Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
-
Product
Load Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Load Measurement Trainer comprises of strain gauge based load cell,loading arrangement to load in compression, weights and digital load indicator to read the load in Kg.
-
Product
Resistive & Capacitive, Inductive AC Load Bank
RLC
-
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
Product
Internal Load Digital ESU Analyzer
ESU-2300
-
Measurements via Industry Standard Current Sensing Method. The ESU-2300 uses advanced ultra-high-speed waveform sampling techniques to accurately analyze even the most complex electrosurgery generator waveforms.
-
Product
High Precision Electronic Load
PEL-8000
-
PEL-8000 series adopts high-performance chip high-speed and high-precision design, providing resolution of 0.1mV, 0.01mA (basic accuracy is 0.03%, basic current rise rate is 2.5A / US)
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Automation Software For Aim-TTi Power Products Including LD And LDH Series Electronic Loads.
Test Bridge
-
Test Bridge software is a simple Windows application intended to make it possible to create a test sequence that can control up to four Aim-TTi products and record measurement results in graphical and tabular form.
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
Product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
Product
Load Washer
5000 Series
-
The Load cell is a stainless steel sub-miniature strain gage based transducer with compensated temperature performance. This type provides measurements up to 20000 lbf with better than ±0.5% (full scale) non-linearity
-
Product
Digital Load Calibrator
HS 2000
-
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
DC Electronic Load
EE30140A
-
The EE30140A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Built-in fans provide sufficient coolingSelf-contained unit eliminates hazards due to exposed wiringFine tuning mechanism allows for ultra precise measurementsUnits are on casters, providing a portable test station!
-
Product
48V / 300 Amp Load
BD18-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Hand-Held/Digital Load Tester
6030DV
-
• Full 125 Amp load Tests 12 Volt and 24 Volt batteries (DUAL LOAD) alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
AC Load Banks
XL1500 Series
-
Mosebach Manufacturing Company
The XL1500 Series of resistive load banks are designed for testing power supplies up to 1500kW of various voltages.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-23S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of terminal feeder
-
Product
Hand-Held Alternator/Battery Load Tester
6024
-
• Full 125 Amp load tests 12 Volt and 24 Volt Batteries, alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
Load Cells
-
Flintec load cells are highly accurate and built to last. We pride ourselves on the quality of our products and the service we provide.Our sensors are available globally. If your application requires a Custom Solution, our expert engineers can help.
-
Product
Signal Module, Receiver, QuadraPaddle, 90 Series, 480 Position, Fully Loaded with Twin Female Contacts and Square Posts for Wire Wrap (610 138 200 and 610 138 118)
510150147
Receiver Module
Primary mating module 510151106. (May mate with other ITA modules, as well.)
-
Product
AC Load Banks
-
Power House Manufacturing, Inc.
Hand carried AC load banks in any capacity to meet your load testing needs. Power House Manufacturing has developed the best ultra-compact and light-weight hand carried AC load banks. AC load banks with capacities unmatched in the industry.
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
Structural Load Monitoring
SLM
-
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
Product
Electronical Load Board 3U VME64x (air cooled)
056-921
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
Signal / Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/twin female contacts
510160112
Receiver Module
This module comes fully loaded with twin female contacts (p/n 610138200), iCon modules mount from the rear of the iCon/i1 receiver allowing installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
8 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 8 Ports
GPS802
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Unclamped Inductive Load Tester
ITC55100STD
-
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
Outdoor Permanent Mounted Load Bank
-
Mosebach Manufacturing Company
Mosebach Pad Mounted Load bank is designed to be permanently mounted next to a generator for dedicated testing. Its unique design allows it to be one of the smallest on the market! This size enclosure will fit 50 kW, 75 kW or 100kW of testing ability. Also available in 300kW and larger load banks.
