Compressor
Reduce volume by pressing together.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Current To Pressure Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Current to Pressure Trainer. This setup comprises of a I to P converter fitted on a base. Two pressure gauges are fitted one at the input side and the other at the output of the I to P converter. A current source with digital display is provided to excite the I to P converter. A constant air supply should be provided to the system at 20 PsI Pressure from a standard compressor.
-
Product
Temperature Chamber
S/SM-Series
-
Thermotron's S/SM-Series temperature-only and temperature-humidity environmental test chambers deliver quality, accuracy, and reliability. The self-contained refrigeration system and diverse compressor size options provide moderate temperature change rates while allowing the climatic chamber to consume less power than comparable test chambers. From prototyping and durability testing to component screening, the S/SM-Series is a cost-effective testing solution.
-
Product
Automotive Audio Processors
-
ST’s wide portfolio of analog and digital signal processors covers the full range of features and channel configurations for the car-audio application spectrum, from low-end solutions to high-end premium audio systems. More than 40 analog signal processors offer a large choice for the number of inputs, number of output channels, and baseband audio functions, including EQ, dynamic compressors, subsonic filters, and more. Alternatively, a fully digital solution with embedded 20-bit audio ADCs and DACs is based on a proprietary 24-bit DSP specifically crafted for audio applications.
-
Product
Compressor-Cooled Incubator
ICP
-
Our ICP compressor-cooled incubator offers great results whenever a rapid and precise changeover between heating and cooling phases in ramp operation is required. Due to the finely tuned control technology, temperatures exactly reach the setpoint values without the need for energy-intensive bursts of power.
-
Product
PMS Leak Test System
-
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
Product
Automobile Engine-related Measuring Machines
-
Automatic Measuring Systems > Automobile engine-related measuring machine. Crankshaft, Camshaft, Cylinder block, Piston, Compressor wheel and Cylinder head.
-
Product
Insect Rearing Chambers
-
Chamber uses thermoelectric assembly for heating and cooling. This type of cooling/heating system completely eliminates need for conventional refrigeration system and failures due to mechanical components such as compressors thereby drastically increasing the life expectancy of each chamber.
-
Product
Leak Detection Oil
-
The faster, safer and easier way to locate even tiny leaks in industrial air conditioning and refrigeration systems. Lumirati® bottled dyes can be poured directly into any AC&R system. The dye can remain safely in the system to confirm repairs and perform future preventive maintenance checks. Lumirati® Leak Detection Oil is the only dye that gives you all these benefits:- Universal dye that is compatible with all refrigerants and lubricants- OEM-approved by major compressor, refrigerant, lubricant and AC&R equipment manufacturers- Co-solvent free so dye will not impair lubricant properties, which could lead to excessive wear or damage to the system components
-
Product
Environmental Stress Screening (ESS) Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Integral structure, the inner wall special process rolling molding, the whole using TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism.- The use of Chinese+English color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box special software, with automatic, intelligent, human control and other characteristics.- Control mode: constant operation mode, program operation mode.- Patented "Cold and heat balance technology”, low temperature constant temperature season can be more than 30%.- Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions.- Configure RJ45 communication interface, remote control system (open data transmission protocol support Modbus/OPC).- Surface electrostatic powder spraying; Box color "TESTEQ White ", controller panel color "TESTEQ Blue ".- TESTEQ patent cold well adsorption anti-condensation function (optional).
-
Product
Pressure Switches
-
Whitman controls offers the most diverse selection of pressure switches in the industry. Our diverse line of switches are used across a wide range of applications including blowers, generator sets, off-road vehicles, compressors, wafer ovens, process equipment, flow control devices, pumps, wastewater, heating and cooling systems, and numerous other applications across industries.
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
Product
Small/Medium Capacity Torque Detector
SS series
-
The SS series torque detector suits to wide variety of torque measurement application, including performance test of motors, pumps, compressors, blowers, turbines and gears. High rigidity results from the unitized cast-casing structure and SS series torque detector can be handled easily as being free from parts replacement on treatment of maintenance, comparing to other type of torque detector such as strain gauges, with non contact signal detection on the detector. 13 models in the series can be provided and chosen among them according to requirement in torque capacity.
-
Product
Pro Laser Tachometer
332
-
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
Product
Rapid Temperature Change Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
The Wewon’s rapid temperature change test chamber is equipped with two 1.5 kW French Tecumseh compressors, Cooling capacity temperature change rate can be 3℃ / min. The machine can carry out on-line product quality inspection task according to the specified temperature change rate. The volume and wind speed will be adjusted automatically, This makes the temperature in the test area is evenly distributed. Through an electronic expansion valve, The surface temperature difference of the tested product is suppressed, and the linear control precision is realized.https://www.wewontech.com/rapid-temperature-change-test-chamber/
-
Product
Walk-In Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Energy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions. The technology is based on Danish Danfoss' ETS series of electronic expansion valves, which can be used to smoothly adjust the cooling capacity for different cooling capacity requirements, that is, to achieve the compressor cooling capacity adjustment when different cooling rate requirements are met.
-
Product
Testing of Compressors and Compressors
-
Automatic production test bench for semi-hermetic refrigeration compressors on 2 parallel assembly lines with 3 test stations each and central database.
-
Product
Motor Capacitor
CBB65
-
High safe required Motor starting and running,energy storage,smoothing etc. Air conditioner,compressor etc.
-
Product
Sequence / Rotation Indicators
-
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
Product
Impact Specimen Preparation Equipment
-
Jinan Testing Equipment IE Corporation
DWCT Low Temperature Chamber for Impact Specimen in Drop Weight Testing is specially designed according to ASTM E 208& equivalent ISO Test Method for DWTT of Ferrite Steel Materials. The Low Temperature Chamber adopts multiple compressors, cooling technology and utilizes the heat balance principle and cycle stirring method to realize the constant cooling to impact specimen. With digital display and automatic control temperature, the Low Temperature Chamber is an ideal equipment for cooling and keeping constant temperature.
-
Product
Motor Control Resistors
-
Post Glover specializes in motor control resistors — the most popular use of our resistors — for severe duty applications. Our resistors make it possible to start and stop extremely powerful electric motors — such as those on cranes, compressors, and pumps — with safety and precision.
-
Product
Magnetostrictive Level Transmitters
-
ABB's K-TEK level products' patented sensor technology allows the LMT series transmitters to be used in the most challenging of industrial level applications such as interface measurement, compressor level and separator level applications. In addition, the LMT Series Level Transmitters are the only magnetostrictive level transmitters in the world to be certified for use in SIL2 and SIL3 systems per IEC61508.
-
Product
Enlarge Environmental Chamber
REXMED REC-250
-
MOD. REC-250, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Femtosecond Terawatt Ti:sapphire Laser System
MPA-XL
-
MPA-XL is a cost-effective terawatt Ti: sapphire amplifier system. It gives up to 200 mJ energy of the stretched pulse and further compression with 65% efficiency. A standard air compressor can be placed into a custom designed vacuum chamber.
-
Product
Environmental Chamber
REXMED REC-280
-
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Diaphragm Pressure Switch
CS & CD
-
Series CS and CD combine advanced design and precision construction in a small size. Unit is ideal for instrument panels, small compressors and general industrial applications. Visible set point and easy to wire SPDT snap switch reduce installation time. Operates in any position and is vibration resistant.
-
Product
Laboratory Incubators
DB & TE Series
-
These laboratory incubators have a wider range of temperatures. Also, these might be purchased if the role of the chamber might switch in future use – for example from cooler to above ambient temperatures. We have two types of heated and cooled incubators. The DB series incubators use compressor technology and have temperature ranges of 4°C-60°C. The TE series incubators use thermoelectric technology and have temperature ranges of 20°C-60°C.
-
Product
Marshall
-
Automatic Marshall compressor consisting of frame with wooden block, stable holding device for the mold set and hoisting device for the monkey. The drop weight is raised by a chain and an electric gear motor to the drop height of 457 mm.
-
Product
Megohm Meter
-
Digital Megohm Meter, model SMG5, is a compact standalone meter designed for checking HVAC compressor insulation. The SMG5 provides a 1000V voltage source, monitors current, and displays the resistance between the test points. Maximum current output is <1mA. It can be used to determine the condition of insulation from winding to ground in a motor, compressor, or transformer. Includes a case, alligator clip lead tip and leads with removable tips.
