RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
Signal Module
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
PXI/PXIe RF Matrix, 32x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-022-L
Matrix Switch Module
The 40-724-022-L (PXI) and 42-724-022-L (PXIe) are 32x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, MCX
42-875A-101
Multiplexer Module
The 40-875A-101 (PXI) and 42-875A-101 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 8x4 RF Matrix 300MHz 50 SMB With Loop-Thru
40-729-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, MCX
40-837A-102
Matrix Switch Module
The 40-837A-102 (PXI) and 42-837A-102 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
RF Filters
-
RF Filters block unwanted frequencies when testing electronic devices for emissions during EMC testing. They attenuate unwanted frequencies and allow the desired signals through. The RF filters isolate the device under test from external RF noise, this increases the reliability and accuracy of the EMC testing by preventing out-of-band noise and harmonics.
-
Product
RF Chamber
HDRF-CHM-SERIES
-
*RF Chamber Designed and Developed for WLAN , Wireless device testing.*Ideal RF Enclosure for 802.11a, b, g, n, ac Device Testing*Ideal RF Shield for Bluetooth, RFID, 3G Device testing
-
Product
PXI 16x4 RF Matrix 300MHz 50 Multiway Connector With Loop-Thru
40-727-002-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-004
Multiplexer Module
The 40-876A-004 (PXI) and 42-876A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
Programmable RF Multi-Port Test
-
A programmable multi-port switch between your RF device under test and a Vector Network Analyzer significantly speeds up testing.
-
Product
RF Adapters
SMPM Adapters
-
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
Product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, MCX
40-872A-101
Multiplexer Module
The 40-872A-101 (PXI) and 42-872A-101 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
MS-M 26-Pin RF Cable Assembly, Female to Unterminated, 2m, RG316 Cable
40-979A-526-3-2m-FU
Cable Assembly
This 2m long MS-M RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the mating connector.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
Single 32 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-767A-001
Multiplexer Module
The terminated single 32 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
RF Limiter, 10 Hz to 1800 MHz
11867A
Power Limiter
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
Product
RF Technology And Design
-
RF technology is key to many aspects of electronics these days. With many systems from cellular to other wireless technologies including, Wi-Fi, WiMAX, NFC, RFID, and many other systems using RF signals.
-
Product
Single 8 to 1 50 600MHz PXI RF Multiplexer
40-762-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Custom Radio Frequency (RF) Receivers & Sources
-
FLO – Frequency Locked Oscillators, IFM – Instantaneous Frequency Measurement, DCU – Digital Control Units, ACU – Antenna Control Units, IDCU – Integrated DCUs, and Other Custom Products
-
Product
MS-M Style 3-Pin RF Cable, Female To SMB, 1m, RG178 Cable
40-979-503-1m-SMB
Cable Assembly
This 1m long MS-M style RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M style connector to the associated product.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, MCX
40-875A-101
Multiplexer Module
The 40-875A-101 (PXI) and 42-875A-101 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 8x4 RF Matrix 100MHz 75 SMB
40-729-101
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Dual 4 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-761-002
Multiplexer Module
This terminated dual 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI Single 4 to 1 RF Multiplexer 2GHz 50 Ohm SMA
40-745-521
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz. They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.
-
Product
Wireless Camera Detector / RF Signal Detector
SH-055SV / 10127
-
"This RF Signal Detector / Wireless Camera Detector / Cellular Phone Detector / Bug Detector" can detect the popular wireless CCTV camera, wireless phone, wireless tap and Cellular phone from 50 MHz ~ 6.0 GHz
-
Product
Microwave and RF Switching Systems and Drivers
CXM Series
-
This series is typically used for frequencies from DC to 40 GMHz. We use microwave relays, splitters, programmable attenuators and many other microwave components from the worlds most popular vendors to build standard or custom systems to your specifications. There are a large variety of 1x2 through 1x12 microwave relays available in Normally Open, Failsafe, Latching, Terminated or special configurations to suit your needs. Or simply buy the driver chassis and use it to control your own components. Since Cytec doesn"t build microwave components we can put the systems together with whatever parts you prefer and stand behind the warranty for you.
-
Product
MiniPCI Express 4-Way RF Combiner
SKU-089-13
-
MiniPCI Express 4-way RF Combiner. It allows combining signals from 4 antennas to a single antenna. The Adapter is a passive device and can be installed in any full size MiniPCI express circuit. This Adapter was designed for our Squid PCI express Carrier boards.
-
Product
RF Plasma Power Systems
-
These are ideal solutions for plasma apps like etching, cleaning, deposition and more
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
