-
Product
512 Channel Systems
Spider-80X/Spider-80Xi
-
The Spider-80X is designed for applications in three fields: dynamic data acquisition, vibration control, and machine monitoring. Each front-end features eight analog input channels and two channels that may be software selected as analog outputs for vibration control or tachometer inputs for the analysis of rotating machinery.
-
Product
Combustion Efficiency Analyzers
-
Test Products International, Inc.
Determine combustion efficiency, CO2, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.
-
Product
Traceroute and Network Diagnostic Tool
VisualRoute
-
Traceroute. Key diagnostic data such as packet loss and response times are displayed in an easy to understand traceroute table. Hop by hop analysis makes it easy to pin point problem areas. Reverse trace (remote agents). One of the most powerful features of VisualRoute (SupportPro edition) is the ability to create remote agents. Remote agents allow the user to perform a reverse trace between two locations without actually being present in either location. Reverse DNS. Use VisualRoute to perform a reverse DNS lookup. This allows the user to uncover the IP address behind a domain name, such as www.visualware.com.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PCI Compliance Testing
-
The Payment Card Industry Data Security Standard (PCI Standard) defines merchant requirements for securing cardholder information. This worldwide standard for consumer data protection across the payment industry was developed to counteract the rising number of incidents of stolen cardholder account data.?
-
Product
Rating Analyzer
-
Actus Rating Analyzer provides efficient rating and competitive analysis tools. It provides a clear graphical view of all rating information, yours and competition, along with the actual broadcast media. The clear rating and demographic data display allows you to get an easy at-a-glance information from all numbers and charts received from the rating companies. The end result is a far more accurate analysis of the content, which in turn allows research teams to give much more informative and accurate recommendations, leading to better program planning, ad placement, and even more viewers watching the shows all significantly increasing revenues.
-
Product
PXI/PXIe Very High Density Multiplexer, 99-Channel, 2-Pole
42-675B-002-99/2
Multiplexer Module
The 40-675B-002-99/2 (PXI) and the 42-675B-002-99/2 (PXIe) are 99-channel, 2-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Product
On-site Support
-
Aerodyn provide a complete field test service, offering on-site support at demanding and often remote test sites. We instrument test articles, route lead wires, configure data acquisition systems, record data, reduce data, and write test reports. We conduct tests on aircraft, in test cells, at power stations, aboard ships, and at manufacturing facilities.
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
2U 20" Short-Depth Edge Server
HPC-6240+ASMB-622V3
-
2U 20" short-depth edge server with a 5th/4th Gen Intel® Xeon® CPU, 4TB DDR5, and 8 PCIe Gen5 slots. Built for high-density AI and edge data centers.
-
Product
6U VPX Portable Platform
VP4P201
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP4P201 is a 6U VPX portable platform compliant with VITA46.0 specification. With the air cooling design and VPX modular design on the chassis, VP4P201 has excellent heat dissipation performance. VP4P201 is manufactured with high-impact Al alloy structure, and its surface is processed by hard anodic oxidation.VP4P201 is equipped with a 6U 5-slot Single-Star VPX backplane that has 4 payload slots and 1 switch slot. The connector on VP4P201 can realize data exchange between data planes and control planes of 4 payload boards. Besides, there is a 460W ATX AC/DC Power installed in the chassis.VP4P201 is highly applicable in measurement and testing. As a standard package, VP4P201 can also work as a traditional CPCI or PXI chassis by the replacement of the backplane.
-
Product
Communication Devices
-
Communication devices store and retrieve data acquired by data acquisition systems. These devices facilitate the accessibility, analysis, sharing, and reporting of data. Our available communication devices include both on-site and telemetry peripherals, which can be used in the same application for maximum flexibility, convenience, and reliability.
-
Product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4I.4421-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Drive Recorders & Monitor
ES700
-
The ES700 family of products is focused on the in-vehicle tasks of data collection and monitoring. There are currently three products in this product family: The ES710 Drive Recorder, the ES715 Drive Recorder and the ES780 Heads Up Display.
-
Product
Multi-Functional Dynamic System Monitor
PFMonitor
-
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
Product
K-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-K001
Thermocouple Contact (ITA)
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Thermocouple Data Logger
TGU-4550
-
The Tinytag Ultra 2 Thermocouple data logger uses a thermocouple sensor for the cost-effective monitoring of temperature in a wide variety of applications.
-
Product
Event Based Image Sensors
EVS
-
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
Product
Fiber Optics Bridge Card
DP8000
-
Guzik DP8000 Fiber Optics to PCIe® bridge / FPGA Accelerator Card, enables evolving markets such as High-speed Data-acquisition, High Performance Computing to take advantage of the latest Optics and DDR4 technology. The card provides up-to 24 bi-directional optical links with total user data bandwidth greater than 40 GB/s (320 Gbps) through the Samtec FireFly™ protocol-agnostic embedded optical engines.
-
Product
STAMINA High-Speed Multi-Camera Recording
-
Stamina combines advanced hardware with easy to use software to offer a complete multi-camera recording solution for your imaging challenges. With the complete imaging system it becomes possible to record, view and combine up to 9 cameras in one setup. Our software is compatible with a wide range of cameras, providing the option to integrate your own cameras into the imaging setup easily.With Stamina, all recordings can be synchronised and all image data is directly streamed to the solid storage, enabling longterm streaming. With the external Application Programming Interface (API), Stamina can be further customised and integrated in your existing setup. Through the API, you have access to device settings, recording parameters and image data.Stamina is a completely customizable multi-camera recording and imaging solution. Our experienced sales engineers will advise you on the right system for your application.
-
Product
Flip-Flop Electronics
-
Analog Devices supplies a range of D type and T type flip flop products. Members of this portfolio can support data transmission rates up to 43 Gbps and clock frequencies as high as 43 GHz. All of our flip flop products are RoHS compliant and available in 3 × 3 or 4 × 4 SMT packages.
-
Product
PXI-5152, 300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope
779772-03
Oscilloscope
300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope—The PXI‑5152 high-speed PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations. The PXI‑5152 also features PXI synchronization and data streaming capabilities.
-
Product
Software
Gate Oxide Integrity Option
-
Materials Development Corporation
Oxide integrity of MOS devices can be evaluated by various techniques such as Time Dependent DielectricBreakdown, Charge to Breakdown, or ramped voltage. When used with a prober, map distribution of breakdown fields. Output the data using histograms, cumulativefailure, or Weibull plots.
-
Product
Bustec VISA Library And Tools
ProDAQ 8200
-
The Virtual Instrument Software Architecture (VISA) is a standard for configuring, programming, and debugging data acquisition and test systems using hardware interfaces like Ethernet, USB, PCI Express, GPIB, IEEE1394 or even RS232. The VISA library provides a standardized application programming interface between the hardware and application programming environments like LabVIEW, LabWindows, Visual Basic etc.
-
Product
IR Thermometer
DIT-500
-
Temperature meters operating in the infrared are used to determine the temperature of the surface of the item. The optical system of the device detects the emitted, bounced and sent energy, which is collected and concentrated on the detector. Electronic system translates optical data into temperature value. In order to increase accuracy the laser pointer is built-in the device.
-
Product
Talon RTX Small Form Factor Offload System
Talon RTS 2580
-
- The Talon® QuickPac® drive can be removed from a Talon RTX - SFF recorder and inserted in this offload system- Allows the Talon recorder to remain deployed in the field- Data stored on the QuickPac drive can be accessed and offloaded for analysis- Designed for Talon models RTX 2586, 2589, 2590, 2596, and 2684- Can offload data to removable SATA drives, DVD, Ethernet and USB ports- 4U 17-inch PC server chassis, 21 inches deep- Windows® workstation- Intel® processor- 8 GB DDR SDRAMSystemFlow® Software
-
Product
Semi-Automatic Probe Sheet Resistance/Resistivity Measurement
CRESBOX
-
• Multi-points measurement and Mapping display- 2-D map / 3-D map graphic display- Multipoint pattern measurement is programmed (maximum 1225 points) and random pattern is programmable by operator.• Film thickness conversion function from sheet resistance• Measurement data base link with Excel via CSV format file• Software language can be switched in English /Japanese by operator
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
Motherboard
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
Product
The PC Link Software For CAN/LIN Data
LE-PC87
-
This PC link software “LE-PC87” captures CAN/LIN data into PC measured by the CAN/ LIN optional expansion kit for LE-8200A/LE-8200.
