Phasing
See Also: Phase, Phase Standards, Phase Meters, Phase Angle, 3 Phase, Sticks, Phasors
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
Multifunctional Meter
CPM-10
-
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
Product
Secondary Master Oscillator
VCH-002
-
The secondary master oscillator (VZG) is designed to operate in a digital communication network as a synchronization equipment of the second level of the hierarchy. Its task is to track in phase one or more clock signals coming through the network from the synchronization equipment of the highest or equivalent level of the hierarchy.
-
Product
Transformer Turns Ratio Meter
TTRM 101
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 101 measures only turns ratio where as TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Quantum Accelerometer
-
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
Product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2220-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Power Transformers
-
Power Transformers are used to convert voltages and isolate signals for functionality and safety. Our broad line of catalog and custom solutions range from mW to 5-10kW and are used in multiple topologies including flyback, forward, push-pull, resonant, LLC and phase shifted full bridges. Typical operating frequencies are between 80-500kHz but solutions can be adapted for greater than 1MHz operation.
-
Product
VectorScope
-
This program plots the left and right components of a stereo signal as vectors in such a way that the direction of arrival of the signal can be estimated. This has application to direction finding, or audio phasing checks. A screen-shot from an earlier version...
-
Product
Dual Band Block Up-Converter
DBUC Series
-
*Connectorized Package *Wide Choice of Frequency Ranges *Dual Band *Integrated Filters *Gain Control *CAN, RS-232, I2C, or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
Relay Protection Test System
RELAYSTAR 1600
-
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
Product
VCOs with Single Output
-
Analog Devices voltage controlled oscillator (VCO) portfolio supports a broad range of applications. Our extensive product line includes multiple devices that offer excellent phase noise performance over temperature, shock, and process due to their monolithic structure. We also offer ultrasmall size, low phase noise, low power consumption, and wide tuning range options to meet multiple design needs.
-
Product
SOP Managemen and Quality Management
arivis BM-Windream
-
BM-windream is the 21 CFR Part 11 compliant data and document management system for the pharmaceutical industry. It is based on the market leading windream document management system from windream GmbH, Bochum. In addition to our industry-specific modules, we have access to a series of tried and tested windream add-on modules from our partner network, e.g. for e-mail archiving, linking to ERP systems, CRM systems, knowledge management or scanning solutions. BM-windream provides a basis for your data and document management that can be validated at relatively low cost (configurable standard software complying with GAMP5) and is easy to use. Users access your documents using a virtual network drive in Windows Explorer, which means that little training is required. BM-windream provides a standardised user interface over the entire life cycle of a file, from creation to deletion. At all phases in this life cycle, a change history (audit trail) is recorded. BM-windream is suitable for handling all kinds of non-managed documents. BM-Flow integrates directly with BM-windream and provides the document management functions required for SOP management,manufacturing instructions etc. All general employees can then still access the documents using the familiar Windows Explorer, while those responsible for creating documents can also use the workflow interface in BM-Flow.
-
-
Product
Venable Stability Analysis Software
-
In 1983, Venable launched the renowned K-Factor Technique, still in use by many instrument manufacturers today. Venable has elevated the original software with its innovative Stability Analysis program. Go straight from measurement to design using Stability Analysis as its dynamic functionality eliminates lengthy manual value calculations and guesswork. Compensation amplifier synthesis capability, or coefficients for digital power supplies, enables user to achieve exact feedback loop bandwidth and phase margin desired on the first try.
-
Product
Network Analyzer
DPNA-6G AXIe
-
The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.
-
Product
40 Amp Intelligent Power Management
IPMDS40
-
- Intelligent Power Management System- 9 - 20 Amp Single Outlets- Automatic Single Phase Load Balancing- Automatic Load Shedding based on priority rating- 40 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
Product
Impedance Analyzer
1260A
-
The model 1260A Impedance/Gain-Phase Analyzer is - without doubt - the most powerful, accurate and flexible Frequency Response Analyzer available today. In daily use by leading researchers wherever measurement integrity and experimental reliability are of paramount importance, the 1260A’s solid reputation is frequently endorsed in published research papers in fields.
-
Product
Portable Three Phase Electric Meter Test Bench
GF302D
-
Beijing GFUVE Electronics Co.,Ltd.
The Portable Three Phase electric Meter test bench is used for grid corporation to cablibrate 3 phase electric meter error. It can test three meters error at one time.
-
Product
10 GHz Signal Source
YIG Series
-
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
Product
Fully Automatic Three Phase kilo Watt hour Meter Test Bench
SY8320
-
Hong Kong Songyang Industrial Ltd.
Suitable design, good figure. The frame for meters and the body frame are fully made by special aluminum alloy. The table board is composed of fireproofing and heat-proof fiber materials. The whole device is in soft color and good figure.
-
Product
Software Engineering Services
-
From the many phases of software engineering, designing, building, testing, implementation, interfacing, and support, enGenius has an expert team and network of highly-vetted partners ready to accommodate projects and programs, both large and small. From the vast list of possible requirements, including web applications, architecture, requirements analysis, network security, and recovery and restoration, enGenius has trusted knowledge management resources for state-side and global projects.
-
Product
Analog Force Gauges
-
Phase II force gauges are designed and engineered to achieve WORLD-CLASS tension/compression measurements. Heavy duty construction allows the force gauges to undergo rough handling in any environment, while providing for extremely sensitive and highly accurate readings. The Phase II force gauges include a direct dual scale reading in both lbf and kgf, eliminating the need for two separate gauges in the shop.
-
Product
Single Phase Portable Energy Meter Test Bench Type KP-P1003-C
-
Bofa Instrument & Equipment Co., Ltd
Single-phase portable test bench, Type KP-P1003-C, is an ideal device to test all kind single-phase energy meters accuracy below 1.0. The equipment can generate single-phase voltage, current and all power factor. The equipment is box structure, light, and easy to carry, it is a very ideal device for energy meter factory to adjust meter at production line, it also can be used as testing equipment in R&D institute.
-
Product
Bus Differential System
B90
-
The B90 Bus Differential System provides fast and secure low impedance bus protection for reconfigurable LV, HV, and EHV busbars. Use one B90 to protect up to 8 feeders and use three or more B90s together in a centralized phase segregated architecture to protect up to 24 feeders.
-
Product
Electro-Optic Modulators
-
Thorlabs’ selection of electro-optic (EO) modulators includes free-space and fiber-coupled LiNbO3 modulators. Free-space amplitude, phase, or resonant modulators can operate at speeds up to 100 MHz. We also offer liquid crystal EO modulators for speeds up to 2.5 kHz. Fiber-coupled intensity, phase, or IQ modulators for speeds up to 40 GHz can be driven by our EO modulator drivers. A modulator bias controller is also available for use with fiber-coupled intensity modulators.
-
Product
Relay And Protection Testing
-
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
Product
100MHz DDS Signal Generator
408A
-
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
Product
2.5G DPSK Demodulator
-
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Product
Multifunction Instrument
COMBI521EV
-
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
