T1
A phone line connection with data rates of 1.544Mbits per second over 24 channels running at 64Kbs.
See Also: E1
-
Product
ISDN Chip Set
Emutel Symphony
-
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
Product
1000BASE-T1 MEDIACONVERTER EMC
Art.-Nr.: TE-1404-1
-
The ideal solution for working quickly and efficiently with 1000BASE-T1 EMC measurements The 1000BASE-T1 MediaConverter EMC is especially designed for measurements within the EMC chamber. It is delivered in a Set with an adapter board which enables internal PHY status readings and provides one point-to-point connection between Automotive Gigabit Ethernet and SFP Gigabit Ethernet, with which optical fibre modules are used.
-
Product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
-
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
-
Product
1000BASE-T1 Ethernet Logging Expansion With Low Latency
PT-20MG
-
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
Product
2 Port T1/E1/PRI + 8 Port FXS PSTN
CH-8FXS-MOD-2PRI
-
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
100BASE-T1 SFP Module
Art.-Nr.: TE-1430
-
Convert between 100BASE-T1 and Standard Ethernet The 100BASE-T1 SFP Module is the optimum solution to convert between 100BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 100 Mbit/s full-duplex 100BASE-T1.
-
Product
2 Port T1/E1/PRI + 8 port BRI-U ISDN
CH-8BRI-U-MOD-2PRI
-
This unit has two PRI ports and 8 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
8 Port T1/E1/PRI Bulk Call Generator
BCG-8PRI
-
This unit has eight PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test. It can be used to generate call volume to VoIP geteways, PBXs, Fax servers, RAS serves.
-
Product
8 Port T1/E1/PRI ISDN Simulator
SIM-8PRI
-
The most inexpensive ISDN simulator on the market. This unit has eight PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
WAN Tester II
-
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
Product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
-
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
Product
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
-
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface. The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 1000 Mbit/s full-duplex.
-
Product
100BASE-T1 MEDIACONVERTER BCM
Art.-Nr.: TE-1000
-
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter BCM establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
1000 BASE-T1 Ethernet
1000 BASE-T1 Ethernet
Compact, powerful computers and servers support diverse smart city applications at edge points.
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Multifunction Electrical Installations Meter
MPI-525
-
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
WAN Tester lllD
-
It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems, multiplexers, CSU/DSUs, T-1 CSUs, DDS CSUs, DDS CSU/DSUs, DTUs, NTUs and TIUs. The Ds3 tester is supplied with user-changeable nickel metal hydride batteries and a built-in charger.
-
Product
100base-T1 Ethernet (BroadR-Reach®) Logging Expansion With Low Latency
PT-15B
-
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
Product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire H-MTD Cable Jack, 1 Position
7-142716765-036
VTAC Patchcord
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Position.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
New Generation Analyzer For IEEE C37.94
NetProbe 2000 C37.94
-
The NetProbe 2000 C37.94 is a field analyzer with IEEE C.37-94 Multimode optical fiber interface for testing bit error preformance between teleprotection and digitalMultiplexer equipment. Can be combined with many optional interfaces for T1,E1, WiFi, VoIP and V-series testing.
-
Product
4 Port T1/E1/PRI Bulk Call Generator
BCG-4PRI
-
This unit has four PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test. It can be used to generate call volume to VoIP geteways, PBXs, Fax servers, RAS serves.
-
Product
On-line TOC Analyzer
T1 - TOCADERO Series
-
- Highest analytical precision with short measuring time- Catalyst-free high-temperature process at 1200°C with "Fast Change Technology- Most modern hardware components andindustry 4.0 features- Minimal material requirements and support costs- Highest processing quality- "Made in Germany"- Global service and support- Convincing cost of ownership
-
Product
HD Thermal Camera
T1010
-
The T1010 uses the power of FLIR Vision Processing™ to deliver detailed, smooth pictures with very little image noise. FLIR Vision Processing combines HD resolution, MSX®, and UltraMax® image enhancement with FLIR's proprietary adaptive filtering algorithms to produce brilliant thermal images with up to 3.1 million pixels. Plus, the T1010 is sensitive enough to detect temperature differences down to <20 mK, for clear, low-noise results that keep you from missing any potential issues during inspections. 1024 × 768 true HD resolution images, with thermal measurements up to 650°C (1202°F).
