Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
-
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) HDMI
510171113
PCB Adapter (ITA)
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) HDMI.
-
Product
Vacuum Test Adapter
-
Vacuum test adapters (VA) are suitable for contacting electronic assemblies with large quantities (mass testing) and a small number of variants. INGUN vacuum test adapters are available as standard as a single system without an exchangeable replacement kit.
-
Product
True RMS Clamp Meter w/ Pipe Clmap Adapter
DL489COMBO
-
UEi Test & Measurement Instruments
True RMS Clamp meter and 2 ATTPC3 pipe clamp adapter, 2 ATT29 K-Type temperature probes
-
Product
MCB Test Option, Monitor Voltage Adapter
PTE-FCB
-
The PTE-FCB / PTE-FCD can be used to effectively reduce the sensitivity of the monitor input. The monitor input detects the relay’s operation and stops (or starts) the chronometer when testing with the PTE-100-C, PTE-50-CE, PTE-50-CET, and all LETs excluding the LET-400 (which lacks a chronometer).
-
Product
RF Adapters
BNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
Product
100MHz DDS Signal Generator
408A
-
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Milk Analyzers
-
Measuring parameters: FAT 0.01% - 25%SNF 3% - 15%Density 1015 1040kg/m3Proteins 2% - 7%Lactose 0.01% - 6%Water content 0% - 70%Temp. of milk 1C 40CFreezing point - -0.400 0.700CSolids 0.4 1.5%1. Sample visualization onLCD display(green)2. Possibility to measure 1 sample 90 seconds(option 60 seconds)3. Adapter 220-110 V 4.Spare silicone tubes5. Syringe6. Plastic sample holder7. Calibrations Cow, Sheep, and UHT milk8. Operation Manual9. Cardboard transport case10. CD Service PackMeasuring time 30s
-
Product
Test Adapter / Pneumatic Adapter
-
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
Product
DVB-T SFN Adapter
MIPDVB
-
MIPDVB for HDc is ENENSYS’ SFN adapter module for DVB-T that inserts synchronization data to enable Single Frequency Network broadcasting.Running at the head-end after DVB multiplexer, the MIPDVB runs in the HDc chassis to embed up to 6x MIPDVB modules in 1U so that the same chassis can output up to 6 TS with MIP packets over ASI or IP.
-
Product
Adapter, 1.0 Mm (m) To 1.0 Mm (f), DC To 120 GHz
Y1910C
-
Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
I2C High Speed Interface for USB
telos Tracii XL
-
telos EDV Systementwicklung GmbH
Tracii XL is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 2 Mbit/s. Additionally Tracii XL can work as an I2C monitor.
-
Product
Adapter/Stainless Steel
WADP-24F24F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PMC-to-PCI Express Adapter
4733
-
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
Product
High-Speed Multi-IO SPI Host Adapter
BusPro-S™
-
The BusPro-S High-Speed Multi-IO SPI Host is designed with speed, versatility, and value in mind. Featuring a 60 MHz clock rate with up to 200 Mb/s throughput and support for standard, dual, quad, and 3-wire modes, the BusPro-S is the right tool for all SPI debugging applications-present and beyond.
-
Product
Coaxial Adapter, 3.5 mm (f) to 3.5 mm (f), DC to 26.5 GHz
83059B
Contact Adapter (Receiver)
The Keysight 83059B instrument-grade 3.5-mm female to 3.5 mm female coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
-
-
Product
Adapter, 1.0 Mm (f) To 1.0 Mm (f), DC To 120 GHz
Y1910B
-
Y1910B Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 120 GHz provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
PCIe Adapter for PMC
PCIeBPMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
RF Adapters
N-Type Adapters
-
One of the most important classes of radio frequency adapters as they are often used to bring radio frequency connectivity outdoors.
-
Product
External Contact Adapter
DT141
-
This MicroLog sensor monitors Reed Relay contacts and switch status (open/closed), to identify the correlation between phenomena such as temperature change and door status.
-
Product
SSOP-to-DIP Adaptor
Series 351000
-
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Adapter/Stainless Steel
WADP-QSMSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
PCB Adapter
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
Machine Vision Camera - 7.1 MP, 112 FPS, Sony IMX420, Color, with 10GigE Adapter
Oryx 10GigE
-
The award-winning Oryx 10GigE camera family allows systems designers to take advantage of the latest sensors by supporting transfer speeds of up to 10 Gbit/s enabling capture of 4K resolution, 12-bit images at over 60 FPS. Oryx features include IEEE1588 clock synchronization and full compatibility with several popular third-party software supporting GigE Vision. Reliable image transfer at high bandwidth is further improved with Myricom bundles and packet resend feature. Oryx’s 10GBASE-T interface is a proven and widely deployed standard that provides reliable image transfer at cable lengths over 50 meters on inexpensive CAT6A, and up to 30 meters on CAT5e.
-
-
Product
Flexible MiniPCI Express to PCI Express Adapter
SKU-035-XX
-
The Flexible MiniPCI Express to x1, x4 or x16 PCI Express Adapter (Adapter) was designed to convert the MiniPCI Express bus into x1, x4 or x16Express bus and extend it. It allows you to connect a x1, x4 or x16 Express expansion add-in board to the motherboard’s MiniPCI Express connector.The Adapter includes an x1, x4 or x16 PCI Express adapter board, MiniPCI Express host board (full-size or half-size) and a PCI Express flat Cable.
