Oscilloscopes
Analyze waveforms of electronic signals by producing a trace on a display screen of corrosponding oscillations of voltage and current.
See Also: Scopes, Fiberscopes, Microscopes, Borescopes, Endoscopes, Stethoscopes, Stroboscopes, Synchroscopes, Telescopes, Vectorscopes, Analog Oscilloscopes, Digital Storage Oscilloscopes, Oscilloscope Probes, Waveform, Digitizers
-
Product
2.5 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Oscilloscope
WavePro 254HD
Oscilloscope
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s. Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector. MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms. Zone Trigger – Simple Triggering for Complex Signals.
-
Product
Probe Adapters
-
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
Product
Oscilloscope 200 MHz, 4 Analog Channels
DSOX3024G
Oscilloscope
The DSOX3024G 200 MHz oscilloscope provides 4 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Oscilloscope, 350 MHz, 2 Input Channels, 2 GS/s interleaved, 14 Mpts/Ch
T3DSO1302A
Oscilloscope
350 MHz, 1 GS/s per Ch, 2 GS/s interleaved, 2 CH, 14 Mpts/Ch DSO with 7" Color Display.
-
Product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
-
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
PXIe-5172 PXI Oscilloscope, 100 MHz, 14 bits, 250 MS/s, 4 Channels, .75 GB
784224-01
Oscilloscope
PXIe, 100 MHz, 4- or 8-Channel, 14-Bit, Kintex-7 325T or 410T FPGA Reconfigurable PXI Oscilloscope—The PXIe 5172 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling and voltage range. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 250 MS/s or 100 MHz of analog bandwidth and advanced PXI synchronization.
-
Product
Digital Oscilloscope
MOSTs5
-
MOSTS5 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent galvanic isolation channels.MOSC5, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
Product
3-3/4 Digits GRAPHICAL MULTIMETER
IBL-33N
-
International Biological Laboratories
This data logging graphical multimeter is a combination of a 3-3/4 Digits True RMS Multimeter with 200kHz Digital Storage Oscilloscope that can store 15 waveforms or measurements.
-
Product
Handheld Oscilloscopes, 100 MHz, 2 Analog Channels
U1610A
Oscilloscope
100 MHz2 analog channelsTroubleshoot in any weather with channel-to-channel isolation and a CAT III 600 V safety ratingIdentify glitches easily with dual window zoomView subtle signal details more clearly with up to 1 Gsa/s sampling rate and 120 Kpts memoryDebug under any lighting conditions with 3 selectable viewing modes (indoor, outdoor and night vision)Get 3 instruments in 1: a dual-channel oscilloscope, built-in DMM and data loggerEasier start-up with 10 selectable languages
-
Product
Oscilloscope
RTM3000
Oscilloscope
Designed as daily problem-solving tool, the R&S®RTM3000 combines the power of ten (10-bit ADC, 10 times the memory and 10.1" touchscreen) with a Rohde & Schwarz probe interface for all Rohde & Schwarz probes.
-
Product
USB Oscilloscope
P9242A Keysight Streamline Series
Oscilloscope
Compact, faceless, USB oscilloscope using Keysight’s InfiiniVision technology. Available at 500 MHz and 5 GSa/s. Offers a small footprint and mobility.
-
Product
400 MHz High Voltage Passive Probe
HVP120
-
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
Product
Voltage Probes
-
An oscilloscope is only as good as its probes. Our range includes high voltage, differential, active, low capacitance, and passive types, with ranges to 30kV and frequency bandwidths to 5 GHz.
-
Product
VirtualBench All-in-One Instrument
-
The VirtualBench All-in-One Instrument combines a mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O. The all-in-one features are simple, convenient, and provide more efficient circuit design, debugging, and validation. The included software lets you view all measurements on a single screen and can be updated with free software releases to add functionality and value. The VirtualBench All-in-One Instrument easily integrates with LabVIEW software to provide programmatic control and automated test sequences.
-
Product
Digital Oscilloscope
MSO5000-E
-
Mso5000-e series digital oscilloscope is based on the technology of RIGOL ultravision II, which is a high-performance and economical digital oscilloscope specially designed for professional engineers.
-
Product
SRJ (for IBP sensors)
-
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
Product
Single-Channel Oscilloscope
PenScopeDAQ
-
Digital oscilloscope PenScopeDAQ is a single-channel instrument with maximum frequency of sampling 100MHz and resolution 8 bits. PenScopeDAQ is realized in pen-type housing. Connected to the USB cable PenScopeDAQ doesn't require an external power supply - it enables the user to use this tool in any design, service or automotive measuring tasks. This device is also offered with BNC connector.
-
Product
Mixed Signal Oscilloscope - 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154A
Oscilloscope
1.5 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
1.5 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1500 is ideal for 1 GHz and lower oscilloscopes.
-
Product
Oscilloscope
RTC1000
Oscilloscope
High sensitivity, multifunctionality and a great price - that is what makes the R&S®RTC1000 oscilloscope so special. From embedded developers to service technicians to educators - the wide range of functions address a broad group of users. State-of-the-art, high-performance technology in a fanless design meets the high requirements of today's customers.
-
Product
Life-time Measurement System For Silicon Bulks / Ingots With Non-contact
HF-90R
-
*Silicon bulk, Prismatic shape (JIS code), Ingot condition*Non-contact photoconduction vibration decay method*Data processing by digital oscilloscope and PC with software
-
Product
Digital Storage Oscilloscopes
-
Scientific Mes-Technik Private Ltd
Digital Storage Oscilloscopes
-
Product
WaveMaster Oscilloscope, 13 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 813Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
Mixed Signal Oscilloscope - 1 GHz, 2 Analog Plus 16 Digital Channels
MSOX3102T
Oscilloscope
1 GHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Mixed Signal Oscilloscope, 500 MHz 2 Analog Plus 16 Digital Channels
MSOX3052A
Oscilloscope
500 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
÷10, 500 MHz, 10 MΩ, Passive Probe (Total of 1 Per Channel)
PP008-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Mixed Signal Oscilloscope - 200 MHz, 2 Analog Plus 16 Digital Channels
MSOX3022T
Oscilloscope
200 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Analog Oscilloscope
PS-500
-
*50MHz Vert. Band width*Sweep Time 23 Steps*Dual & Trace, ALT Trigger*Hold-off, X-Y operation*High Vert, Sensitivity : 1mv/DIV*High Sweep Resolution : 10ns/DIV
-
Product
Mixed Signal Oscilloscope: 16 GHz, 4 Analog Plus 16 Digital Channels
MSOV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
PXI Quad 4 to 1 Mux 1.3GHz 50Ohm SMB
40-749-511
Multiplexer Module
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
