Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
NI-9231, 8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module
783610-01
-
8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module - The NI-9231 is a high-density sound and vibration module that can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. It can perform the high dynamic range measurements necessary for modern measurement microphones and accelerometers and features simultaneous sampling. The NI-9231 incorporates both a TEDS input path and 2 mA of IEPE signal excitation source that can be turned on and off, removing the need for external sensor power and reducing the complexity of the data acquisition system.
-
Product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
-
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Source Measure Units
NGU
-
Thanks to their extremely high accuracy and fast load recovery time, the R&S®NGU source measure units (SMU) are perfect for challenging applications. A special ammeter design is used to precisely measure current drains from nA to A in one pass – no need to make multiple measurement sweeps. The instruments’ short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. With high speed data acquisition, every detail is detected down to 2 μs resolution.
-
Product
CPCI Integrated Communication Card
MS 3635I
-
CPCI Integrated Communication Card is high end Microprocessor based Mixed RS422 Communication and Differential Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have Synchronous RS422 Communication Interface, Asynchronous RS422 Communication Interface, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic storage and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
PXI Very High Density MUX 5 Chan 32 Pole
40-675-002-5/32
-
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI High Density Multiplexer, 20-Bank, 8-Channel, 1-Pole
40-615A-001
-
The 40-615A-001 is a 20-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single 32x8 Matrix, 1 Pole Screened
40-531-021-S
-
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PCI High Density Screened MUX 49 Ch 2 Pole
50-670-021-S-49/2
-
The 50-670 series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670 shares exactly the same architecture as the established PXI 40-670 module.
-
Product
USB OEM Data Acquisition (DAQ) Products
-
ACCES now offers USB-based data acquisition and control in both standard packaging and embedded OEM USB/104 board only options. These USB devices are perfect for a variety of applications requiring monitoring, control and industrial serial communications. USB is by far the most popular and compatible standard data interface for direct PC connection. Add the features you need in your application in hours, not days. Choose from over 100 different models and options (including extended temperature) encompassing analog I/O, digital I/O, counter/timer, and serial I/O configurations. Experience simple and immediate connection to any PC or embedded system with a USB port.
-
Product
PXI 2A Multiplexer, 2-Bank, 4-Channel 16-Pole
40-614-014
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.827-02
-
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, 1 Meter
187252-01
-
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781445-01
-
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
1U 18" Short-Depth Edge Server
HPC-6120+ASMB-610
-
1U 18" short-depth edge server with Intel® Xeon® W CPU, 128GB DDR4, and 4 PCIe slots. Designed for reliable edge AI, automation, and data acquisition.
-
Product
PCI Multifunction Board
PCI-1602F/8K/S
-
The PCI-1602/1602F series is a family of high performance and high resolution data acquisition boards for the PCI bus. It features a continuous, 100KHz for PCI-1602 (200KHz for PCI-1602F), gap-free data acquisition under DOS and Windows. The PCI-1602 family has the same hardware architecture as PCI-1802L. The PCI-1602 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1602 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
DAQ FMC Modules
-
Sundance Multiprocessor Technology Ltd.
FMC Modules with both Analog to Digital and Digital to Analog sections.
-
Product
Dual Channel Variable Filter
4302
-
The Model 4302 Dual Filter is a high performance, low priced, general purpose filter for use in the laboratory as well as in multiple channel data acquisition applications.
-
Product
Measurement and Control Card
PCIe BASE
-
Stationary measurement data acquisition in the latest "PCI-Express" technology: The PCIe-BASE is a multifunctional measurement and control card whose modular structure guarantees individual and flexible adaptation to a measurement application.
-
Product
Geoelectric Power Sounder
GEPS-2000
-
Geoelectric Power Sounder GEPS-2000 is a device for data acquisition and interpretation of deep VES (vertical electrical sounding) as well as for 8 channel profiling (resistivity and IP sections). It can be used for measurements up to 1000 – 2000 m depth allowing both high voltage and high current injection of transmitter current according to real measuring conditions.
-
Product
Chemiluminescence Ammonia Analyzer
Model T201
-
The Model T201 combines a specially configured chemiluminescence analyzer with an external thermal converter to give stable and repeatable NH3 measurements at very low levels. In addition, the T201 provides simultaneous values for NO, NO2, and NOx concentrations. The T201 is ideal for trace ammonia monitoring applications in ambient air as well as in clean rooms and make-up air units. Optional zero and span valves allow automatic, unattended calibration checks.The Model T201 achieves its remarkable stability by means of an AutoZero valve which measures and corrects for zero noise. Multiple self-checks are performed continuously to insure maximum up-time while an innovative sample path, plumbed with specially conditioned materials, preserves the NH3 sample and reduces interferents to a minimum. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports either locally or by remote connection.The Model T201 comes with the Numaview™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
Firmware Engineering Projects
-
Precision Development Consulting Inc
Hand control module for teleprompter, Analog data acquisition and filtering, High-Power Arc Lamp Power Supply Controller and RTP gas flow and Vacuum System controller, Disk drive company test racks, Disk Drive Spindle Motor Tester, Disk Drive Head Stack Tester, Wafer photoresist coating and development system control PC boards, Nuclear Plant secondary water temperature monitor
-
Product
Optical Multiport Power Meter
N7745C
-
Keysight's popular N7745A optical power meters with eight power-sensor channels provide increased throughput and operational efficiency to meet today's challenges in manufacturing. Designed for characterizing optical multiport components, these optical power meters offer industry-leading solutions for device connectivity, high-speed measurement data acquisition and fast data transfer for post-processing. The multiport power meter enables fast measurement solutions for all multiport devices; for example multiplexers, PON splitters, wavelength selective switches (WSS) and ROADMs, as well as compact setups for simultaneous testing of multiple single-port devices.
-
Product
Vibration Analysis Software For Squeak & Rattle Testing
MB BSR Suite
-
MB BSR SUITE is the complete solution for all measurement tasks in the field of NVH, Squeak & Rattle and Sound Quality testing. Comprehensive analysis and assessment capabilities also enable the use of the BSR Suite for analysis and evaluation of functional and operating noise, vibrational effects on humans as well as the acoustic and haptic feedback of controls and actuators. Predefined test configurations for typical tasks such as multi-channel road load data acquisition, drive-file generation and objective Squeak & Rattle and Sound Quality testing allow for fast and simple operation. Signal statistics and user defined thresholds or reference-curves can be used for objective evaluation of different acoustic or haptic quality criteria. In addition the development and integration of application- or customer-specific analyses and evaluation methods is also possible at any time. Contact MB to find a solution for your measurement task!
-
Product
PXI Very High Density Multiplexer, 49-Channel, 4-pole
40-670C-022-49/4
-
The 40-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
Multiple-Input Multiple-Output (MIMO) FRF Testing
-
EDM Modal MIMO FRF Testing includes a dedicated test setup and operation process flow using multiple simultaneous shakers to acquire FRF signals. Using a large channel count data acquisition system (i.e., Spider- 80X or Spider-80Xi), this shaker excitation method provides much higher efficiency and accuracy for the FRF measurements while minimizing local stresses on the test article.
-
Product
PXI 2A Multiplexer, 1-Bank, 16-Channel 8-Pole
40-614-018
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Oscilloscopes And Digitizers
-
NI oscilloscopes and digitizers are precision modular instruments for capturing and analyzing electrical signals in automated test and high-channel-count systems. Oscilloscopes provide interactive, real-time visualization and measurement, ideal for debugging and design validation, while digitizers deliver high-speed, deep-memory data acquisition for advanced analysis and long-duration recording through software control with fully user-programmable FPGA.
-
Product
WiFiScope WS6: 500 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-500XM-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
