Phase Angle
Measure electrical phase angles or visualize stero sound.
See Also: Phase, Phasing, Phase Standards, Phase Meters, 3 Phase, Phase Angle Meters, Phase Angle Voltmeters, Phasors
-
Product
LISNs - Three Phase
-
Com-Power three-phase LISNs in three series — LI-3P-1X (CISPR/ANSI, 150 kHz–30 MHz), LI-3P-2X (CISPR/ANSI V-AMN, 9 kHz–30 MHz), and LI-3P-4X (MIL-STD-461, 10 kHz–10 MHz) — covering 16 A to 100 A per phase for conducted emissions testing of industrial, commercial, and military three-phase equipment in Delta and Wye configurations.
-
Product
Phase Detector
Paula
-
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
Product
Spectral Phase Measurement
Avoca SPIDER System
-
Spectral phase interferometry for direct electric-field reconstruction (SPIDER) is one technique that can recover the spectral phase of an input pulse, without needing any reference pulse. SPIDER interferes two pulses which areseparated in time and in frequency, and the resultantinterferogram is read by a spectrometer.
-
Product
30" Support Angles
SA-30
-
30" support angles provide 3” of horizontal surface along each side of vertical cabinet for supporting instruments.
-
Product
Phase Stable Cables
FlatPhase 100 Series
-
Best in class phase stability vs. temperature makes FlatPhase™ the preferred option when you need flat phase.Our proprietary foamed fluoropolymer dielectric avoids the typical PTFE knee to deliver a flatter phase response.
-
Product
Synchro or Resolver Angle Indicator Readout
AITM
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed multiturn synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used.
-
Product
Phase Behavior
-
PVT Systems are used to perform PVT studies on a variety of fluids with a special emphasis on those fluids typically encountered in petroleum reservoirs. Our PVT systems are mercury-free and easy to use.
-
Product
Phase Rotation Tester with Voltmeter
885 PR
-
Standard Electric Works Co., Ltd
● 3 functions in one unit: Phase Rotation, Phase Presence, Voltmeter● LCD contact type Phase Rotation Tester● Large LCD to show phase rotation and phase presence● Check a wide range of three phase power sources● Voltage range for phase rotation test: 75~600V AC ● Frequency range: 40~400Hz● 6000-count voltmeter● Auto ranging Voltmeter AC/DC● Data hold function● Auto power off● Convenient stand for viewing● Easy to use● Comply with EN 61010-1 CAT III 600V EN 61010-2-033 EN 61326-1
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS HL
-
Optik Elektronik Gerätetechnik GmbH
Measuring instrument for contact angle and surface free energy, special solution for semiconductor technology for wafers up to 300 mm.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
Multiple Angle Laser Ellipsometer
PH-LE
-
The multiple angle laser ellipsometer provides film thickness, refractive index and absorption index at the HeNe laser wavelength 632,8 nm with an extraordinary precision and accuracy. It can be utilized to characterize single films, multiple layer stacks and bulk materials.
-
Product
Phase Meter
SD1000
-
The SD1000 phase meter offers superb accuracy with a wide range of signal conditions. Conventional phase meters are easily upset when small levels of noise and distortion are present - the result is often unstable and incorrect phase readings. The SD1000 overcomes this by using Discrete Fourier Analysis (DFT), this process rejects any noise and distortion without the need for tracking filters.
-
Product
Source Phase Control
S93088B
-
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
Product
HOT STICKS & PHASING STICKS
HS-15
-
Hot Sticks and Phasing Sticks are voltmeters designed so to permit testing of high-voltage lines or bus bars. The meter is conveniently located, and tilted downwards for easy reading to 5% of full scale.
-
Product
9-36kV Phasing Voltmeter
-
STB Electrical Test Equipment, Inc
Provides safe and convenient testing means for paralleling 3-phase high voltage circuitsConsists of two resistance elements connected in series with an indicating meter in the series connectionTwo ranges, 9kV and 36kV, with a range selector switch mounted on the back of the meter housingSwitch is clearly marked for the range of the voltmeterTypical use: Line-to-ground voltage measurements and phase for paralelling operationsScale markings on the voltmeter have a minimum of divisions and the figures are large enough to be easily read 8′-10′ away when mounted on a suitable hot stickInput impedance: Approximately 72 megohmsMaximum operating temperature range -20°F to 165°F (-30°C to 75°C)Ready to attach on hot stick10′ cable, a proof tester, battery and shepherd’s hook and probe tip included
-
Product
Right Angle Poppet Valve
PV10
-
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
Product
Phase Stable Cable Assemblies
Phase Master
-
Superior phase stability vs. temperature makes this cable the ideal choice for phase-sensitive applications— particularly those with wide operating temperature ranges.Phase Master's enhanced phase stability— a result of a proprietary combination of high performance, tape wrapped PTFE dielectric and helically wrapped SPC shield—offers:- Improved system performance- Less frequent calibration- More precise measurementsFrom environmental stress screening to electronically scanned radar systems, count on Phase Master® assemblies to provide unparalleled value and performance.
-
Product
902s Six Phase 30A
-
Weshine Electric Manufacturing Co., Ltd
Single-phase current output (RMS)0--30A/phase, accuracy: 0.2% ±5mASix-phase parallel output (RMS)0--180A/six-phase parallel outputPhase current allowable working value for a long time (effective value)10AMaximum output power per phase320VASix-phase parallel current maximum output power
-
Product
Three Phase Protector
KPB1
-
Konstar Electric Industrial Co., Ltd
If have one pase voltage is too high or two low or pahse lose or wrong phase sequence, the protector will cut off the power, and the new power supply, it will have 5s-300s to restart the equipment in order to protect them.Suitable for the engineer, and equipment and three phase equipment.
-
Product
Low Voltage Single Phase
600V Class
-
These transformers are encased in a thermoplastic case with the core and windings encapsulated in resin. They are designed for line-to-line operation but may also be used in line-to-neutral or line-to-ground configuration at 58% of rated voltage. It is recommended that a 1.6 Amp fuse be used in the secondary to protect the transformer.
-
Product
Phase Noise Measurement Solutions
-
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
Product
Meters For Contact Angle And Surface Tension
Contact Angle Standard
-
Optik Elektronik Gerätetechnik GmbH
The contact angle standard is a glass plate with images, representing sessile drops with different contact angles. The contact angle standard is manufactured by a high accurate lithographic process, so the images itself are very accurate according the given CAD-data. The Glass plate is placed on the measuring table instead of a real drop. The proof of the reproducibility of the contact angle measurement is performed by a repeated measurement of the object (sessile drop). For a correct test, the measurement must be performed, using the live video (not a frozen image). For a real sessile drop exists the problem, that it evaporates permanently. The result of the permanent evaporation is the permanent change of the contact angle. Therefore, the proof of the reproducibility of the contact angle measurement is not possible, using a real liquid, since the object changes permanently the contact angle!
-
Product
Wide Angle Scale Instrument
LS-80
-
Standard Electric Works Co., Ltd
● Easy to read long-scales and pointer-indications can easily be read from a distance.● Full Scale Deflection：250°● Accuracy： Class 1.5● Scale Length ：140 mm● Case and Composition： Polycarbonate window, plastic body and terminal, Four studs mounting.● Color：White scale plate, black terminal plate, black meter body.● Pointer：Sword-type in black color.
-
Product
General Purpose Benchtop XRD System for Phase I.D. and Phase Quantification
-
In a move to bring lab-quality performance to the manufacturing floor, Rigaku introduces the MiniFlex XpC, a manufacturing-optimized powder diffractometer for fast and accurate quality control measurements. It is extremely easy to operate using Rigaku’s new EasyX quality control software, which requires minimal clicks to run. A minimal interface means there will be no accidental error variance from operator to operator. The MiniFlex XpC can be configured with a conveyor belt or robot for automated sample processing and collaboration with other instruments. With an 800 W X-ray source and a short-diameter goniometer, the system has the performance of a lab unit, and thus can greatly improve throughput for quality control measurements.
-
Product
Phase And Continuity Tester
4100A
-
Peaceful Thriving Enterprise Co Ltd
There are two function of this tester. One is to test the continuity and the other one is to test the phase of three-phase system. The operation is easy, the indication is clear with LED indication. There is a loud buzzer to remind you the continuity. The illumination is very helpful in the dark environment.
-
Product
3 Phase Meter - Clockwise
135007
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
Three Phase Tester
4200
-
Peaceful Thriving Enterprise Co Ltd
*Fast and accurate measurement.*Portable and compact design, easy to carry.*Efficient, effective, reliable, easy and safe to use.*Two function in one unit. Including open phase and phase sequence.*This is idea for installing conveyor lines, pump systems and interconnected drivers.*Indicate phase orientation (clockwise or counter-clockwise) and whether each of three phases is live.
-
Product
26-Pin D-Type Female Right Angled PCB
40-963-026-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Knopp Phase Sequence Indicator
K-3, K-6, and K-7
-
Use of the Knopp K-3 Phase Sequence Indicator saves man-hours and protects valuable equipment against damage. It pays for itself in a short time. Specially designed induction motor unmistakably indicates the phase sequence by direction of rotation or rotor disc.
