Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
Power Amplifiers
-
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
-
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
-
Product
High Impedance Differential Module
HID
-
Use the HID module in conjunction with a high-speed overcurrent relay to provide three phase high impedance differential protection for substation busbars of any voltage level. Additionally, it can also be used to protect electrical machines like transformers, generators or motors against restricted ground faults.
-
Product
Evaluation Kit for Differential Pressure Sensors of the SDP3x Series
EK-P4
-
The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability.
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Ultra-small / Cable Type]
PM-25
-
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-25 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1mm thereby reducing the possibility of sensing objects colliding.
-
Product
HF Amplifier
Prometheus
-
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Product
High Voltage Op Amplifiers ≥12V
-
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
Product
Wideband Amplifier PXI Card
GX1222
Amplifier
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
Product
1.5 GHz, 1.0 pF Active Differential probe
ZD1500
Differential Probe
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Differential Probe / Paired ProbeTOP
-
*1 Measured at 23°C environment connected to PS-02/PS-03 power supply(optional)*2 Broadband Noise, Bandwidth 30 MHz*3 Referred of output*4 Must be met to achieve best performance and avoid Damage to the Probe*5 Parts#890-880-104 : Twinholder M6 and 890-880-112 : Pair of Rail Clip Connectors 4mm are optional.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
8 Channel Fast Amplifier
V975
-
The Mod. V975 is an 8 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a fixed voltage gain of 10. Channels are bipolar, non-inverting and can be cascaded in order to obtain larger gain values. Input bandwitdth is 250 MHz for signals up to 50 mVpp and decreases for larger ones (up to 110 MHz @ 400 mVpp). Each channel is provided with three LEMO 00 connectors, one for the input and two bridged for the output.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5940-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
RF Power Amplifiers < MMICS
-
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
Product
Low Noise Amplifier
-
Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
Product
Low Noise Amplifier
-
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Dual Channel High Voltage Linear Amplifier
A800D
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Distribution Amplifier
-
Also referred to as a splitter, the distribution amplifier sends one computer, video, or audio signal to multiple devices while maintaining signal integrity.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5946-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Explosion-Proof Differential Pressure Switch
H3
-
Explosion-proof, heavy duty, industrial unit has patented and unique new design which provides sensitivity to differential pressures as low as 10 inches of water (254 mm w.c.), yet handles total pressure of 1500 psi (103 bar). Unlike common differential pressure switches that use a piston-type motion transfer, the Series H3 utilizes a rotary motion transfer shaft that prevents a change in total pressure from causing a setpoint shift.
-
Product
General Purpose Amplifier
-
Easy to use 1.5V to 5.5V amplifiers with 69uA/ch and 150uV offsets, perfect for battery based or power concerned systems.
-
Product
InfiniiMode Active Differential Probe, 3.5 GHz
N2751A
Oscilloscope Probe
The N2751A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2751A probe’s InfiniiMode provides the following modes of operation.
