Ethernet Test
Evaluation of a packet based ethernet network's wiring and signaling.
-
Product
Reflector
NetProbe 10GR
-
The NetProbe 10GR reflector provides loopback functionality in a low-cost, handheld device. It’s a smart loop device that swaps the source and destination addresses in MAC and IP headers as necessary to run Ethernet performance tests.
-
Product
Multi-Functional Ethernet Test Solution
PacketExpert™
-
PacketExpert™ 10GX is a comprehensive Ethernet/IP test solution supporting industry standard functionalities including wirespeed bit error rate testing (BERT), RFC 2544 / Y.1564 / RFC 6349 tests, packet capture, event-driven triggers and actions, traffic playback, impairment generation, stacked VLAN/MPLS tests, and many others.
-
Product
10Gbit Ethernet Test Engine
XGT-200
-
The Ethernet test engine XGT 200 provide a comprehensive test for next generation Ethernet solution. There are many different test modules, it can help clients to verify the performance of their Ethernet. XGT-200 have two 10/100/1000Mb/s RJ45 , two 100/1000M SFP and two 10Gbps SFP+ it can generate test profession streams that you need and analyze them ,then provide the test result. XGT-200 provide install and maintain services and activate new profession service. XGT-200 can provide many kinds of test functions, it can help you to control and know the quality of your Ethernet.
-
Product
Automotive Ethernet Testing
-
The automotive industry is evolving rapidly. The newest models have features that represent unparalleled innovation – cars that can communicate with each other, the road-side infrastructure, the Internet, plus highly advanced in-car infotainment systems. Cars are also being equipped with sensor-based safety systems that can dramatically improve traffic safety by virtually eliminating crashes. And we are nearing a point where fully automated vehicles that can handle all driving tasks will soon be commercially available.
-
Product
Automotive Ethernet Interface Device
Ethernet Interface
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
-
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
Product
Automotive Ethernet Tx Test Software 10M to 5Gbps
AE6910T
-
The E6960A 1000Base-T1 automotive Ethernet compliance application software for Infiniium Series oscilloscopes provides you with a fast and easy way to verify and debug your automotive technology designs.
-
Product
Flexible Test Coverage
Xcellon-Multis CXP 100/40/10GbE Load Modules
-
Keysight Network Applications and Security
Evolve Your Higher Speed Ethernet Testing
-
Product
Ethernet Speed Test Solution
NET-BOX™
-
The NET- BOX is an optimized Quality of Experience (QoE) testing platform that offers a low cost, reliable, high performance FPGA-based alternative to expensive high-end laptops often used for enterprise and speed tests. With a multi-test port architecture, with four 1GE, one 2.5GE test and 4 Gbps full line rate capability, the NET-BOX can truly test the limits to verify Quality of Service (QoS) and assure QoE for the ever growing high-speed internet service at and beyond 1 Gbps.
-
Product
E1 Testers
-
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
Product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
Ethernet Interface
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
Product
MirrorLink Test System
Catena 2210
-
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
-
Product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
-
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
Product
Functional Testing
-
Functional Ethernet testing is done during the research and development phase of a product or service. It can cover many parameters depending on the DUT and the application. Using Xena’s products, your range of functional Ethernet testing includes:*Multicast*40/100G PCS and PMA Layer*Transparent Transport*Energy Efficient Ethernet (EEE)*Microbursts and random IFG*Synchronous Ethernet*Automotive Ethernet*1588v2 Performance Testing*Regression testing*Kernel drivers and NIC testing*Hardware emulation (ASIC*)
-
Product
PXIe-8285, 2-Port, 25 Gigabit, RDMA PXI Ethernet Interface Module
788510-01
Ethernet Interface
The PXIe-8285 is a high-performance 25-Gigabit remote direct memory access (RDMA) interface for PXI Express. This module includes two 25-Gigabit Ethernet SFP28 ports in a single-slot PXI Express module and supports RDMA over Converged Ethernet (RoCE).
-
Product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
Ethernet Interface
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
Product
Ethernet Module
M4K-ETH
Ethernet Interface
The M4K-ETH is an intelligent Gigabit Ethernet interface module for the multiprotocol Excalibur 4000 family of carrier boards. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
Ethernet Interface
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
PXIe-8234, 2-Port Gigabit PXI Ethernet Interface Module
780244-01
Ethernet Interface
Vision Software Included, 2-Port Gigabit PXI Ethernet Interface Module—The PXIe-8234 with Vision Acquisition Software can acquire images from the fastest GigE Vision cameras. It transfers images at full Gigabit Ethernet bandwidth on both ports simultaneously, and it is optimized for extremely low CPU load. The PXIe-8234 with Vision Acquisition Software provides full GigE Vision bandwidth at every port, giving you the bandwidth you need for your most demanding vision applications. It also includes NI Vision Acquisition Software, which is driver software for acquiring, displaying, logging, and monitoring images from a multitude of camera types. With a set of easy-to-use functions and example programs, you can quickly create applications using LabVIEW, C, C++, C#, Visual Basic, and Visual Basic .NET.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Prototyping & Test Consulting Services Solutions
test
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
TestStand
test
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
NI HIL and Real-Time Test Software Suite
test
Suites combine LabVIEW Professional Development System with NI's most popular application softwareIncludes LabVIEW Professional, VeriStand, and the LabVIEW Real-Time and LabVIEW FPGA modulesEach new suite includes a one-year NI Training and Certification membershipSoftware is shipped on USB 3.0 media with NI device drivers included to speed up your installationConfigure real-time test applications quickly and easily; add custom functionality
-
Product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
Ethernet Interface
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
Product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
Ethernet Interface
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
Product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
Ethernet Interface
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
Product
FPGA UDP Packet Interface Connnecting 3-4 Channels of MIL-STD-1553 to Ethernet in Real-Time
ENETX-1553
Ethernet Interface
ENETX-1553™ is an innovative product that provides “remoting” of 1553 operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENETX-1553 is a small, low-power, rugged device that provides real-time Ethernet connectivity to for three or four dual redundant 1553 (A/B) buses (channels). Ideal for remoting 1553 connections for in-field applications or point-point lab usage. AltaAPI provides and highly portable BSD SDK and National Instruments LabVIEW and LabWindows. ENET products are unique in the market as they have a hardware, FPGA real-time UDP engine – no OS or IP stacks – provides maximum throughput and ultimate virus protection.
-
Product
1553 to Ethernet Converter
eNet-1553
Ethernet Interface
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
Product
HTOL Test Systems
Test System
Our IOL & Power-Cycling systems increase measurement quality & throughput while simultaneously reducing the Total Cost of Test (TCoT) of an open platform. We focus on complete monitoring and precise temperature control for each device under test.
