Comb Generators
a reference signal source outputing multiple harmonics of the input signal.
See Also: Open Area Test Sites
-
Product
Comb Generators
-
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
-
Product
Comb Generators
-
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
Product
Comb Generator
WJ10-100A
-
Comb Generator model WJ10-100A with Broadband Antenna. Frequency Range 10MHz - 11 GHz with two frequencies step size option; 10/100 MHz
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Dual Channel Synthesizer
SYNTH1400X2
-
Convenient Ethernet ApplianceControllable from anywhere by computer or mobile device100KHz to 1400MHz frequency tuning in 190 picoHertz stepsTwo synthesizers are independently programmableBoth synthesizers track due to common reference16-bit phase tuning resolution12-bit amplitude scalingProgrammable modulusAutomatic linear and nonlinear frequency sweeping capabilitySwitchable frequency/phase-offset profilesUltra-low phase noiseOptional pulse comb generator output
-
Product
Low Phase Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
Product
Comb Generators
-
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
Product
Comb Generator
WJ10-25A
-
Comb Generator model WJ10-25A with Broadband Antenna. Frequency Range 10 MHz - 8 GHz, with two frequencies step size option; 10/25 MHz
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Microwave Comb Generator
-
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
Comb Generator, 10 MHz To 110 GHz
U9391M
-
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Comb Generator, 10 MHz to 67 GHz
U9391G
-
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Radiating Comb Generators
TBCG1
-
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
Product
Comb Generator, 10 MHz to 50 GHz
U9391F
-
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
-
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
Product
Comb Generator
WJ10-50A
-
Comb Generator model WJ10-50A with Broadband Antenna. Frequency Range 10 MHz - 11.0 GHz with two frequencies step option; 10/50 MHz
-
Product
Vector And Scalar Mixer / Converter Measurements
S95083B
-
The Keysight S95083B measurement software includes the scalar mixer / converter plus phase (SMC+Phase) measurement class. It provides fully calibrated conversion gain / loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C / F / G comb generator and an external DC power supply. A vector mixer characterization (VMC) is also included for measuring group delay of frequency-converting devices. VMC can be used to characterize a user-supplied calibration mixer.
-
Product
PXIe-5423, 40 MHz Bandwidth, 1-Channel, 16-Bit PXI Waveform Generator
785115-01
-
The PXIe-5423 is a 40 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms and standard functions including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -12 V to +12 V and uses a fractional resampling method to precisely generate waveforms. The PXIe-5423 also features advanced synchronization and generation features like waveform scripting and streaming.
-
Product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-03
-
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
Product
18 Bit / 300 MS/s Arbitrary Waveform Generator
AWG18
-
The AWG18 is an 18 bit Arbitrary Waveform Generator for high-speed / high resolution waveform generation. This module features two dedicated signal paths. A DC to 100 MHz path which is optimized for accurate time domain and frequency domain measurements up to 30 MHz. And a dedicated AC path optimized for signals between 10 MHz to 100 MHz. In combination with the built-in filters it features a typical harmonics level of better than -80 dBc for the whole range.
-
Product
Waveform Generator, 20 MHz, 2 Channel
EDU33212A
-
The EDU33212A dual channel function / arbitrary waveform generator provides uncompromising performance for dual channel synchronized test output signals.
-
Product
12GHz Dual Channel Signal Generator 19" 1U Rack Module
LS1292R
-
The LS1292R, 12GHz Dual Channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. The LS1292R features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1292R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
6GHz Dual Channel Signal Generator 19" 1U Rack Module
LS6082R
-
The LS6082R, 6GHz dual channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” space efficient, rack-mounted box. The LS6082R features two phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6082R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
Arbitrary Function Generator 14-bit, 100Msa/s
PXI-5412
-
The PXI-5412 is a 20MHz arbitrary waveform generator for generating custom arbitrary waveforms and other standard functions such as sine, square, triangle, and ramp. The arbitrary generator generates signals from -6 V to +6 V and uses direct digital synthesis (DDS) to generate precise waveforms.
-
Product
6GHz RF Analog Signal Generator Module
LS6081D
-
The LS6081D, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS6081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081D was designed to offer industry leading price to performance ratio, needed from the R&D benches to the production lines.
-
Product
3-Channel PXI Function Generator
41-620A-003
-
The 41-620A is a compact 3-channel function generator provided in a PXI 3U single-slot module and is fully backward compatible with our 41-620-003 module. It is capable of generating sine waves to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. This module can generate arbitrary waveforms loaded into the internal 256k memory, allowing the function generator to emulate many waveform types, including the typical waveforms of automotive and aerospace sensors.
