Multifunction Meters
-
Product
Multifunction Module for 34970A/34972A
34907A
Digital I/O Module
The Keysight 34907A module for the 34970A/34972A Data Acquisition/Switch Unit allows great flexibility for a variety of sense and control applications. It combines two 8-bit ports of digital input and output, a 100 kHz gated totalizer, and two 12V analog outputs - all on a single earth-referenced module. The digital inputs and totalizer input may be included in a scan. Alarm limits for the digital and event counter inputs are evaluated continuously, capturing and logging alarm conditions even between scans.
-
Product
Multifunctional Cable Detectors
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Multifunctional Cable Detector has a very high cost-effective, it can quickly trace and identify UTP/STP RJ45/ RJ11/BNC/ metal cable.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
Multifunction Cable
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
Multi-Functional Dynamic System Monitor
PFMonitor
-
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
Product
Multifunction Process Tools
-
Fluke Multifunction Calibration Tools are designed to calibrate almost anything. These calibration tools source and measure almost all process parameters, and documenting versions even document the results The Fluke 754 does the work of several tools - sourcing, simulating and measuring pressure, temperature, and electrical signals in one compact, hand-held device. The Fluke 726, specifically designed for process industries, measures and sources almost all process parameters and can calibrate almost anything in the plant.
-
Product
Shock/Bump Multifunctional Tester
DP-201
-
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
Product
Cable, 10 Pos Combicon to Pigtail, 1 Meter
190656-01
Multifunction Cable
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
Product
Multifunctional Power Supply
M66 series
-
M66 series DC power supply, as a new generation product of programmable power supply with widely range of application, can meet a variety of occasions of measurement requirements. It not only supports all characteristics of high-accuracy power supply, but also can be used in testing cellular phone, DC machine servo driver, any external wave amplification driver, precision electronic components feature,and so on. Supproting be programmed through the keyboard on the panel which will bring great convenience to the users.Moreover, M66 series programmable multifunctional power supply is your best weapon for cellphone research, micro-electronics lab,research institue .
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
Multi-Function I/O FPGA PXI Card
GX3722
Multifunction I/O
The GX3722 is a user configurable, FPGA-based, 3U PXI card which employs a multi-function, analog / digital, I/O daughter board. The module offers multiple analog and digital source / measure capability. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Product
Multifunctional Thermal Imaging Monocular
FLIR Breach® PTQ136
-
Built for the rigors of law enforcement, the FLIR Breach PTQ136 spots the heat of suspects and objects in total darkness. Featuring the new FLIR Boson core and a compact design, the FLIR Breach offers unmatched tactical awareness. Weighing only 7.4 ounces (210 grams), the FLIR Breach can be concealed in a pocket or mounted to a helmet with its mini-rail feature, while adding minimal weight to officers’ heavy gear. Additional features include onboard recording and seven palettes for fast detection of suspects or evidence, day or night.
-
Product
3U OpenVPX Multifunction I/O Board
68C3
Multifunction I/O
NAI’s 68C3 is a 3U OpenVPX multifunction I/O and communication board with three function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Programmable Multifunction Generator
IST 5800/5850
-
IST Information Scan Technology, Inc.
The IST-5800 series programmable multifunction generator is an exceptionally versatile and economical instrument for applications in R&D, Manufacturing Test, Service Repair and Training. Featuring an adjustable triple output power supply and waveform generator, it has the ability to provide power and signal sources for a circuit while the universal logic probe, auto-ranging frequency counter, and digital voltmeter allows you to simultaneously analyze and measure circuit activity.
-
-
Product
MULTI-FUNCTION AVIONICS TEST SET
TR-220
-
Tel-Instrument Electronics Corp.
The TR-220 provides test capability for Traffic and Collision Avoidance Systems (TCAS), Distance Measuring Equipment (DME) and Transponders (Modes A, C, and S). The TR-220 features state-of-the art design technology. Microprocessor control results in easy-to-use operation that requires minimum amounts of training. Setup menu allows storage of various test parameters to facilitate quick recall of test conditions.
-
-
Product
Multifunction Power & Harmonics Analyzer
KM 2100 / KM 2200
-
Kusam Electrical Industries Limited
Volts / Amps. / Hertz, Dips & Swell, Power / Energy. Unbalance, Monitor, Scope, Harmonic, Logger &, Interruption functions. (KM 2200). Inter Harmonics, Transient Voltage, Inrush Current, Flicker function not available in KM 2200. Frequency upto 400Hz (KM 2100); 50 / 60Hz (KM 2200). Single-phase 2W / Single-phase 3W / 3-phase 3W / 3-phase 4W. Flash memory 128MB. TF Card 8G Memory Card for long-term measuring data storage. Support USB port to connect to PC and analyze the data / screen shots copied by U-disk. Support LAN port to make the remote control available, transfer the measuring data.
-
Product
Multifunction Installation Tester
COMBIG2
-
Multifunction installation tester with colour touchscreen display and WiFi compatible with HTANALYSIS™
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Milliohm Meters & Microhm Meters
-
Shanghai Beha Electronics Co., Ltd.
Makes measurements by passing a constant current through the device under test (generally a conductor, contact or low resistance) and measuring the voltage across it. It has visual LED checks for excessive; potential lead resistance (RP) and current lead resistance (RC). Should the instrument become too warm, the temperature sensor will shut down the current (ISCOFF).
-
Product
Multi-Functional Graph Creating Software
OC-1300 series
-
The OC-1300 series makes it possible to create reports smoothly and easily to anyone from huge amount of data. You can layout axis freely on a graph by dragging mouse and create graph easily. Thanks to the improvement of user-interface, the new OC-1300 series achieves efficient processing of more diversified works.
-
Product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Multifunction Substation Test Set
STS 4000
-
STS 4000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers, designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
Multifunction Calibrators
-
Easy-to-use Multipurpose instruments for advanced documented calibration and process control.
-
Product
Multifunction Voltage and Current Calibrator
MC140i
-
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
Product
Multi-Function DAQ
-
Full spectrum of DAQ cards provides analog input and output, digital input and output, and counter/timer circuitry.
-
Product
PCI-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO PCI Multifunction I/O Device
779546-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO PCI Multifunction I/O Device - The PCI‑6255 offers analog I/O, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Reflection Meter
RC-088
-
This instrument is a special equipment for measuring the reflectivity of rearview mirror (or similar product) of motor vehicle. The product composes intelligent measuring instruments, optical integrating sphere, parallel lamp, standard light source, constant current source etc. It is easy to operate，it can measure the reflectivity quickly and accurately. On instrument structure, it adopts standardized modulation design. It takes latest single chip as its digital central processing element. After the measuring signal is converted by modulus, CPU will do some computation and compensation. The instrument can display the reflectivity of device which is measured in rear time. It operates simply and quickly, the indication is direct and accurate. It’s good for quality examination &control in the production scene as well as laboratories. This product has the convenience &quick demarcation way, can meet requirement of different occasion. It is applicable for measuring light reflection on mirror and not mirror parts.
-
Product
Analog Optical Power Meter - PXI
Power 1500 Series
Power Meter
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
