Comparators
Contrast similar or divergent values.
-
Product
Rad-Hard Analog ICs
-
ST's wide range of rad-hard QML-V qualified analog ICs covers analog-to-digital converters (ADC) and digital-to-analog converters (DAC) for telemetry, instrumentation and imaging applications. Our portfolio also includes rad-hard op amps, high-speed differential amplifiers up to 1 GHz, shunt voltage references and comparators to ensure a complete solution for signal conditioning, referencing and data conversion.
-
Product
Laser Photometer
8587A
-
The photometer owners asked TSI to develop a modern version of the Laser Photometer 8587 that retains data continuity with the original version. Without data continuity, vast amounts of legacy research would not be directly comparable to new research. The result was the Laser Photometer 8587A.
-
Product
Fluxmeter
B3
-
Electronic integrator of high sensitivity and extremely low drift. Equipped with RS 232 interface, maximum minimum store and comparator. 4 measurement ranges. Constants of measuring ranging from 10E-7 Vs/digit to 10E-4 Vs/digit.
-
Product
Computer Based Audio Component Test System
DATS V3
-
Rugged aluminum housing with detachable test leads and built-in precision calibration resistorTighter tolerances on internal components for more precise measurementsIncreased output capability means greater separation from the noise floor, resulting in more accurate measurementsDATS Linearity Test for comparing parameters and impedance plots at multiple drive levelsOptional under desk mounting brackets included to save desk spaceOnly 1" H x 2-1/2" W x 4-1/8" D for easy portability
-
Product
SDIO Wi-Fi Module
SX-SDMAC
-
This Wi-Fi SDIO module is a low-power, single-stream solution with 802.11a/b/g/n/ac support based on the QCA9377 System-on-Chip from Qualcomm Atheros. This module supports Wave 2 MU-MIMO (Client), which increases the overall WLAN system performance by 3X compared to 11n. The module’s small form factor, rich features, and low power make it perfect for portable devices.
-
Product
Measurement/Analysis Software O-Solution
DS-5000
-
•Compare/ analyze the data with wide sampling frequency from 10 μHz to 100 GHz•Flexibly layout to compare the data in different formats or sampling frequency•Support various file formats including other company's loggers•Perform multiple data analysis (up to 1,000) simultaneously•Further analysis on specified area with the marker function
-
Product
IC Testing System
-
Is a system for giving electrical signals to a semiconductor device to compare output signals against expected values for the purpose of testing if the device works as specified in its design specifications.
-
Product
Multi-Channel Phase Comparator
VCH-315M
-
Multi-channel phase comparator VCH-315M, together with a computer and special software, is designed for simultaneous measurement of frequency instability characteristics (RMS, RMS) of a group of sinusoidal signals of standard frequencies 5; ten; 100 MHz.
-
Product
One-Shot Image Checker
Focus-6500IA (TASCAL)
-
This is the image checker which inspects boards by comparing pre-registered reference image with captured image of inspected board.(Pattern Matching processing)
-
Product
Arbitrary Function Generator PXI Card
GX1200/GX1201
Waveform Generator
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
Terrameter LS 2
ABEM
-
Now Guideline Geo is introducing a new unique IP feature using 100 % duty cycle. This means twice as fast data collection and double the signal to noise ratio compared to the conventional IP method (50%) using the same settings.Resistivity/IP surveying is a versatile geophysical method suitable for a broad range of applications and environments such as groundwater prospecting, mineral exploration, geological mapping and geotechnical investigations. Depending on the application used, system designs can vary. ABEM Terrameter LS 2 has been made available in many different configurations to perfectly match your requirements.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
ServoBelt™ Rotary Stage
-
ServoBelt™ Rotary is a series of compact, high-torque motorized rotary stages that offer through hole size and speed comparable to direct-drive rotary tables costing thousands more.
-
Product
Automated Streetlight And Sub-meter Testing
Multi-channel Pulse Comparator
-
Sub-meters and streetlight meters are becoming major topics of interest in the electric utility industry. As these new meter types approach revenue grade, utilities are looking for an effective way to test them in high volume, while maintaining the NIST traceability required if they are to be used for billing. To maximize meter shop efficiency, utilities need a way to test these meters using their current testing processes. The RADIAN Multi-Channel Pulse Comparator is here to solve this challenge.
-
Product
Dynamic Signal Acquisition and Analysis
-
m+p Analyzer systems are available for field and laboratory use from 4 to many hundreds of measurement channels. From gathering simple time history data to narrowband (FFT) spectra, fractional octaves, wavelets, shock response spectra and much more, m+p Analyzer real time analyzers can be used with a wide range of instrumentation hardware including our own m+p VibPilot, m+p VibRunner and m+p VibMobile systems, National Instruments (CompactDAQ USB, PCI, PXI) and VTI Instruments (PCI). Low cost portable instruments to systems for distributed measurements can be configured for maximum flexibility. Measurement data from all sources are stored in a common format so it is easy to compare and handle results from any measurement source.
-
Product
Inline Module Band
-
Computer Gesteuerte Systeme GmbH
The transport belt runs over a spring-loaded belt-clamping unit and is made of ESD material. The clamping unit ensures that the belt is tensed properly and is automatically readjusted, resulting in a longer life when compared to conventional conveyor systems.
-
Product
Partial Discharge Expert Diagnostic and Location System
PDExpert
-
Power Monitoring and Diagnostic Technology Ltd.
The PDExpert is PMDT's third level of Partial Discharge (PD) Expert Diagnostic and Location System. It is a powerful, portable, multi-channel system of impeccable design used to analyze and pinpoint PD signals coming from a power asset within centimeters while the power system is energized. The system consists of UHF, AE, HFCT and ultrasonic sensors, one advanced UHF/PD signal processing unit, one oscilloscope, filters and other accessories.The system employs ultra-high speed data acquisition and advanced digital signal processing technologies, compares the UHF, AE and HFCT signals of different frequency ranges to determine if it is PD or noise, and locates the source in power assets accurately by utilizing Acoustic-Electromagnetic Combination Location Technique, time Difference of Signals' Arrivals (TDOA), and 3D Positioning Technology.
-
Product
Fiber Identifiers
-
This equipment is rugged and easy-to-use making it simple for a technician to identify live fiber which ensures that the fibers are connected. This tool also identifies the frequency and the traffic direction. It saves time and money when compared to other pieces of more elaborate test equipment. Most importantly, this device performs this task without any harm to the fiber optic cable. Because the technician is only clamping the device on the fiber the identifier does not disrupt signal traffic.
-
Product
Pitot Tubes
-
The dpm-i Pitot Tube is a new design concept in Pitot Static Tube technology. It is a multi-functional sensor. It can replace thermally heated instruments, where power requirements are high. Gives easy access to duct measurement compared to a standard Pitot Tube. For example, in ceilings voids and confined areas, where there is a thick lagging or metal cladding.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Test Kits
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifier (includes MASTER and REMOTE devices) Tests two fibers at a time, cutting testing time in half (when compared to traditional fiber certification) Ideal for installers and contractors who need to certify fiber cables BI-DIRECTIONALLY Measure the end-to-end length of the fiber cable with every test Unlimited sets of job parametersOWLView software allows tri-report capability certification, OTDR, and endface all on one report) Multimode and singlemode options available.
-
Product
Display
Multichannel Oscilloscope
-
Multichannel Oscilloscope is used for evaluating signal shape and instant value measurement. It is possible to simultaneously display several signals within the same period, each having their own units of measurement. To compare signals, it is possible to display their oscillograms on the same coordinate axes. A simple and user-friendly cursor control and diagram scaling allow for studying process changes in general and in detail.
-
Product
Digital Insulation Tester
SK-3502
-
125V/250V/500V/1000V, Comparator Function., Data Memory (up to 100 data)., Low Resistance Measurement., AC/DC Voltage Measurement., Enhanced Safety Functions.
-
Product
Photolysis Rate Analyzer
PFS-100
-
, HONO, HCHO etc.) are key indicators for identify status & extent of photochemical pollution.The analyzer is receiving solar radiation by quartz probe and transferring the radiation to spectrum via optical quartz fiber, the spectrum data will be evaluated and compared with reference data with mathematical approach and gives photolytic rate.
-
Product
Crawler Control Unit
CCU186
-
The CCU186 control unit for crawlers possesses a distinct advantage compared to existing products. In fact, all of the performances that are usually achieved with standard control units are now available in the crawler configuration. Automatic slow preheating, the progressive rise in voltage with each exposure, as well as a selection of set values are all included in the CCU186.As the CCU186 has been entirely fitted with industrial electronic components, it is perfectly suited to the often extreme conditions of automatic intra-tube control campaigns.
-
Product
TeleScan PE Software
-
The powerful display allows users to group the devices in a simple device tree, Device/Port/Type, or Bus/Device/Function numbers. All register field descriptions are displayed by selecting the individual fields. Each register value in a single PCIe component's register can be read and if writable can be modified. The user can decode and change each bit value of any register on the fly using the built-in the PCIe specification display referenced for all registers. The extended register for M-PCIe is also decoded and displayed for devices supporting that specification. The PCIe/NVMe configuration space info on one system can be saved and later compared to a different system by loading a saved configuration onto a second system. Searching is available for locating PCIe devices. Other features include Auto Scan, Configuration Space View, Specification decoding for standard registers. The utility supports scanning on host machines using Microsoft Windows 7, 8, 10 and on Linux systems.
-
Product
PCIe 16 Bit Multi-Purpose Digitizer - up to 80 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5943-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Calibration Management Software
MET/CAL®
-
MET/CAL software is structured around the flow of instruments through the calibration process and addresses a wide range of test and measurement instrument calibration needs, from the simple to the complex. It is based on the traditional calibration model as its framework—comparing an instrument to a standard of known uncertainty.
