Isolation Amplifiers
-
Product
CATV Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
Product
LT Range Broadband Power Amplifiers 20 MHZ - 1000 MHZ
LT Series
-
Class A solid stateBroadband (instantaneous single band): 20 MHz 1000 MHzTypical output power : 90 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 60 W and H < -20 dBc from 20 MHz to 80 MHz andP1dB > 75 W and H < -20 dBc from 80 MHz to 500 MHz andP1dB > 45 W and H < -20 dBc from 500 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to LT 160 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
2-Ch Sensor Amplifier
SR-2210
-
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
Product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
-
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
Product
Charge Amplifier
-
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
Power Amplifier
DPA8-0.4-22G-2032
-
Power Amplifier, Frequency 0.4~22GHz, Gain 40dB, Psat 30dBm, SMA Female
-
Product
2 Channel Microphone Power Supply and Conditioning Amplifier
SoundConnect 2 mic power supply
-
SoundConnect 2 is a rugged 2-channel USB controlled microphone power supply and conditioning amplifier.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Microwave Power Amplifier 1/2 Watt 100 MHz to 20 GHz
GT-1020A
-
The Spanawave/Giga-tronics GT-1020A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
Shortwave Power Amplifier
OM4001A
-
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
Low Noise Amplifier
-
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Isolated Process Control Signal Conditioning Products
SCIM7B
-
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
-
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
Product
PHIL 4-Quadrant Power Amplifier
PAV5000
-
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Analog Isolator
-
The Analog Optical Isolator module is a single isolated current in / current out or voltage in / voltage out channel of physical separation and electrical isolation for establishing and maintaining the independence of Class 1E equipment from non -Class 1E instrumentation circuits. Input-to-Output isolation has a steady-state isolation capability of 2500 volts AC rms. This isolation will be maintained between:a) input to output signalsb) input to output powerc) output signal to input power
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
DT Range Broadband Power Amplifiers 10 KHZ - 1000 MHZ
DT Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 1000 MHzTypical output power : 25 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 20 W and H<-20 dBc up to 450 MHz andP1dB > 10 W and H<-20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Non-Linear Pulse Amplifiers
-
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
-
Product
Five Channel Amplifier
-
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
Product
Amplifier Gain Blocks
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a wide portfolio of Amplifier Gain Blocks for RF, microwave, and millimeter wave applications. Our amplifier gain blocks cover frequencies ranging from DC to 45 GHz. MACOM’s gain blocks are used in a variety of 50 Ohm and 75 Ohm applications including; Networks, Commercial and Aerospace and Defense. Leveraging the latest innovative technology these products are available in both standard plastic packaging and bare die.
-
-
Product
Linear High Efficiency Power Amplifier
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's high efficiency linear power amplifiers are available for operating frequencies from 1MHz to1 GHz with output power from 1 to 100 watts. Combined with linear design, these linear power amplifiers provide ultra low distortion, suitable for multi-band, multi-mode communication applications. With built-in monitor circuits, Keylink's power amplifier assure consistent performance in terms of reliability. KeyLink's linear power amplifiers can be categorized as follows:
