Shock
A shock test transmits kinetic or thermal energy into a UUT in a relatively short interval in a controlled enviroment.
See Also: Thermal Shock, Vibration
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
3U VPX Board
VP32004
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32004 is a high-performance PC-based 3U VPX processor board developed by Linkedhope®. It supports 3rd Gen Intel Core series processor and Intel QM77 chipset. It supports up to 16GB of on-board DDR3 ECC memory and supports mSATA SSD. In order to ensure that VP32004 works stably in a strong shock and vibration environment. VP32004 provides rich I/O interface, including 2x SATA III channels, 2x 1000 Base-BX/T, 1x RS232 front debug serial port, 3x RS232/422/485 interfaces (BIOS configurable), 4x USB2.0 interface, 1x USB3.0 interface, 1x Mini-DisplayPort display interface, 1x rear VGA display interface, 1x PS/2 interface.The board provides a flexible PCIe bus interface to the backplane that supports multiple configurations and can be configured as 1 x8, 2 x4, 4 x2 PCIe. This feature makes it suitable for both distributed and centralized switching systems.
-
Product
Solid State Relay Products
-
DARE Electronics? solid state relays incorporate advanced microelectronic hybrid technology and are available from low level to 50 amps. Solid state relays have distinct advantages over electro-mechanical devices including: no contact bounce, arcing or flashing; immunity to contact contamination and oxide formation in dry or normally open circuits; and immunity to shock and vibration thus preventing unwanted contact closures
-
Product
High Voltage Tester
-
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
Product
Special Application
-
Columbia Research Laboratories
This group of Piezoelectric Accelerometers have been specifically designed to meet Columbia Research Labs customers "special" needs. Whether it be our model 876 designed for use in extremely cold temperatures (-400°F) or our model 378-HT-1XP, designed with an extremely rugged housing for prolonged use in adverse industrial environments of shock, vibration, temperature, humidity and excessive oil, that can withstand temperatures of 700°F. We would be happy to see this list of sensors grow to meet your needs. Please call us so we can make something "special" for you.
-
Product
ZZ Power Booster 1200V/3000V
ZZ Booster-Transmitter
-
ZZ Resistivity Imaging Pty. Ltd.
*3,000W output power in 2 adjustable voltage ranges ( 400V/7.5A, 1,200V/2.5A), the FlashRES booster transmitter is particular useful for surveys in high resistive areas or IP surveys.*When the FlashRES booster transmitter is connected FlashRES-UNIVERSAL, for each current injection, the system could collect 61 voltage measurement, this greatly increases the data collection speed.*Uses two standard 12V batteries connect in series as input power source*The FlashRES booster transmitter is designed for heavy duty usage, the instrument is shock, water and dust proof.*Light-weight and easily mobilised
-
Product
Miniature Shock Absorbers
-
Miniature shock absorbers from ACE are tried-and-tested quality products used in millions of industrial designs throughout the world. They optimize machines in an equally reliable and effective way by decelerating loads quickly and without recoil.
-
Product
Resolvers
-
Resolvers are electromechanical devices that convert mechanical motion into an electronic signal. Being analog devices, resolvers have no onboard electronics making them ideal for high shock, vibration and other harsh environments. Harowe offers frameless resolvers also known as servo resolvers or pancake resolvers consisting of a rotor assembly that is shaft mounted and a stator assembly that is mounted to the customer's device or housing as well as shafted housed resolvers with flange, servo groves and c-face mounts.
-
Product
Silicon Based Thermopile Detector: 4 Channels
ST120 Quad
-
A four-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Thermal Shock Chamber
-
Allows for the rapid transfer of products between temperature extremes, or the alternating heating and cooling of test articles in cyclical manner.
-
Product
3U PXI-E System Controller
PX32101
-
LinkedHope Intelligent Technologies Co.,Ltd.
PX32101 is a 3U PXI-E system controller based on the newest Intel® Haswell platform. It is designed to provide comprehensive and reliable system controller to support hybrid PXIe-based systems for multiple environments test and measurement applications.Hybrid PXIe-based systems are often required to complete independent diversified complex testing tasks on the PXI test platform. PX32101 provides rich interfaces: 4 USB2.0 / 3.0 for peripheral connectivities; UART for communication or control equipment; dual 1000Base-T Ethernet, one port for LAN connection and the other one for the control of the next generation of LXI instruments. PX32101 can support 4 x4 or two PCIe x8-link, and up to 16GB / s system bandwidth. The ExpressCard 34 expansion slots on the front panel allow users to expand the system modules flexibly. If you install a hybrid multi-slot backplane in the system, then various standard PXI-E and PXI / CPCI peripheral cards could be fitted. In a multitasking environment, PX32101 processor is able to complete multiple tasks independently. The CPU and memory chips soldered with PCB increase reliability performance in shock and vibration environments. Combined with a variety of instrument control interfaces and reliable mechanical & electronic design, PX32101 can meet your hybrid PXIe-based testing for system application requirements perfectly.
-
Product
Vibration Test Systems
-
HIACC Engineering & Services Pvt. Ltd.
Designed to simulate real-world vibration, shock, and environmental stresses for product reliability testing.
-
Product
Connectors
-
Panasonic Automotive & Industrial Systems Europe GmbH
: They have to be as compact as possible and provide maximum reliability. To fulfil these requirements, Panasonic engineers have developed narrow-pitch connectors that utilize TOUGH CONTACT technology.In addition to their excellent shock and vibration resistance, these connectors feature an ultra slim profile, which makes them ideally suited for applications where space is valuable. Our versatile in-device connector product range offers the appropriate solution for practically any scenario.
-
Product
2 Zone Thermal Shock Test Chamber
-
2-Zone Thermal Shock Testing Equipment with programmable electronics.
-
Product
Shock0 to 100g
TGP-0610
-
The shock logger TGP-0610 measures impacts and can be used for machine condition monitoring and the monitoring of expensive and/or fragile shipments.
-
Product
cRIO-9803, Up to 480 GB SSD Expansion Module for CompactRIO
786677-01
Module
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
Product
Shock Absorber Tester
-
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
Product
200 MS/sec RF/IF Rugged Portable Recorder
Talon RTR 2726A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight: just less than 30 pounds- Shock-and-vibration resistant SSDs perform well in vehicles, ships and aircraft- 200 MHz 16-bit A/Ds- 800 MHz 16-bit D/As- 80 MHz record and playback signal bandwidths- Recording & playback of IF signals up to 700 MHz- Real-time sustained recording rates of up to 3.2 GB/sec- Windows® workstation with high-performance Intel® processor- Up to 30.7 TB of SSD storage to NTFS RAID solid state disk arraySystemFlow® GUI with signal viewer analysis tool- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 18-36 VDC power supply
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Shaker Controllers
ZET 017-U Series
-
Shaker Controllers of ZET 017-U series are represented by a software and hardware complex solutions based on FFT spectrum analyzer ZET 017 with task-specific software ZETLAB VIBRO for the control of shock and vibration impact produced by electrodynamic shaker systems. The modular principle of the system structure allows to increase the number of measuring channels from 4 up to 24.
-
Product
Security/Detection
ST60 Dual
-
A two-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant two-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/°C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
PCI Express Mini Card Products (mPCIe)
-
PCI Express Mini Card, commonly abbreviated as mPCIe, or Mini PCIe, is a newer form-factor for PCI Express devices. Designed with the older Mini PCI standard in mind they are the same basic form-factor (commonly used in small-form-factor devices like laptops and other portables) but lack the retention clips of Mini PCI. Unlike the original PCI Express bus, Mini PCIe provides both the standard PCI Express and USB 2.0 signals, allowing flexibility in peripheral design. The standard is highly suitable for industrial automation and test in vehicle, mobile, or any other shock / vibration sensitive application.
-
Product
AGM Marine Connectors
-
Teledyne Marine AG Geophysical Products
Waterproof electrical connectors for high shock extreme applications.
-
Product
6U Compact PCI® Single Board Computer
CP62001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
Product
Converged IoT PXI Chassis
Chassis
The Converged IoT PXI Chassis enables IoT insights and action through three points of convergence in one chassis. It uses sensors to integrate precision data capture and control with security, device, and systems management. Compared to traditional servers, this chassis comes in models that can withstand increased shock, vibration, and broad temperature ranges as well as various mounting options to accommodate compact environments.
-
Product
3.0 GS/sec Ultra Wideband RF/IF Rugged Rackmount Recorder
Talon RTR 2745
-
- Two 3.0 GHz 14-bit A/Ds- Two 2.8 GHz 16-bit D/As- Real-time record/playback rates up to 6.4 GB/sec- Integrated DDCs and DUCs- Capable of capturing RF signal frequencies up to 3 GHz- Captures and reproduces IF bandwidths up to 560 MHz- Captures baseband bandwidths up to 1.5 GHz- 4U 19-inch rugged rackmount PC server chassis- Windows® Professional workstation with high performance Intel® Core™ i7 processor- Designed to operate under conditions of shock and vibration- Removable SSD drives- Up to 61 terabytes of storage in integrated NTFS RAID disk array- Selectable RAID levels of 0, 1, 5, 6, 10 and 50- SystemFlow® GUI with signal viewer analysis tool- C-callable API for integration of recorder into application- Optional GPS time and position stamping
-
Product
Silicon Based Thermopile Detector: 4 Channels
ST150 Quad
-
A four-channel silicon-based thermopile detector in a TO-8 package. Each active area size is 1.5mm x 1.5mm. Affordable four-channel design with strong output and a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Transducer / Transmitter
-
General purpose industrial pressure transducer provides outstanding integrity concerning high shock, vibration and pressure cycling. Utilizing high-performance ASIC, digital compensation provides excellent temperature performance, while the thin film sensor enables long-term stability.
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
