-
Product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
-
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782253-01
-
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
IoT Ethernet I/O Modules
ADAM-6000/6200
-
Supporting Modbus & IoT protocols, Ethernet remote data acquisition modules offer analog, RTD, thermocouple, digital, relay and counter I/O.
-
Product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
-
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
-
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
PC/104-based Analog Input, Analog Output, and Digital I/O Board
PCM-MIO-A-1
-
The PCM-MIO-A-1 is a versatile, PC/104-based analog input, analog output, and digital I/O board designed for high-accuracy and high-channel-count analog and digital I/O. The board is based upon Linear Technology’s precision converters and voltage references which require no external calibration. The digital I/O utilizes WINSYSTEMS’ versatile WS16C48 Universal I/O controller functionality, also available on many of our SBCs and other I/O products.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782264-01
-
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-6115, 4 AI (12-Bit, 10 MS/s/ch), Buffer Size 16MS, 2 AO, 8 DIO, PXI Multifunction I/O Module
778194-01
-
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PXI Multifunction I/O Module - The PXI‑6115 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications where synchronization among analog input, analog output, and digital I/O is required, 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Digital I/O Vector Development Software
DIOEasy
-
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
Product
PXIe-6351, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO PXI Multifunction I/O Module
790593-01
-
The PXIe-6351 offers analog I/O, digital I/O, and four 32-bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6351 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Hybrid, Multifunction I/O
779639-01
-
32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-6374, 4 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, Multifunction I/O Device
785817-01
-
The PCIe‑6374 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6374 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included DAQExpress™ companion software provides basic measurement and analysis, while the NI‑DAQmx driver provides the ability to create customized automated measurement and control applications.
-
Product
96 Sink/Source
YAV90096
-
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Product
USB-6003, 8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782608-01
-
8 AI (16-Bit, 100 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6003 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6003 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB‑6003 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-7857, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786458-01
-
PCIe, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7857 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7857 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
PCI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, PCI Digital I/O Device
778792-01
-
The PCI-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up … states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PCI-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
2-Ch 24V HTL Incremental Encoder/Counter EtherCAT Slice IO Module
AMAX-5080
-
Channels: 2Counting Range: 32-bitMode: Counter (up/down, bidirection, up, A/B Phase)Signal Input: Logic level 0: 0 ~ 3 VDC, Logic level 1: 10 ~ 30 VDCInput Frequency: 5 Hz ~ 1 MHz max. (frequency mode), 1 MHz max. (counter mode)
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
-
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
2.4/5GHz Wi-Fi I/O Module With 4AI/4DI
WISE-4250-S214
-
Integrates 4 analog inputs (AI) and 4 digital inputs (DI) in a compact designAnalog Inputs support Burn-out Detection (4~20mA only) to prevent system failures and unplanned downtimeDigital inputs support High/Low value alarms, Latch, and Momentary Alarm modes for flexible event monitoringSupports 3kHz high-speed counter input (32-bit with 1-bit overflow) on digital input channelsComplies with IEEE 802.11ac (2.4GHz/5GHz) dual-band Wi-Fi for stable and high-speed wireless communicationEnsures secure data communication with WPA3/TLS 1.3 encryption and X.509 certificate authenticationEnables seamless cloud integration via MQTT and RESTful APIs, supporting direct data uploads to AWS, Azure, SCADA, and WebAccess platforms
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
-
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
-
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
-
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
PXI 32 Channel I/O, Low Side Driver
40-413-002
-
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
781439-01
-
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
781438-01
-
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785814-01
-
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
-
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
EMX-75XX
-
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
Product
PXIe-7915, KU060 FPGA, 4 GB DRAM, x8 Gen 3 PXI Coprocessor Module
785174-01
-
The PXIe-7915 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7915 KU060 FPGA is ideal for RF applications that require a substantial amount of signal processing.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782259-01
-
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
