Lock-in Amplifiers
measure a signal's amplitude and phase in noisy environments. Measure hi-res clean signals.
See Also: Optical Choppers
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Composite 2×12 Video Distribution Amplifier 12VDC
VDA212RM-12
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
-
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
RF Amplifier
SA822
-
Hangzhou Softel Optic Co., Ltd.
SA822 860 MHz outdoor distribution amplifiers are mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
Product
Broadband RF/Microwave Power Amplifier
-
R&K wideband power amplifiers support a wide range of applications with their broadband characteristic.
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Ultra-small / Cable Type]
PM-25
-
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-25 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1mm thereby reducing the possibility of sensing objects colliding.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
Medium-Power, Broadband Amplifiers
-
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
-
Product
Distributed Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support distributed amplifiers that provide a simple and easy solution for a wide variety of commercial and aerospace & defense applications. MACOM’s distributed amplifier family cover frequencies from DC to 80 GHz and are offered in both bare die and air cavity packages. These devices offer an excellent combination of broadband performance and ease of use for a variety of high-performance applications.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
RF Amplifier
SA1001H
-
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
-
Product
Amplifiers
-
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
Product
SX Range Broadband Power Amplifiers 0.8 GHZ - 6 GHZ
SX Series
-
Solid-state amplifier / Class A. Broadband (Dual-band): 0.8 GHz - 6 GHz. Typical output power:
-
Product
4 Channel Variable Gain Fast Amplifier
V974
-
The Mod. V974 is a 4 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a voltage gain adjustable from 1 to 10 in x1 steps. Channels are non-inverting and bipolar: they amplify both positive and negative signals.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
High voltage amplifiers (to ±500V)
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
PM-45
-
Panasonic Industrial Devices Sales Company of America
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Compact / Cable Type]
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
Hybrid Amplifiers
LNA
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components that include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
Low Noise Amplifier
DLNA8-40-50-2582
-
Low Noise Amplifier, Frequency 40~50GHz, Gain 38dB, Noise figure 3dB, P-1dB 13dBm, 1.85mm-Female Removable
