Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
23 GHz Low Noise Amplifier
HMMC-5023
Amplifier
The HMMC-5023 is a GaAs MMIC low noise amplifier designed for moderate gain and low noise from 21 GHz to over 30 GHz. Typical applications of the HMMC-5023 include digital radio communications systems that operate within the 21.2 GHz to 23.6 GHz and 24.5 GHz to 26.5 GHz frequency bands. Moderate gain and low noise temperature make it ideally suited as a front-end gain stage.
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
Product
RF POWER AMPLIFIERS
BSA Series
-
RF Input:N-f, standard on rear panelRF Output:standard on rear panel<1 kWN-f<3 kW7-16-f<5 kWEIA 1 5/8Mains Supply:Line Power:<1000 VA100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter:via status displayAmbient Temperature:0 ... +45 °CStorage Temperature:-20 ... +85 °CRelative Humidity:up to 95% (non-condensing)Operating Altitude:up to 2000 m above sea levelVibration and Shock:MIL-STD-810 GCooling:forced air with integral blowerair intake from front, air exhaust at rear
-
Product
Solder-In Lead for ZD Differential Probe Qty 2
PACC-ZD002
-
Solder-in lead for ZD differential probeQty 2
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Broadband Amplifiers
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
Product
Power Amplifiers for Radio Amateurs
-
From classic equipment for simple QSOs to high performance modules for contests, EME-operations and satellite radio: Our products provide absolute top performance. When choosing their equipment many radio amateurs and club-stations don't compromise and trust in the proven quality of Kuhne electronic amplifiers. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Our amplifiers are remarkable for high gain and high linearity. LD-MOSFET and GaAs-FET-systems are the state-of-the-art technology in the amateur sector and enable the perfect use for all analog and digital modes (e.g. SSB, CW, WSJT, ATV, DATV). Small mechanical measurements and milled aluminum cases enable high temperature stability and tower mounting. Don't compromise and get technology from Kuhne electronic!
-
-
-
Product
Broadband Amplifier
-
Toellner Electronic Instrumente GmbH
Will reproduce a wide range of signals without significant loss throughout the pass band.
-
Product
Compact Differential Pressure Transmitters
Series 668B/D
-
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
Product
GPS Filter Amplifiers
-
Mercury Systems’ family of GPS filters/amplifiers is the right choice for your high reliability GPS receiver. Whether your application is ground, airborne, missile or launch/reentry vehicle, you can trust the technology behind these advanced products. Custom designs including multiple outputs and integrated receiver protection limiters are also available.
-
Product
Variable Gain High Speed Linear Amplifier
F30PV
-
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
-
Product
System Amplifiers
N4985A
Amplifier
The Keysight Technologies N4985A series system amplifiers are high performance broadband amplifiers with excellent power and gain from 100 kHz to 50 GHz. The amplifiers are self-contained and plug into standard AC power sources.
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Medical Masks Differential Pressure Tester
-
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
Product
Single and Multi-Function High Power Amplifiers
-
This lab unit is capable of a power output of 30 Watts and operates at a frequency range from 1200 MHz to 1400 MHz. The compact and rugged design of this system is ideal for bench-top testing and many other applications where both simplicity and portability are required.
-
Product
Differential And I/Q Device Measurements
S97089B
-
The S97089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
RF Amplifiers up to 2500 MHz
-
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Ytterbium-doped Fiber Amplifier
YDFA
-
Ytterbium-doped Fiber Amplifier (YDFA) is another Amonics specialised product line. Like our highly recognized optical amplifiers, the YDFA offers high output power and high gain with exceptional reliability. ideal for high power YDFA applications. The turnkey microprocessor controlled benchtop YDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition. Available options include single frequency operation, linearly polarized operation.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
Saluki SE2031 DSP Lock-In Amplifier
-
SE2031 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 10 MHz. With the advantage of the latest digital signal processing technology and high-speed 16-bit ADC, SE2031 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE2031 is as good as other lock-in amplifier brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE2031 integrates some special functions like multiple harmonic measurement, which meets the needs of scientific research and industrial application well.
-
Product
Broadband RF/Microwave Power Amplifier
-
R&K wideband power amplifiers support a wide range of applications with their broadband characteristic.
-
Product
1.5 GHz, 1.0 pF Active Differential probe
ZD1500
-
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
Saluki SE1022D DSP Lock-In Amplifier (Dual-channel)
-
SE1022D Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. More importantly, SE1022D has dual independent input channels and dual independent high precision signal generators. Each input channel and signal generator can be used independently which means that the SE1022D is equivalent to two traditional lock-in amplifiers. Moreover, due to the twin symmetrical design, the two independent input channels and signal generators have ultra-high synchronicity, which meets the measurement requirements demanding extremely high synchronization.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Composite 2×12 Video Distribution Amplifier
VDA212RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
