Temperature Humidity Loggers
Record measurements of water vapour and temperature.
See Also: Loggers, Pressure Loggers, Current Loggers, Dataloggers, Humidity Loggers, Temperature Loggers, Voltage Loggers, Wireless Data Loggers, Wireless Loggers, Data Loggers
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7311
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.
-
Product
uSD Logger Shield
IFB-11001
-
This micro SD logger shield enables time-stamped logging of any signals measured by your Arduino project! Whether sensor shields, breakout boards or datalink connections, this shield will get your logger project up and running quickly. We've included an MCP79410 Real-Time-Clock module for flexible supply voltage timekeeping, which includes an on-board battery holder for a CR1220 battery (included, and is installed). In addition, the micro SD card is interfaced through a high-speed translator IC and supplied with a high-current LDO to meet the demands of the SD standard. Each pin of the Arduino has an offset pin attached for easy wiring to the massive 13x9 pin prototyping area, including the pins connected to the ICSP header! Whether you're using a Mega, Due or Uno, this board has your interfacing needs covered! Finally, the micro SD holder is a push to lock, push to unlock type, which makes it really easy to both install and uninstall your card.
-
Product
PXIe High Density Matrix Module, 128x2, 1-Pole, 2A, 60W, Extended Temperature
42-584A-001-ET
Matrix Switch Module
Our model 40-584A, along with the following models 40-585A, 40-586B and 40-587A are high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. This module is also available in PXIe format (42-584A-001).
-
Product
Logger and Handheld Instruments for Temperature Measurement and Monitoring
-
Temperature measurement and monitoring is vital for the quality of temperature-sensitive products wherever they are studied, produced, stored or transported.
-
Product
Combined Temperature – RH probe
HP474ACR
-
Combined Pt100 temperature and %RH probe, complete with SICRAM module.
-
Product
Temperature and humidity outdoor, indoor probe
T3110
-
Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.
-
Product
Temperature Forcing System
-
Wewon Environmental Chambers Co, Ltd.
Wewon Technology specializes in the research, development, production and sales of laboratory testing equipment system services. Through more than ten years of accumulation in the field of equipment, the business of wewon Tech is mainly divided into three fields, namely optical communication, automobile and new energy industry.Specialized equipment from Wewon Environmental Chambers Co., Ltd. includes thermal stream instrument, environmental chambers, walk in chamber, salt fog test chamber, vibration testing machine, xenon lamp aging tester, ultraviolet weather testing equipment, tensile testing machine and various IP protection level test equipment. The system characteristic of Wewon Tech thermal stream temperature test system as below technical parameters mentioned.https://www.wewontech.com/temperature-forcing-system/
-
Product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E001
Thermocouple Contact (ITA)
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
PRO+ 2-in-1 pH and Temperature Meter
MW102
-
The Milwaukee MW102 PRO+ pH meter has won fans around the world with its reliable, fast and simple operation as well as its toughness. Accurate to ± 0.02 pH with automatic temperature compensation. Ideal for use by brewers, wine makers, growers and other users with challenging pH measurement needs.
-
Product
Wireless Data Logger System
HD35
-
Wireless datalogging system allowing the monitoring of a multiplicity of physical quantities in the most diverse fields of application. Temperature - Humidity - Atmospheric and differential pressure - Illuminance - Irradiance UVA, UVB, UVC, CO, CO2 - Solar radiation - Precipitation - Wind speed and direction, Leaf wetness, Volumetric soil water content, Level, WBGT.
-
Product
The Field Logger
-
The Field Logger is a stand-alone data logger which is capable of recording potential vs. time and LPR vs. time data. The instrument is battery powered and records data onto an attached SD memory card. The instrument is entirely contained within a waterproof (IP67), tough polycarbonate enclosure (23x19x11cm), with probe connection via a single high quality watertight Lemo or Amphenol connector.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Local Discomfort Temperature Probe
TP3227PC
-
Temperature probe composed of 2 independent probes, Pt100 sensor, used for measuring local discomfort due to vertical thermal gradient.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
Product
Temperature Transmitter
T4411
-
Temperature transmitter for Pt1000/3850ppm sensor is built in a durable watertight case. Degrees Celsius and Fahrenheit are user selectable. Large dual line LCD is an advantage. Display is possible to switch off. Computerized design ensures maximum long term stability and failure indication.
-
Product
Temperature Transmitter Outdoor, Indoor
T0110
-
Temperature transmitter with 4-20mA output for two-wire connection is built in a durable watertight case. Output temperature range is user adjustable. Degrees Celsius and Fahrenheit are user selectable. Large dual line LCD is an advantage. Display is possible to switch off.
-
Product
Ultra Low Temperature Data Logging System
ULT90-9
-
MadgeTechs Ultra Low Temperature Freezer Validation System can measure and log data as low as -86°C. It can be placed in small and large freezers of varying configurations.
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
Transducers for Temperature
-
Overview of transducers with Ethernet interface for temperature and humidity.
-
Product
Temperature & Humidity Chamber
SG-H01T
-
This tester is used to determine the character change and the extent of strength deterioration of the shoe materials and sole under the high temperature and high humidity. It's also used to assess the discorloration and shrinkage of the leather productors under the simulate environment in container. It's specially used in testing the character of heat-endurance, cold-endurancer, drought-endurance and wet-endurance for various materials
-
Product
Data Loggers
-
Scientech Technologies Pvt. Ltd.
Onset data loggers and weather stations are used in a broad range of indoor, outdoor and underwater applications.
-
Product
RTD Based Temperature Data Logger
RTDTemp101A
-
The RTDTemp101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art datalogging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
Temperature Transmitter
P0212
-
The P0212 transmitter with 0-10 V output is designed for temperature measurement in air condition ducts. In combination with a thermowell is thetransmitter suitable for temperature measurement of liquids in tubing.
-
Product
Temperature Logger for PT100 Probe-50 to +300/600C
TV-4104
-
This data logger uses an external PT100 probe to record high temperatures. Probes are available to measure up to 300 and 600C. These are listed in the 'You will also need' section. The PT100 probes are of 3-wire construction and use class A elements.
-
Product
Low Level, DC Voltage Data Logger
Volt101A
-
The Volt101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
Universal, Dual Input, High Performance HART Temperature Transmitter
SEM310 MKII
-
The SEM310 is a universal programmable HART temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal
-
Product
Multi-Sensor Core Logger
-
The Geotek Multi-Sensor Core Logger (MSCL) systems enable a suite of geophysical measurements to be obtained rapidly, accurately and automatically on sediment or rock cores. The rugged nature of the equipment makes it suitable for use in either an onshore laboratory/repository environment or onboard survey and drilling vessels. All of Geotek’s core loggers accept core between 50 mm and 150 mm in diameter and up to 1.55 m in length. Geological cores and materials come in a variety of sizes therefore the MSCL and X-ray CT systems are designed for a full range of core material in a variety of liner compositions. To accommodate varying customers’ requirements (both operational and scientific), we provide a range of different core loggers and X-ray CT systems:
-
Product
Data Logger
MS6D
-
Data loggers are designed for measuring, recording, evaluation and subsequent processing of input electrical signals, which are subject to relatively slow changes (> 1s). In conjunction with the appropriate sensors and transducers are suitable for monitoring physical quantities.
-
Product
Humidity Sensor Components
-
Based on a unique capacitive cell, our temperature and humidity sensors are designed for high volume applications where humidity measurement is needed.
-
Product
Temperature Measurement IR Sensors & Detectors
1M
-
A thin film-based thermopile with a 1.0mm diameter active area with good signal-to-noise ratio in a TO-5 package and a moderate time constant of 32ms with Argon encapsulation gas.
