Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
Product
Electric Vehicle AC Charging Compatibility ATS
8000
-
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements
-
Product
In-Line Full Automatic Testing System
ALMAX
-
Automated press unit with board loading belt.ALMAX can become automated in-line type in-circuit tester in case our ICT is integrated. And it also can become automated in-line function tester as well.PLC is not used in order to reduce cost as a PC control mechanical part.Press unit is 4 shaft structures which reduce unbalanced load and contact fail of probe pins.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
Power Electronics Test Solutions
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Microhardness Tester
MT91 Series
-
Newage Testing Instruments, Inc.
The Newage MT91 System is an automatic microhardness testing system that uses the Rockwell method for the hardness result. Hardness is measured based on the depth of penetration rather than using an optical system to determine hardness based on the impression diameter.
-
Product
Battery Pack ATS
8700
-
Chroma transfers its successful experience in 8000 ATS which is quite well-known in the power electronics industry to the battery application field by developing the Test Items specifically for the battery industry. It can perform automatic tests on the Battery Management System (BMS), semi products and finished products tests on the production line as well as provide long term maintenance and service to the battery module. 8000 (8700) ATS has flexible hardware architecture that can select a variety of hardware devices, such as DC Power Supply, Electronic Load, LCR Meter and 6 1/2 digits Meter, etc. to comply with different automatic testing requirements for various applications. In addition new hardware and test items can be expanded to meet the demands for inspecting the highly customized battery products with diversified tests. The capabilities supported are:
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
-
Product
In-line vacuum test systems
-
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
Product
Three-phase Fully Automatic Test System
TS41
-
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
Product
The Lorlin© Impact Series
-
Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability. The system tests most all discrete semiconductors with reliable, accurate, and repeatable results.
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
Test System
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Automated Tuners / Impedance Tuners / Load Pull Tuners
-
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
Product
Integrated Development Environment for the Creation and Execution of IEEE1641 Test Programs
SigBase
-
SigBase is an Integrated Development Environment for the creation and execution of IEEE 1641 test programs. It supports the development of tests using flow-charting techniques and the graphical design of signals using newWaveX. It includes fully integrated compilation and signal path allocation software that determines the appropriate instrument and switch path for each signal and test. The run-time system, which is also available as a separate product for use on multiple test stations, controls the operation of the ATS and can provide test results in ATML format.
-
Product
High-Power LXI Matrix Modules
-
Pickering's high-power LXI matrices are a single pole module available in a variety of configurations and are suitable for power signal routing in large automatic test equipment (ATE) systems. They are available with a selection of X and Y sizes as well as partially populated configurations.
-
Product
Adapter/Charger ATS
8020
-
Chroma 8020 has standard test items specially customized and optimized for the features of Adapter and Charger that provides excellent test performance to meet the requirements of mass production. Meanwhile, the software equipped is very friendly and easy to operate that is suitable for production line use.
-
Product
Electric Vehicle Supply Equipment ATS (EVSE ATS)
-
It is a customized system based on Chroma 8000 ATS specializing inverification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.
-
Product
Automated Relay Test System
Relay Master
-
Relay Master is an automatic relay test system capable of testing from one to 64 relays simultaneously without having to remove them from the rack. System automation improves efficiency and reduces track time requirements. The PC-based system stores test parameters and results in a database for ease of reliability and trending analysis.
-
Product
ATE Integration
-
Want to improve the overall test coverage of your assembled boards? It’s easy. Simply combine or integrate your JTAG Technologies boundary-scan tools with your existing automatic test equipment (ATE). We work with any vendor of in-circuit testers (ICT), flying probes (FPT) or functional testers (FT).We offer solutions for most of the available automatic test equipment systems, in addition we can support you with customized integrations for your existing automatic test equipment (ATE).
-
Product
Sensors
-
Advanced Thermal Solutions, Inc.
ATS designs a range of sensors for more accurate measurement of air and surface temperatures and air velocities. The different models allow data to be obtained in many conditions, including tight spaces and narrow planes. ATS sensors work exclusively with our ATVS family of hot wire anemometer systems.
-
Product
Industry Standard in Noise Measurement
PN9000
-
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range(2 MHz to 140 GHz). Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a compact instrument.
-
Product
Fully Automatic Tensile Testing System
-
This is a fully automatic tensile testing system for metals. The system is fully automated from supply of specimens, measurement of specimens, tensile testing, recovery of specimens, and data processing, and is capable of continuous nighttime testing.
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
HCU/DC-DC Converter ATS
8900
DC Converter
Low power testSleep mode current testInput overvoltage limit testLine regulation testEfficiency testLoad regulation testOutput ripple voltage testDC-DC load testOvercurrent testPower doen and isolation test
-
Product
Automatic Test System
Star-Rec
-
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
Product
4/8 Channel Optimal Multiport Power Meter
UC8728
-
UC INSTRUMENTS UC8728 4/8 CHANNEL OPTICAL MULITIPORT POWER METER are PC control multiport passive components power meter test system and offer superior performance for the test of multichannel DWDM, WSS, ROADM, AWG & PLC components and modules, optical amplifiers, DWDM system and other general purpose of multiport fiber optical test and measurement applications. The system can be integrated with tunable laser source, optical attenuator & PDL controller provides a high performance passive components and modules automatic test system platform.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
Electric Insulation Oil Automatic Measurement System
DAC-5016
-
DAC-5016 is an automatic test system of insulation oils according to JIS C-2101.The system automatically enables changing over samples (liquid cells) up to max 8 pieces and testing the dielectric loss tangents and the volume resistivities.In automatic mode, the dielectric loss tangents and the volume resistivities are automatically measured, and then the results are printed out with the built-in printer. And the relative permittivities and the volume resistivities calculated are also printed out. Therefore the test time is greatly saved compared to the conventional test methods.
-
Product
Multiport Coaxial Switch, DC to 20 GHz, SP6T
87106B
-
The Keysight 87106B multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87106B terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
Product
LXI High-Density Matrix
-
Our LXI High-Density Modules are single and double pole matrices available in a wide range of configurations including versions with the added flexibility of dual analog bus. These high-density matrices are ideal for signal routing in large automatic test equipment (ATE) systems and are suitable for applications where a simple start-up process is required and for applications requiring control over large distances.
