-
Product
AC Power Source
61600 Series
-
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
Product
Test & Measurement Instrument Amplifiers
MPA-series
-
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
-
Product
Distance Measuring Equipment (DME)
MS 2002
-
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
Product
Drawing Die And Wire Measurement
Wire Diameter And Roundness Measurement
-
Optik Elektronik Gerätetechnik GmbH
The DGMS is a measuring system for diameter and roundness of wires, drawing dies and enameling dies. The wire diameter is measured highly accurate by an image processing system. To measure the roundness, an additional special holder is necessary to rotate the wire for the diameter measurement in several azimuths. The accuracy of the measurement is ‹1micron.
-
Product
Device Measurement EXpert (DMX)
S94601B
-
Device Measurement eXpert (DMX) is a measurement configuration assistant that aides users in setting up and optimizing complex measurements for various types of devices. The customizable wizard guides users through DUT connection, measurement setup, and display. DMX provides repeatability across the workflow by automatically setting up measurements in a consistent and optimal manner.
-
Product
Venturi Flow Measurement Trainer (UITM-22)
-
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
Product
Modular Measurement Equipment
-
Modular Measurement Equipment – These MCD measuring systems controlled by a PC offer a powerful measuring- and control unit in combination with our measurement software TestManager CE for all kinds of complex test systems.
-
Product
Dedicated Measuring Machine
-
We offer measurement systems optimized for various production sites. We design and manufacture high precision, stable specialized measuring instruments to match requested specifications and requested performance.
-
Product
Handheld Instruments for Measuring Humidity & Temperature
-
Our range of handheld instruments are perfect for monitoring environmental conditions. Models with an interchangeable probe input have the wide measurement ranges -100…200 °C, 0…100 %rh with a Rotronic probe selected for the application.
-
Product
Universal Measuring System
UMS4
-
Measuring device and data logger in oneAcoustic display of measured variablesBeep signal when limit value is exceededSerial interface for data transmissionConvenient data management with the DATA-UMS PC programDisplay and control through comfortable menu interface
-
Product
Scienlab Measurement And Control Module
SL1066B
Communications Module
The Measurement and Control Module SL1066B is a rack-mount measuring and control module that provides adjustable voltage outputs for BMS and DUT power supply and floating relay contacts to simulate e.g. vehicle specific terminals 15, 30 and 31.
-
Product
Dual Wavelength Multimode Light Source
FiberLink 6652
-
The Fiberlink 6652 Dual Wavelength Multimode Light Source is a cost effective, compact, handheld light source. The temperature compensated outputs are calibrated to couple -20dBm of optical power into multimode fiber.
-
Product
Measurements On The Same Device
How Many Item Family
-
Quanti - the functional measurement and electrical safety The tester of the product family is believed to be the first of its kind, as our devices allow users to perform electrical safety and functional measurements on the same device.
-
Product
Source Code Review
-
If code is legacy and massy and application is not performing well enough ,want to optimize your application internal structure.
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
Video Inspection Station with Measuring
VIS310
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
Noise Figure Measurements With Vector Correction
S97029B
-
The instrument’s standard receivers are used for noise figure measurements with the S97029B. An external preamplifier and filter(s) is required for devices with < 30 dB of excess noise (gain plus noise figure in dB)
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 High Temperature
-
A single-channel silicon-based thermopile that will withstand operating temperatures of 225C, with a small active area of 0.61mm x 0.61mm in a TO-5 package. The reduced height package functions as an internal aperture. Two thermistor options provide ambient package temperature measurement. Currently only available with 8-14um silicon window. Time constant of 18ms with Nitrogen encapsulation gas delivers a very low Temperature Coefficient of Responsivity of -0.4%C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
AC and DC Power Sources
CFS100 Series
-
The CFS100 Series programmable AC or DC output power sources are cost effective source of power for development, test and production applications requiring anywhere from 800VA or less to 4000VA of single phase AC or DC output.
-
Product
UV LED Light Source
Model 32
-
This new UV LED lightsource is designed and engineered by the proven lithography experts at OAI. The lightsource delivers a number of unique benefits, the most consequential of which is consistent intensity over an exceptionally long life. The lightsource is highly energy efficient, requires no maintenance or light replacement, and contains no mercury.
-
Product
RFID Evaluation Units
-
- Wide range of interfaces for RFID evaluation units- Robust antennas and ID tags with long writing / reading distance
-
Product
Measuring Systems For Beverage Can Manufacture
RICOS - Specialized Ring Contour Gauge For Drawing Dies
-
Optik Elektronik Gerätetechnik GmbH
Special designed for measurement of inside profile (land angles) of ironing dies for 2-piece beverage can manufacture, tolerance model and comparison with CAD data. Measuring task of RICOS is the measurement and evaluation of the inside profile of ironing rings in beverage can manufacture The measuring and evaluation system RICOS serve the profile measurement and the tolerance evaluation of ironing rings for beverage can manufacture.
-
Product
Storage Unit
DM-U.2
-
The DM-U.2 PXI Express Storage Unit provides up to 7.68TB of removable solid state storage (SSD) in a single PXI Express slot. It addresses the requirements of users who need to remove and replace PXI Express storage for security or other reasons. This includes data recording applications where recorded media must be quickly removed and replaced with fresh media between recording missions. It also facilitates easy data removal for data security reasons when a system is left unattended.
-
Product
Proving Units
-
Designed to suit a range of applications in the electrical contracting power utilities and industrial engineering sectors Seaward proving units are both self-powered and self-testing avoiding the need for a known supply point or bulky test equipment.
-
Product
Test & Measurement Automation Services
-
Our flexible and collaborative approach delivers efficient, accurate, and robust test systems, as well as the tools to leverage test data for effective results analysis. We develop systems using a variety of software and hardware platforms (custom and off-the-shelf), data acquisition systems, and control methods. We are comfortable developing custom turnkey systems or working alongside your team on your current system under development.
-
Product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
Measuring Systems For Beverage Can Manufacture
SPECIAL WORKBENCH
-
Optik Elektronik Gerätetechnik GmbH
To ensure the high measuring accuracy of RINGMASTER and PUNCHMASTER also under rough environmental conditions, a special workbench was developed. The workbench is equipped with vibration isolators, so that the equipment works also stable, if the toolroom is located close to the production line. Based on its ergonomics the special table ensures a fatigue free work.
-
Product
Process Control, Measurement and Inspection Workstation
ScanINSPECT VPI
-
ScanINSPECT VPI is a fully integrated, stand-alone process control, measurement and inspection and programming workstation for use in setting up processes before the production floor in the PCB or Hybrid Microcircuit assembly industries.
-
Product
Coating Thickness Measurement
-
The Calotest instruments from Anton Paar provide quick, simple and inexpensive determination of coating thicknesses. Employing the simple ball-cratering method, the thickness of any kind of single or multi-layered coating stack is accurately checked in a short time, in full compliance with relevant international standards.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
