I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
Speed Switch
SCP1000/SCP2000
-
Features• Internal sensor• Over-or under-speed config., 1-990 rpm• 1 DPDT relay output (SCP1000), 2 SPDT relay outputs (SCP2000)• Built-in start delay• Dial-in calibration does not require power• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs / wraps• Explosion proof housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
DC/DC Converter 150 W
CQB150W-110S3V3
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 3.3 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
-
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Alternate 2.82 (80.00) - 5.00 (141.00) General Purpose Probe
HPA-74T75-1
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
Product
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
510104160
-
These 5 position pneumatic modules are made with G10 Epoxy glass and can withstand temperatures of 140°C.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
DC/DC Converter 120 W
CTS-120-6874-D
-
DC/DC converter with 120 W from Premium | input ranges 43.2 - 90 VDC | output 12 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Calibration Solutions
-
Calibration buffer solutions and deionized water are pre-mixed and color-coded to prevent errors. Ideal for calibrating electrodes and pH meters and are accurate to within ±0.01 pH at 25°C (77°F).
-
Product
Mixed Signal Oscilloscope
QA101B
-
Up to two analog Channels, 70 MHz bandwidth10-bit ADC5mV/div to 5V/div, +/-50V max (CAT I use on non-hazardous/non-lethal voltages only)Up to 24 logic analyzer channelsMixed Modes:2 10b Analog Channels, 12 Logic Channels, up to 100 MSPS1 8b Analog Channel, 12 Logic Channels, 200 MSPS1 8b Analog Channels, 24 Logic Channels, up to 100MSPS
-
Product
NI-9421 , 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-01
-
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
On-Line Gas Analysis System
Titan-OL
-
The Titan-OL is a turnkey, process-ready gas analysis system. The analyzer and sample handling hardware can be wall or frame mounted in a NEMA enclosure suitable for use in production environments, including Class I, Div. 1. The integrated sampling system is fully purgeable and can handle multiple sample and reference lines.
-
Product
Crossed-Roller Bearing Linear Stage ,25mm Travel XY,Sensitivity 1um
NFP-2462
-
Model:NFP-2462Crossed-Roller Bearing Linear Stage ,25mm Travel XY,Sensitivity 1umDetailsSpec: Please refer to NFP-1462 Specification,It is combinated by2pcs NFP-1462(C,SR,SL)
-
Product
Handheld Instruments for Measuring Humidity & Temperature
-
Our range of handheld instruments are perfect for monitoring environmental conditions. Models with an interchangeable probe input have the wide measurement ranges -100…200 °C, 0…100 %rh with a Rotronic probe selected for the application.
-
Product
PMC FPDP Board
MS 1741
-
- Four FPDP front panel outputs- FIFO buffering for real−time recording- FPDP Outputs: Two 80−pin FPDP connectors (A and B)- FPDP Outputs: Two 80−pin FPDP connectors(C and D)- Quantity: Standard: Two Front Panel Data Port (FPDP) connectors, each providing 32−bit output- Output Type: FPDP I, non−inverted configuration FPDP II, double the selected clock rate- Clock: On−board clock- FIFOs- Quantity: Four IDT72V3690 FIFOs, one for each FPDP port- Size: 32,768 x 36- Speed: FIFOs are capable of 166 MHz speed, but are run at one half of sample clock speed
-
Product
NI-9211, 4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input Module
779001-01
-
4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input ModuleThe NI‑9211 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9211 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
Needle Microprobe
MT-26/6HT
-
Fast-response 26 gauge needle probe, (needle length is 6 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
Automatic Metallic Pendulum Impact Testing Machine
-
Jinan Testing Equipment IE Corporation
JB-450/750A automatic type pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and is capable of doing a large number of impact tests continuously. The automatic type pendulum impact tester can display the impact power, impact toughness, and the pendulum's rotation angle. All the testing reports can be printed out. JB-450/750A can be equipped with fully automated sample feeding system, which greatly improves the test efficiency, and reduce labor intensity. The crygenic cooling device is available for impact tests under the lowest temperature down to -196 C. The automatic type pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
-
Product
NON CONDUCT DIGITAL THERMOMETER
IBL-MT5
-
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 6 - 14 mm and measures temperature from -50 to 550 Degree C and also in Fahrenheit scale.
-
Product
AC/DC Power Supply 50 W
HBU50-109
-
AC/DC power supply with 50 W from Sinpro | input ranges 80 - 275 VAC | output 32 V | operates in temperatures from -10 to +70 °C | provides 2 MOPP protection
-
Product
Bench Power Supply, Calibrated, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL
-
The 72-2690 CAL from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
Product
Streamlined, Fanless, Expandable Edge Computing Platform With 13th Gen Intel® Core™ Processor
MXE-310 Series
-
The MXE-310 is a streamlined, fanless, expandable edge computing platform powered by the 13th Gen Intel® Core™ i7/i5/i3 processors. Designed for high performance in a compact form factor, the MXE-310 supports up to 64GB of DDR5 4800MHz memory and operates efficiently within a temperature range of -20°C to 60°C. It offers extensive connectivity options, including three monitor outputs (Type-C, DisplayPort, HDMI) and up to six LAN ports, making it versatile for various industrial applications.
-
Product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779373-01
-
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
Product
DC/AC Inverter 1500 W
ODS-1500-7117
-
DC/AC inverter with 1500 W from Premium | input ranges 77 - 138 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
Product
Cable Assy 9-Pin D-Type M/F 1M HV
40-970-009-1m-MFHV
-
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assemblycan be secured to the product by screwlocks.
-
Product
25µA Micropower Voltage References
ISL21070
-
The ISL21070 voltage references are analog voltage references featuring low supply voltage operation at ultra-low 25µA max operating current. Additionally, the ISL21070 family features guaranteed initial accuracy as low as ±0.2% and 30ppm/°C temperature coefficient. These references are ideal for general purpose applications for performance at lower cost.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-01
-
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
