or wireless communication. Printer communication. 3 years meter warranty.
