-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
RF Ports Alignment Software
-
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
CMX RF Port Extender
CMX-Z25
-
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
Product
Personal RF Detection Meters, High Frequency
-
Personal RF Detection Meters from Sensory Perspective Ltd
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, MCX
40-835A-101
Multiplexer Module
The 40-835A-101 (PXI) and 42-835A-101 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
-
Product
AC Load Bank (Resistive/Reactive)
K-1000 Resistive/Reactive
-
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
UltraCMOS SP12T RF Switch
PE42512
-
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
Product
Dual 16 to 1 50 600MHz PXI RF Multiplexer
40-764-002
Multiplexer Module
This dual 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Quad 8 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-763-004
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
802.11a,b,g Dual RF Shielded Test Enclosure
JRE 0814-2R-A
-
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
-
Product
Electronical Load Board 3U CompactPCI (air cooled)
045-097
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of feeder
-
Product
PXIe-2790, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module
782576-01
Multiplexer Module
PXIe, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module—The PXIe‑2790 can either switch or combine RF signals for multi-DUT cellular and wireless connectivity production test. It features high-performance solid-state relays that offer unique benefits such as an unlimited mechanical lifetime and fast switching time, as well as front-mounted SMA connectors that provide easy connection to your RF devices.
-
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, 3GHz, 75Ω, SMB
42-834A-001
Multiplexer Module
The 40-834A-001 (PXI) and 42-834A-001 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Liquid-Cooled Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
EMAX's liquid-cooled load banks are the best choice for industries and applications with their high efficiency, compact size, quiet operation and precise load testing.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 3GHz, 50Ω, MCX
40-873A-101
Multiplexer Module
The 40-873A-101 (PXI) and 42-873A-101 (PXIe) are 4 to 1 RF MUX with 1 bank in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
Anti-Islanding Load Banks
AI-Series
-
AI-series anti-islanding load banks containing purely resistive, inductive, or capacitive load, have segmented combination control of power input, and can simulate a variety kinds of power loads to meet the grid-connected inverter full load test requirements.
-
Product
PXI/PXIe RF Matrix, 32x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-021-L
Matrix Switch Module
The 40-724-021-L (PXI) and 42-724-021-L (PXIe) are 32x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
PXIe Down Converter: 4 Channels, 2-16 GHz RF, 0.01-2.4 GHz IF
M5201A
Downconverter
Single-slot PXIe low-IF downconverter module with a 2 to 16 GHz RF input frequency range and 0.01 to 2.4 GHz IF range
-
Product
Small Compressive Load Cell
CCSM-3.0
-
DLM’s range of Small Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
RF R-PHY Video Engines
-
ATX’s RF R-PHY video engines provide a mux pass-through function that enables cable operators to maintain existing video encryption functionality on in-service edge QAMs, alleviating the need to migrate encryption functionality to the CCAP video core during early stages of DAA transition. ATX RF R-PHY video engines also relieve MSOs of undertaking back-office system integration to reconfigure and manage muxes and broadcast lineups in CCAP video cores. For MSOs considering an accelerated transition to IPTV, the ATX RF R-PHY Video Engine provides a low-cost and low-complexity alternative to implementing a CCAP video core.
-
Product
Inductive Load Banks
L-Series
-
L-series inductive load banks are devices which contain inductive loads, apply the load to an electrical power source and dissipate the reactive power of the electrical source. L-series load banks are designed for portable and fixed applications. Hilkar brand L-series load banks have robust design and are specifically designed for corrosive environments. Load banks can be controlled via local, remote, wireless remote or automatic control systems.
-
Product
Programmable Electronic Load
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
Product
50 Ohm SMB to SMA Adaptor Assembly
40-978-521-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
