Analog Output Modules
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
8/16-CH 16-Bit Analog Output Modules
cPCI-6208/6216 Series
Analog Output Module
- PICMG 2.0 Rev 2.1- 16-bit D/A resolution- 16-CH voltage on 6216V- 8-CH voltage outputs on 6208A and 6208V- 8-CH current outputs on 6208A- Bipolar analog output range- 4-CH TTL DI and 4-CH TTL DO- Rear I/O available
-
Product
Analog Output Modules
D3000/4000
-
The DGH D3000/4000 series are complete computer-to analog output modules. They communicate, in ASCII, with RS-232 and RS-485 serial ports. Simple ASCII commands are used to control a 12-bit DAC (Digital-to-Analog Converter) which is scaled to commonly used current and voltage ranges.
-
Product
PXI-6711, 12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module
777794-01
Analog Output Module
12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6711 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6711 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
Analog Output Module
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6733 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Analog Output Module, 16-bit D/A
IP230A
-
Jumper-selectable output ranges give you the choice of unipolar or bipolar voltage output. And for greater flexibility, the IP230A module accepts conversion start triggers from software commands, or from external sources for synchronization to specific events.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
sbRIO-9263 , Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
780876-01
Voltage Output Module
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The sbRIO‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The sbRIO‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-02
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
779012-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
Voltage Output Module
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
Product
4-CH Analog Output Module
HSL-AO4-U
Analog Output Module
The HSL-AO4 offers four analog output channels with a high drive capacity based on the HSL bus. The HSL-AO4 also features 16-bit resolution and offset/gain calibration to minimize the power-on 0-voltage drift to meet precise analog output requirements.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
32 Channel PWM Generator Module with Analog Outputs
DP-VME-5835
-
DP- VME-5835 is a Pulse Width Modulator module with analog outputs. This module has thirty two Pulse Width Modulated output channels and four analog output channels.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXIe-6739 , 16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module
783801-01
Analog Output Module
16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module—The PXIe‑6739 is a high-density analog output module. The device is ideal for applications such as stimulus-response tests and open-loop simulations at high densities. You can achieve the maximum sample rate if using up to 16 channels, where each channel is on a separate bank. The PXIe‑6739 also includes 20 digital I/O lines, four counter/timers, digital triggering, and advanced timing to meet a wide range of application requirements. Its digital triggering and PXI Express synchronization capabilities allow it to be coupled with additional data acquisition, motion, and vision products to create highly custom measurement solutions to test innovative designs.
-
Product
Isolated D/A Converter 8 Channel, 250kSa/s
OTP2 module no.187
-
The PXIe‑4322 is a channel-isolated analog output module with built-in signal conditioning. The module provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters in one device, the PXIe‑4322 isolated analog output module offers smaller dimensions and higher measurement performance. In current mode, the module operates in all four quadrants, allowing current to be drawn and sourced. Thanks to isolation and outputs for higher voltages and currents, the module is particularly suitable for applications in the automotive sector.
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
Product
Analog I/O module with 16 differential analog output channels
IO107
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
Analog Output Module, 16-bit D/A
IP231
-
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 12 Channel
43-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Control Unit
MX 256
-
Teledyne Gas & Flame Detection
The MX 256 is a digital control unit intended for the detection and measurement of gases present in the atmosphere and more generally for the processing of any digital signal from digital sensors (OLCT 10N types), relay module, analog output module, logic input module. Thanks to its new option, an industrial controller module or remote HMI, it is possible to add analog input modules for sensor-transmitter connection (4-20 mA) and / or relay modules, this allows to not only extend the capacities but also to have event recordings (Location, Alarms,.....) and to have access to the data via the embedded web page.
-
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Ruggedized Field Deployable Tester
PUMA
-
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
