D-Sub
D-Subminature Connector Also known as: DSub
-
Product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
-
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
Product
Cable Assembly, Receiver, 36", TriPaddle, to 25 Pin Female D-Sub
540014010201
-
Cable Assembly, Receiver, 36", TriPaddle, to 25 Pin Female D-Sub
-
Product
CANBus Communication
PISO-CAN400U-T
-
The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suit for networking "intelligent" devices as well as sensors and actuators within a system or sub-system. In CAN networks, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As standalone CAN controller, PISO-CAN400/CAN200 can represents an economic solution of an active CAN board. It has two or four independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PISO-CAN400/CAN200 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in a 5V PCI slot and supported truly “Plug & play”.
-
Product
DB - BNC Breakout Trigger Cable
149055-0R2
-
14-Pin D-SUB Male to 6 1-Pin BNC Female, 20 cm, Breakout Trigger Cable. The PXI Chassis Trigger Cable you send and receive signals between compatible PXI Chassis that feature programmable function input (PFI) lines. You can use the PXI Chassis Trigger Cable to control devices or to set up or perform triggered functions such as continuous data acquisition.
-
Product
PCI Express Digital I/O Boards
PEX-1002H
-
PCI Express, 32-ch, 12-bit, 44 kS/s High Gain Multi-function DAQ Board. Includes CA-4002 D-Sub connector
-
Product
General Purpose Switches
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
160-Pin DIN Female To 4 50-Pin D-SUB Female Switch Cable
782417-03
-
The SH160DIN-D-sub helps you connect to the PXI-2510 PXI Signal Insertion Switch Module or compatible PXI Relay Modules. You can use this cable to facilitate signal routing between instruments and devices-under-test (DUT).
-
Product
PCI Daughter Boards
DB-24SSR/D/DIN (DB-24SSR/D with DIN-Rail Mounting)
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Cable Assembly, Receiver, 48", TriPaddle, 50 Pin FML DSub
540111030603
-
Cable Assembly, Receiver, 48", TriPaddle, 50 Pin FML DSub.
-
Product
3-m, 78-pin Dsub Cable
Y1138A
-
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
Product
18" Ribbon Cable
RCONM50-D25-2
-
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the PCI carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
Product
8-Pin D-SUB Female To 8-Pin Bare Wire Male Switch Cable
781092-02
-
The DB8F-Bare Wire-40A helps you connect to the PXI-2512, PXIe-2512, PXI-2514, and PXIe-2514 PXI Signal Insertion Switch Modules. You can use this cable to facilitate signal routing between instruments and devices-under-test (DUT).
-
Product
Cable Assembly, Receiver, 48", QuadraPaddle, 78-Pin ML D-Sub
540116020640
-
Cable Assembly, Receiver, 48", QuadraPaddle, 78-Pin ML D-Sub.
-
Product
50-Pin D-Type Connector, Right Angle PCB
40-963-050-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
DB37 Cable
PCL-10137
-
Double-shielded cable with 37-pin D-sub connectorsD-Sub 37 pin male, Blue x 2Tinned and strand copper wire with drain wire x 1Aluminum/Mylar foil and braided copper double-shielded cableIsolated P.V.C. jacketUL20397 approvedIvory Color
-
Product
R37F-37M-1, 37-pin Female to Male Ribbon I/O Cable, 1m
779195-01
-
37-Pin Male IDC to 37-Pin Female D-SUB, I/O Ribbon Cable - The R37-37 is an unshielded ribbon cable for use with PC-based PC-based measurement and control systems featuring CompactDAQ Chassis.
-
Product
200-Pin Male OR 4X50-Pin To 200-Pin, 60 VDC LFH Switch Cable
783139-02
-
The LFH200 cable provides connectivity to the NI PXI-2569, PXI-2570, PXI-2571, PXI-2575, SCXI-1169, and SCXI-1175 switch modules. There are three different options for this cable. All three options have a 200-Pin, Male LFH front end connection. Each option has a different back end connection. The first option has a 200-Pin, Male Bare Wire back end connection. This option is specifically suited for the PXI-2569/70/71 and SCXI-1169. You can use the unterminated ends for custom wiring needs, twisting the channel and common terminals of the PXI-2569 and SCXI-1169 to reduce crosstalk. The second option has 4 50-Pin, Female D-Sub back end connections. This option is specifically suited for the PXI-2569/70/71 and SCXI-1169. The second option uses the same twisted-pair configuration (CH-Com Twisted) but offers 50-pin D-Sub connectivity. The third option also has 4 50-Pin, Female D-Sub back end connections, but it twists the ch+ and ch- terminals (CH-CH Twisted) when used in a 2-wire configuration. This option is specifically suited for the PXI-2575 and SCXI-1175.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 78-Pin Female D-Sub
540034010203
-
Cable Assembly, Receiver, TriPaddle, 36", 78-Pin Female D-Sub
-
Product
CANBus Communication
PCM-CAN200-D
-
PCM-CAN200 can represent a CAN solution on a high quality PCI104/PC104+ hardware in industrial environment compliant with CAN 2.0A and CAN 2.0B specification. It has 2 independent CAN bus communication ports with 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications.
-
Product
CABLE ASSY, Type SH100-100-FLEX, 2 m
185095-02
-
The SH100M-100M Flex Cable, sometimes referred to as SH100-100-F, connects NI digital I/O devices to 100-pin accessories with D-SUB connectors. The SH100M-100M Flex Cable is offered in different lengths.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
-
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
-
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
-
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
Product
Cable Assy, Type SH100-100-Flex, 1 m
185095-01
-
The SH100M-100M Flex Cable, sometimes referred to as SH100-100-F, connects NI digital I/O devices to 100-pin accessories with D-SUB connectors. The SH100M-100M Flex Cable is offered in different lengths.
-
Product
4 X RS232/422/485, 2 X RS422/485, 8-Bit GPIO
MIOe-210
-
Full serial port: 4 x RS232 / 422 / 485, 2 x RS422 / 485±15kV ESD protectionOptional D-SUB connector or internal connectorProgrammable 8-bit GPIO interface
-
Product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
-
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
Product
PCI Daughter Boards
DB-24POR/D/DIN (D-Sub cable and DIN-Rail mounting kit)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
Board Accessories
DN-37A (with Din Rail Mount and Male-Female D-Sub Cable)
-
DN-37 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with a 37-Pin I/O Connector and 37-pin CA-3710 cable.
-
Product
Solder Cup Connector Kit
Y1140A
-
Used to build custom cables for 34922, 34924 – 78-pin Dsub female – 60 V
-
Product
PXI Programmable Resistor Module
-
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
