Optical Choppers
Intercept current or beams of radiation on a periodic basis.
See Also: Lock-in Amplifiers
-
Product
Fiber Optic Transmitter/Receiver & Repeater Board
-
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
Product
Electrical and Optical & Bit-Error-Rate Testers (BERTs)
OptoBERT™
-
The OptoBERT family of BERTs offers the best value in the industry for bit-error-ratio testing of optical and electrical components, subsystems and systems. OptoBERT family of products covers data rates from 100 Mb/s to 28.05 Gb/s.
-
-
Product
LXI Optical Switching - 16:1 Multiplexer Plugin Module
65-281-314
-
The 65-281-314 16:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, ST Connectors, With Interlock
42-850A-514-M50-HI
-
The 40/42-850A-514-M50-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-850A-214
-
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-432
-
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-M50-HI
-
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
40-855A-212-M
-
The 40/42-855A-212-M is a PXI/PXIe 2-channel multiplexer with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Optical and Contact Tachometers
-
PeakTech Prüf- und Messtechnik GmbH
Provides a fast and accurate measurement of the speed and surface speed of rotating objects. Through the contactless or with the measuring adapter for measurements by direct contact to the object to be measured, various speeds can be determined and recorded.
-
Product
Standard In-door Forward Optical Receiver
ONR-8636
-
Hangzhou Huatai Optic Tech. Co., Ltd.
ONR-8636 with standard configuration is a type of high index and universal in-door forward optical receiver. It adopts Philip optical receiving module. End-grade adopts power-doubling module. Optical connectors and RF connector can be installed at the front panel or back panel.
-
Product
Variable Gain Optical Amplifier Module
VGA4500-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4500-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
Fiber Optic Type Chemical Solution Concentration Monitor
CS-100F1 Series
-
The CS-100F1 Series is equipped with fiber optics cable based on the CS-100 Series. It offers real-time, in-line measurements by directly integrating the sample cell into the cleaning system piping and by using a fiber optic cable for light signal transmission. A single concentration monitor can take up to four measurements and monitoring of multiple chemical solutions in a single-bath or single-wafer cleaning system is also possible.
-
Product
Fiber Optical Monitoring Alarm System
FOMA
-
FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
Product
Optical Assemblies
-
Our team works closely with your design team to develop a custom, long-term production solution that fits your specific program. Our manufacturing niche is in low- and mid-volumes (10 to 1,000 units) for assemblies with demanding or non-standard optical performance requirements. Along with Promet’s rigorous QC protocols, our in-house testing labs and engineering support ensure a well-controlled process and predictable results.
-
Product
Optical Hand Clinometer
NECLI
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*Quick determination of slope and height of objects*Robust design*Vertical circle oscillating in precision ball bearings with four different graduations (360°, 400gon, %, reduction scale)*Simultaneous reading of two out of four scales direct in scope*Quick reading because of liquid damping*Reading 0,1°*Made in Germany
-
Product
47~2600MHz Digital TV & Satellite TV PIN Optical Receiver
HRS-26D/P
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26D/P optical receiver, adopting high-sensitivity PIN detector, receiving sensitivity is -22dBm, typical value -13dBm. It can receive analogue and digital signal with the frequency of 47~2600MHz on a single fiber, and compatible with any FTTx PON to achieve triple-network combination between Analog TV(<10CH), Digital TV (DVB-C, DVB-T), Satellite TV (DVB-S) and Internet & FTTH.
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324-DSP
-
The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.
-
Product
Fiber Optic Sensors
-
Leuze electronic GmbH + Co. KG
Plastic fiber optics are suitable for universal applications with low space requirements for object detection. Glass fiber optics are used in demanding environmental conditions with high temperatures and are resistant to chemicals. For radiation through foils or applications with high light power, they offer further advantages through the especially low damping. The flexible fiber optics with various head shapes can be integrated in nearly any system design. The detection range is dependent on the fiber optics and amplifiers used. Fiber optics can be used with the throughbeam principle or with scanning function. As a fiber array with multiple light beams, they can be used to detect especially small objects.
-
Product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
-
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-014-M62.5-HI
-
The 40/42-850A-014-M62.5-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Sample Pretreatment For Optical Emission Spectrometry
-
Samples are taken from molten metal, thin sheet, semi-complete or complete products. When sampling molten metal with a ladle, small quantities of molten metal are poured into a casting mold. Unnecessary parts of the sample are removed using a grinder or a cutter. As particles from a grinder may contaminate the surface of the sample, a lathe or milling machine is used (not a grinder) to cut soft samples such as white metal. If trace elements are not being investigated, a grinder or belt sander can be used. However, to minimize contamination, the grinding wheel or belt should be changed for each sample. Samples excised from semi-complete or complete products must be at least 12 mm in diameter. Small rod-shaped samples can be analyzed using special equipment.
-
Product
Built-In Modular Type Optical Power Meter
MPM-200A, MPM-200M
-
MPM-200A•Very small and lightweight•Univeral 2.5mm adapter to accept FC, SC or ST.•Built-in modular type.•RS232 inferface to System or PC/Laptop.•Automatic measurement of wavelength and optical power.•CWDM-PON wavelength and Power meter module.•FTTx/PON wavelength and Power meter module.MPM-200M•Very small and lightweight•Univeral 2.5mm adapter to accept FC, SC or ST.•Built-in modular type.•RS232 inferface to System or PC/Laptop.•General optical power meter.•Dedicated for all single-mode and multi-mode applications.•CWDM-PON wavelength and Power meter module.•FTTx/PON wavelength and Power meter module.
-
Product
Optical Power Meter
PM-202B
-
The all-in-one PM Series Optical Power Meter are designed for use with an Optical Source for performing optical loss measurements on fiber optic cables. The PM-202 series are designed for affordable budgest, but meet the basic demands for real world testing. With a smaller size and weight, it’s easy to take these units into any enviroment.
-
Product
Optical Receiver
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Return path optional. Frequency splitting according to customer’s need.* 2 RF outputs, level ≥104dBμV when optical input @ -1dBm.* Output level tunable through buttons on front panel.* RF Test Point on front panel.* High quality switch power supply.
-
Product
Fiber Optic Light Sources
-
Fiber optic light sources are a necessity for performing optical fiber network testing to measure the optical fiberal loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the optical fiber power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the optical fiber power meters, they act as an economic and efficient solution for the optical fiber network works.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode
40-852A-218
-
The 40/42-852A-218 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors
42-850A-114-M50
-
The 40/42-850A-114-M50 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Handheld Fiber Optic Light Source
-
Anfkom International Co.,Limited
3109 optical light source can provide 1 to 4 output wavelengths to meet specific requirements,including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber,as well as other wavelengths according to customer needs.Together with the 3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
