PXI Interfaces
-
Product
C Series PROFINET Interface Module
Interface Module
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
Product
USB 1553 and ARINC Appliance
USB-MA4
USB Interface
The industry’s first USB 3.0 SuperSpeed Multi-channel MIL-STD-1553 and/or ARINC-429 appliance!1-2 1553 Dual Redundant Channelsand/or 8 ARINC-429 Channels (4 RX/TX and 4 RX)Supports ARINC-717 (shared with 429 channels)
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
sbRIO-9853, Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module
780923-01
CAN Interface
Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module—The sbRIO‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA‑based applications with the NI‑RIO driver on CompactRIO. These modules are ideal for low-level FPGA‑based control and triggering applications that are programmed using the NI LabVIEW FPGA Module. These modules also are ideal for byte-level manipulation of CAN frames in the NI LabVIEW FPGA Module. The sbRIO‑9853 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
PXI High Density MUX BRIC, 4-Chan, 160-Pole
40-570-014
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
CAN Interface
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Low-Profile High-Performance IEEE488 GPIB Interface for PCI Bus
LPCI-3488A
Interface
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
Product
FPGA PXI Card With 80 Channel LVDS Buffer Module
GX3611
FPGA PXI Card
The GX3611 is a 3U PXI FPGA card with 80, LVDS channels and is comprised of the GX3500 PXI FPGA card and the GX3511 expansion card.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
PXIe-6594, FlexRIO High-speed Serial Module (28 Gbps), KU15P
786939-01
Serial Interface
PXIe, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument. - The PXIe-6594 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale+ FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe-6594 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
Low-profile High-Performance IEEE488 GPIB Interface for PCIe Bus
LPCIe-3488A
Interface
The IEEE-488 standard, also known as GPIB, is a bus interface that connects instruments with a computer to form an ATE system. Today, GPIB is still the most popular interface between computer and instruments. ADLINK"s USB-3488A, LPCI-3488A and LPCIe-3488A controller interface cards are fully compatible with the IEEE-488.2 instrumentation control and communication standard and are capable of controlling up to 14 stand-alone instruments via IEEE-488 cables. The USB-3488A, LPCI-3488A and LPCIe-3488A are designed to meet the requirements of high performance and maximum programming portability.
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
Interface Card
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
Interface Module
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
Serial Interface
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXIe System Module: Single Port (x8), Gen 3
M9022A
PXI Express Module
The M9022A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The module can also be used with an M9037A PXIe embedded controller to interconnect two chassis in a multi-chassis system.
-
Product
PCIe-8430, PCI Express, 16-Port, RS232 Serial Interface Device
780591-02
Serial Interface
The PCIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as … standard COM ports for compatibility with programs that use serial communications.
-
Product
GPIB User Installable Interface Module
EL34GPBU
Interface Module
EL34GPBU GPIB user-installable interface (SCPI-1999, IEEE 488.2) module adds a GPIB interface to your EL30000 Series bench electronic load.
-
Product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Interface Module
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
Product
Intelligent ARINC Interface Module
M4K717
Interface Module
The M4K717 is an intelligent ARINC 717 interface module for the multiprotocol Excalibur 4000 family of carrier boards.The module supports two ARINC 717 receive channels and two transmit channels.In transmit mode, the module sends the four subframes from a pre-defined buffer in dual-port RAM.In receive mode, the module stores all subframes with status and Time Tag information appended to each subframe.The M4K717 comes complete with C-driver software library including the source code.
-
Product
Digital/Pattern/PE Card
PEMU32
Interface Card
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
Product
AIM Interface Modules
Interface Module
AIM’s innovative, unique and successful ‘Common Core’ hardware design set new standards for onboard intelligence and performance when introduced to the market in 1998. Since then, further generations and evolutions of the Common Core approach have been introduced, offering improved performance, higher channel density, lower power consumption, the migration to smaller form factors as well as the support of new avionics bus and network communication standards.
-
Product
PMC Interface Card
CPCIC-MA4
Interface Module
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
PCIe-8430, PCI Express, 8-Port, RS232 Serial Interface Device
780591-01
Serial Interface
The PCIe‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
Product
Portable Avionics Interfaces for USB 2.0
Interface
These versatile interfaces are suitable for a wide range of applications in the lab and in the field. They support maximum data throughput on all channels and have a large 32 MB built-in memory. All power necessary for operation is provided via the single USB port. Plug and Play and Hot Swap features make them easy to install and move between computers.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
4x 3U OpenVPX MOSA Actuator Interface Unit
SIU34-AIUVARM-01
Actuator Interface Unit
SIU34-AIUVARM-01 is a Modular Open Systems Approach (MOSA) DO-178C & DO-254 Certifiable Actuator Interface Units (AIU) with low power high performance OpenVPX Xilinx UltraScale+ SBC with Quad Core ARM Cortex -A53, 8 GB DDR4 SDRAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet, USB 3.0, FIPS-140-3 Level 3 Cyber Security, and Single Event Upset support.
-
Product
PCI Express Host Interface SSD/Drive Decode Support
Interface
Teledyne LeCroy provides NVM Express, SATA Express and SCSI Express protocol decoding, analysis and test equipment to SSD storage companies worldwide. It works closely with the following organizations providing equipment to its members and conformance programs.
