Variable Optical Attenuators
Adjust the power of an optical signal.
-
Product
Optical Attenuators
-
Guilin GLsun Science and Tech Group Co., LTD
Optical Attenuators by GLSN
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Voltage Variable Attenuators To 16 GHz
-
Our family of voltage controlled attenuators is non-reflective, with ranges of 32 dB of 64 dB. Pin diodes are used and the frequency range is 0.25-16 GHz. They operate with a control voltage of 0 to +8 VDC and handle +27 dBm maximum input power. These attenuators are bi-directional: either SMA port may be used for an input.
-
Product
Variable attenuator
-
Optimum for simulation of wireless communication equipments, such as handover test, dynamic motion test and receiving sensitivity test. Moreover, optimum for the simulation of the receiving trouble by the rainfall attenuation in BS/CS digital broadcasting.
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
PXI Dual RF Attenuator 63dB in 1 dB steps
41-180-022
Attenuator
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module.
-
Product
65 GHz Dual Channel Optical Module
N1030B
Optical Module
The N1030B is a plug-in module for the DCA-X mainframe that includes two 65 GHz optical channels.
-
Product
1x13 Optical Switch
N7734A
Optical Switch
The N7734A is a 1x13 fiberoptic switch, available for single-mode or multimode fiber connections. These enhance accurate measurements and ease automation with excellent repeatability, fast switching time and flexible interfacing with LAN, USB and GPIB.
-
Product
Voltage Controlled Variable Attenuators
-
A voltage variable attenuator is an electronic device that provides a variable attenuation depending on the voltage applied
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
Short Range Straightness Optics
10774A
Optical Module
The Keysight 10774A Short Range Straighness Optics combines a straightness interferometer and reflector to make measurements over a range of travel up to 3 m (10 ft). The optics form a highly-accurate optical straightedge that can measure the straightness of travel of machine-tool and measuring-machine coordinate motions with a resolution of 0.04 micrometer (1 uin).
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8493B
Attenuator
The Keysight 8493B coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Broadband Optical Source - MATRIQ
Optical Source
Our SLED MATRIQ instrument is a compact super-luminescent LED light source with high output power, large bandwidth and low spectral ripple.The SLED comes in various wavelength models to address various key applications across telecom and datacom, and is ideal for building a customized optical testing platform that delivers reliable and repeatable results.
-
Product
Programmable Step Attenuator, DC to 50 GHz, 60 dB, 10 dB steps
84905M
Attenuator
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
-
Product
Aging and Optical Attenuation Tester
LS822
-
• Build-in DC Power Supply: Forward current preset: 0.1-800mA (special order) Range of forward voltage: 0.1-20.00V • Range of luminous intensity: 1mcd-3,000cd • Range of luminous flux: 1mlm-9,999,000lm(depends on the size of sphere) • Accuracy of photometer: class1; accuracy of electricity: class0.5 • Aging time: 9999Hours 59Munites 59Seconds • Tolerance of time: ±1S/10H • Record time: 16000times • Hold data automatically when the power is off and continue to work automatically when the power is turned on.
-
Product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
Optical Switch
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
Product
Step Attenuator
RSC
Attenuator
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, Single Ended
7-414845000-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, Single Ended.
-
Product
Fixed Attenuator
FAXE
-
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
Product
Variable Gain Amplifiers
-
50 dB Gain, 14 dBm P1dB, 100 MHz to 18 GHz, Rack Mount, Variable Gain Amplifier, 6.5 dB NF, SMA
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
Product
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST
7-415804506-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST.
-
Product
RF Attenuators
-
Over 400 coaxial, surface mount, and MMIC attenuator models for 50-Ohm & 75- Ohm syetem including fixed attenuators, high-power attenuators, digital step / programmable attenuators, voltage variable attenuators and more. DC passing and DC blocking models. Power handling up to 100W. Bandwidths spanning DC to 50 GHz.
-
Product
RF Attenuators
-
Home > Products > Test and Measurement > AttenuatorsBird - The RF ExpertsRF AttenuatorsBird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
Variable Tone Generator
-
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
-
Product
SMA Rotary Attenuator
WATT-6SR1211
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
CAT-5 Video Variable Filters
-
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
