Breakout Boxes
reroute signal paths to facilitate contact accessability.
See Also: Boxes, Breakouts, Decade Box, Anechoic Boxes, Black Box, Hot Box, White Box, Shielded Box, RF Box, Programmable Resistance Box
-
Product
SparkFun I2S Audio Breakout
MAX98357A
-
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The I2S Audio Breakout converts the digital audio signals using the I2S standard to an analog signal and amplifies the signal using a class D amplifier which can deliver up to 3.2W of power into a 4Ω load. The board can be configured to output only the left channel audio, right channel, or both.
-
Product
SparkFun Cryptographic Co-Processor Breakout
ATECC608A (Qwiic)
-
The SparkFun ATECC608A Cryptographic Co-processor Breakout allows you to add strong security to your IoT node, edge device, or embedded system. This includes asymmetric authentication, symmetric AES-128 encryption/decryption, and much more. As stated above, the ATECC608A has limited Arduino support and the complete datasheet is under NDA with Microchip.
-
Product
SparkFun USB MicroB Plug Breakout
-
We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all five pins with a vertical microUSB connector for your prototyping needs.
-
Product
SparkFun Level Shifting MicroSD Breakout
-
The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD library’s top speed on a 5V system. With this small breakout board, that is not much bigger than your fingernail, adding mass storage to your project will never be easier.
-
Product
RF Shielded Box
TS7124
-
R&S®TS7124 RF shielded boxes enable reliable and reproducible measurements in shielded test environments. The R&S®TS7124 shielded box provides high shielding effectiveness, a good antenna coupling factor and a rugged mechanical design for reproducible results. RF test boxes have been designed not only for product designers or product optimization but also for production lines of wireless devices under test. The soft close feature makes the shielded box safer to operate.
-
Product
VB Build-A-Box
-
The VB Series, Build a Box provides a solution for any combinations of signal transport over fiber. With the VB-10 (10 card slots), VB- 6 (6 card slots), VB-4 (4 card slots), a unit can be created to your specification by populating the case with any configuration of VB-Cards. Each card’s I/O can be sent or received over its own disparate fiber, or all signals in the box can be multiplexed onto just one fiber. Inherently portable, each unit is ready for field applications or can be rack-mounted with optional Rack Mount kits.
-
Product
SparkFun Digital Temperature Sensor Breakout
TMP102
-
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn't require much setup.
-
Product
50-Pin D-Type Breakout Female DIN mount
40-967-050-F
-
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
Product
RF Shielded Box
LTL B2001
-
LTL B2001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B2001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Compact Box PCs And Digital Signage Players
-
ADLINK industrial box PCs and digital signage players are designed to meet the diverse needs of industries such as retail, transportation, and manufacturing. These compact edge computing solutions ensure reliable performance for real-time data processing and seamless vivid content delivery. Featuring industrial-grade durability, flexible I/O configurations, and scalable options, the EMP Series helps businesses optimize operations, enhance customer engagement, and drive digital transformation in demanding environments.
-
Product
SparkFun Serial Basic Breakout
CH340G
-
The SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. It works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340G IC to quickly and easily convert serial signals to USB. It’s a great lower-cost alternative to the extremely popular FTDI Basic.
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
SparkFun Qwiic EEPROM Breakout
512Kbit
-
The SparkFun Qwiic EEPROM Breakout is a simple and cost effective option to add some extra storage space to any project. With 512 kilo-bits (or 64 kilo-bytes) of storage, this product is great for any microcontroller that doesn't have any EEPROM storage space, like the SAMD21. You can use the Qwiic EEPROM for storing data like GPS waypoints and other user settings that need to be maintained between sketch uploads. The SparkFun Qwiic EEPROM has three address jumpers, allowing for up to eight EEPROMs on one bus. All communication is enacted exclusively via I2C, utilizing our handy Qwiic system (as the name implies). However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
SparkFun GPS Breakout
ZOE-M8Q (Qwiic)
-
The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
DISCRETE TMTC INTERFACE BOX
-
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
-
Product
SparkFun Gas Sensor Breakout
-
This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on every MQ gas sensor product. This is an extremely handy and economical board to have around when detecting multiple types of gases.
-
Product
LTE/WiFi Test Box - Adjustable Bandwidth Tunable (700MHz - 6000MHz)
-
K&L has developed and is now shipping an LTE/WiFi testing solution digitally-controlled filtering system that can tune a bandpass filter anywhere in the 700 MHz to 6000 MHz range with continuously adjustable bandwidth. View latest video to see in operation.
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
SparkFun Proximity Sensor Breakout
20cm, VCNL4040 (Qwiic)
-
The SparkFun Proximity Sensor Breakout is a simple IR presence and ambient light sensor utilizing the VCNL4040. This type of sensor is often seen in automatic towel and soap dispensers or automatic faucets. With the ability to detect objects qualitatively up to 20cm away, you will be able to detect if something is there and if it is closer or further away since the last reading. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
-
Product
50 Pin IDC Connector Breakouts
-
The connector breakouts below are suitable to use with Pickering cabling products that utilize a 50-pin IDC connector.
-
Product
34-Pin IDC Breakout, DIN Rail Mount, Screw Terminal
40-967-534-M
-
This accessory is designed to be used for terminating a 34-Pin (0.050" pitch) Ribbon Cable Connector and includes a strain relief. The accessory is suitable for mounting on DIN rails.
-
Product
Shield Boxes
-
Concentric Technology Solutions, Inc.
CTS can provide a customized integrated RF Shield Box or RF Enclosure Test Solution for manual or automatic testing at an off-the-shelf solution price. Many companies make RF Shield boxes, RF Enclosures or DUT fixtures, but only CTS bridges the gap by providing a complete integrated RF Shield Box or RF Enclosure testing solution for providing the RF shielding needed for repeatability within your budget and schedule.
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
Product
Wiring Boxes
-
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
Product
SparkFun 2D Barcode Scanner Breakout
-
The SparkFun 2D Barcode Scanner Breakout is a nifty little breakout board featuring the DE2120 barcode scanner module from DYScan. The DE2120 reads 20 different barcode symbologies (both 1D and 2D) using a camera coupled with on-board image processing to identify and decode everything from UPC codes to QR codes. The module also features two LEDs: one for illumination and one to project the red line that you're used to seeing from laser-based scanners.
-
Product
Box Compression Tester
-
These advanced Box Compression Testers are PC-controlled systems primarily used in the packaging industry for determination of the compression strength of cartons, containers, cardboard boxes, etc.
-
Product
ONE BOX
-
Both the Z and X handheld analyzers run on the same software platform, operating system, have the same user interface, same battery, and same charger making training and operation a breeze. Get them both when you purchase the ONEBOX package.
