Component
Testing of individual hardware or software components or groups of related components.
-
Product
Plugbord
4112
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side. Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
Product
RF COMPONENTS
-
If space is an issue and you are looking for high quality RF Components, ETL's wide range is designed and manufactured at the ETL factory. Covering DC to 40GHz, these are at the heart of many of our 19" Rack Systems.A key feature of many of ETL components is the ability to pass or block a 10 MHz signal or DC voltage through the products, which can be used to power interconnecting components or pass a stable frequency reference to a LNB or BUC within the system.
-
Product
PXI Vector Component Analyzer, 100 kHz to 53 GHz
M9818AS
Vector Component Analyzer
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
DC Power Supply
WPS Series
-
The WPS Series programmable DC power supply is a high-precision, wide range of voltage & current within the power rating of the power supply, full-featured high power density programmable DC Power Supplies. It can provide wide-range, low-ripple and stable DC output which is used for DC input products and components function testing and experimental simulation.
-
Product
PCI
-
PCI is a local computer bus for attaching hardware devices in a computer. PCI (Peripheral Component Interconnect) is part of the PCI Local Bus standard. The PCI bus supports the functions found on a processor bus but in a standardized format that is independent of any particular processor’s native bus.
-
Product
Hot Air Rework Station
21-10125
-
The 21-10125 is a hot air Rework Station provides a wide range of temperature and temperature settings for flexibility in soldering and desoldering work of sensitive components. A closed-loop heat sensor provides accurate and consistent working temperature. It features an intelligent cooling system cools the hand-piece with continued air movement after power has been switched OFF.
-
Product
Protocol Converter
MACC
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
Probe System for Life
PS4L
-
The Probe System for Life, or PS4L, is SemiProbe’s patented adaptive probe system architecture. Unlike traditional probe systems, all of the basics components of our systems, including the bases, stages, chucks, microscope mounts, and manipulators, are interchangeable, upgrade-able, and configurable. The PS4L Adaptive Architecture ensures and optimal test configuration for each individual customer application.
-
Product
Original VXI Module Shield Kits
11399x Series
-
* Clamshell design fits C-size modules with 96-pin connectors.* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Component side shield has an address switch opening and non-rectangular mounting hole pattern.* Complimentary layout support includes PCB design template and CAD layout files.* RECOMMENDED FOR LEGCY APPLICATIONS ONLY due to its non-rectangular hole pattern.
-
Product
Design and Development: Complete Systems and System Components
-
Custom Systems Integration Inc.
CSI''s design and development (D&D) organization has the resources, skill and experience to design a complete turnkey system, a system component or collaborate with customer''s internal staff on any part of a system.
-
Product
Produce Quality Meter
F-750
-
The F-750 Handheld Brix & Dry Matter Meter uses near-infrared (NIR) spectroscopy to estimate quality metrics such as dry matter, Total Soluble Solids (TSS or brix), titratable acidity, and color. Working like a high-powered flashlight, the F-750 sends particles of light into a commodity, then measures the NIR light interactance with molecular components inside of the commodity to quantify user-selected traits. The F-750 has a wide range of applications, from determining optimal harvest timing by assessing fruit maturity, to providing an objective analysis of produce quality of fruit in packing houses and upon import. The F-750 is a handheld, fully integrated system, allowing users to operate it out in the orchard or inside the QA lab. Its simple, intuitive user interface makes it easy for anyone to use, while its model building software makes it customizable and versatile.
-
Product
Five Channel Amplifier
-
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
Product
Reel-to-Reel Options
-
Designed for automated inspection of reels of components to check for component authenticity. Includes GTI-4000 software to compare lead frames, die size and wire bonds of each part to your known good part. The software will identify any part outside the tolerance and save an image of each part.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
Product
Software Communications Architecture (SCA) Development Environment
-
NordiaSoft products enable embedded systems developers to rapidly create software artifacts using the Component Based Development (CBD) and Model Driven Engineering (MDE) paradigms. Implementing the Software Communications Architecture (SCA), an open specification adopted internationally and evolved through the Wireless Innovation Forum (WInnF), a consortium of major radio manufacturers, academic, research laboratories and government authorities, the NordiaSoft products provide multiple advantages over other commercially available solutions for embedded systems:
-
Product
Hydraulic Component Test Stand
Model 700
-
Model 700 Hydraulic Component Test Stand (HCTS). Designed to test heavy-duty, off-highway, closed or open loop pumps, the 700 gives you the capacity to confidently and efficiently verify the quality of your work. Test new or rebuilt pumps, motors, valves, and cylinders independently, and communicate their quality to your customers with the help of PowerNet TD, data acquisition software for transmission and hydraulic systems. Convenient work height with adjustable mounting track. 100, 200 or 300 HP drive motor options available. Variable Frequency Drive (VFD) controlled drive motor. 200 gallon (757 L) high-mount hydraulic oil reservoir for flooded pump supply. Combined kidney filtration and cooling loop for continuous cleaning. Thermostatically controlled cooler and 7 kW reservoir immersion heater.
-
Product
Pin-Line™ Vertisocket™
Series 0517
-
Pin-Line Vertisockets. For mounting components, jumpers, etc., at right angle to PC board. Available 1 to 25 positions; cuttable to any number desired.
-
Product
Constant Flow Pump
Supercritical 24
-
The Supercritical 24 Constant Flow Pump is designed to be a reliable component wherever a constant flow must be maintained. The flow rate of the Supercritical 24 pump fitted with two standard 12 mL pump heads can be set in 0.01 mL/min increments from 0.00 to 24.0 mL/min.The Supercritical 24 Constant Pressure pump is designed to be a reliable component wherever a constant pressure must be maintained. Pressure can be set in 10-psi increments from 0 to 10,000 psi.
-
Product
ThermalBlade
-
This ATCA compatible design offers the flexibility to verify the power and thermal characteristics of your Advanced TCA chassis, logic cards and backplane designs. Emulating typical application component heights and features, airflow resistance and enclosure power dissipation can be evaluated and analyzed. A variety of power conditions can be selected and controlled independently to meet your design needs. Maximum sustainable watts are 450 with three switches turned on. Watts are dissipated throughout the entire ThermalBlade equally.
-
Product
PXIe-4112, 2-Channel, 60 V, 1 A PXI Programmable Power Supply
782857-01
Programmable Power Supply
The PXIe‑4112 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
Product
Safety Control Unit
SF-C21 Series
-
Panasonic Industrial Devices Sales Company of America
The safety control unit allows the user to connect and control various machine safety components. The SF-C10 series was specifically designed to connect and control Panasonic light curtains, while the SF-C21 safety control unit can be used for a variety of safety devices such as; safety switches, emergency switches, enable grip switches, safety beam sensors, safety scanners, and safety light curtains.
-
Product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
-
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Product
Semiconductor
-
Aerotech has a long history of engineering and manufacturing motion systems and components for high precision wafer processing, scanning electron microscopy (SEM), wafer bumping, 450 mm wafer manufacturing, lithography equipment and advanced laser micromachining. We also specialize in systems and components for vacuum applications, such as EUV lithography. So whether you need off-the-shelf wafer bumping components or a custom-engineered SEM system manufactured and tested to exacting specifications, Aerotech can provide the optimal solution for your application.
-
Product
Circbord
8029
-
VECTOR Electronics and Technology, Inc.
Pad-per hole pattern both sides. 0.042" diameter holes plated thru. 0.080" diameter isolated solder pad around each hole on both sides. 0.125" diameter corner mounting holes. Unrestricted component placement and extended area for high density applications..
-
Product
DWDM High Power DFB Buttterfly Laser
CA1782-XXX-XX-BT
-
The CA1782-XXX-XX-BT DWDM High Power DFB Buttterfly Laser component is characterized for use as a CW optical source in CATV and DWDM networks. The CA1782-XXX-XX-BT is dc-coupled with a built-in TEC, thermistor, and monitor photodiode. The device is mounted in a 14-pin, OC-48 pinout compatible butterfly package with the optical isolator mounted on the TEC. The CA1782-XXX-XX-BT incorporates a high efficiency coupling scheme to deliver 40 mW, 50 mW, 63 mW and 100 mW of CW optical power.
-
Product
Astronomy Solutions
-
For more than 40 years, Thales has delivered high accuracy optics for ground-based Astronomy all around the world. These optics range from single, but challenging, unmounted optical components up to fully integrated opto-mechanical systems. Our design heritage and past experience in this field cover the design, manufacture and AIT activities of many optics and sub-assemblies used in Telescope instrumentation, such as focal plane assemblies as well as the direct production of telescope mirrors themselves. Several major achievements of Thales ground-based Astronomy products were the Optical wide field corrector for the Dark Energy Survey (lien), the Reference Body for future Deformable Secondary Mirror of the VLT (lien) and different challenging spectrograph optics (Collimator and Cameras) for different Observatories (lien). One advantage Thales has with this activity is that most part of the manufacturing steps involved (i.e. opto-mechanical design, milling/grinding, lightening, polishing and coating) are directly under our control in our own facility. Our current capabilities for the production of optics for ground-based Astronomy are from a few centimeters size up to 2 meters. Thanks to the continuous efforts in R& D and investments into new production machines, Thales is now ready for future industrial challenges including the optical production of some key elements of the E-ELT, GMT and TMT programs.
-
Product
Isolators
-
This SMA coaxial isolator has a minimum isolation of 18 dB and a maximum input power of 10 Watts. PE8300 coaxial SMA isolator is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our radio frequency isolator can be bought and shipped worldwide the same-day as with Pasternack's other in-stock RF parts.Pasternack RF isolator PE8300 is part of our extensive in-stock RF, microwave and millimeter wave components available for purchase. This RF isolator is manufactured with SMA connectors that are female. Our SMA isolator has a minimum frequency of 1,000 MHz and a maximum frequency of 2 GHz.This SMA coaxial isolator has a minimum isolation of 18 dB and a maximum input power of 10 Watts. PE8300 coaxial SMA isolator is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our radio frequency isolator can be bought and shipped worldwide the same-day as with Pasternack's other in-stock RF parts.
-
Product
Versatile RF Network Analyzers for LF and MF
TE3000-series
-
The TE3000-series of RF vector network analyzers have full vector measurement capability, and accurately resolves the resistive, capacitive and inductive components of a load. The user can display the vector impedance plus a range of related parameters including SWR, reflection coefficient, return loss and R-L-C equivalent circuit.
-
Product
QE System
PVE300
-
The PVE300 system is a monolithic,turnkey solution for photovoltaic material and device characterization;a key component in research, or as part of a production-line quality process.
-
Product
Switching Regulators
-
Analog Devices offers a wide range of switching regulators that operate in step up (boost), step down (buck), and inverting modes. These devices are capable of generating a fixed or adjustable output voltage, and offer up to 2 A of output current. Some of the features available in ADI’s portfolio of switching regulators are low battery detector, user adjustable current limit, a variety of switching frequencies, and a reduced number of external components. This highly integrated, versatile family of products is intended to minimize external components for space challenged applications.
