TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
SX Range Broadband Power Amplifiers 0.8 GHZ - 6 GHZ
SX Series
-
Solid-state amplifier / Class A. Broadband (Dual-band): 0.8 GHz - 6 GHz. Typical output power:
-
Product
DP Range Broadband Power Amplifiers 10 kHz - 250 MHz
DP Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 250 MHzTypical output power : 1000 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB>600 W and H<-20 dBcAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Cabinet on wheels3 years standard warranty
-
Product
Measurement Power Amplifier
Qam
-
The amplifier is DSP controlled, with a very straightforward operation. Included is a white/pink noise signal generator. The internal signal module provides low crest noise signals to be able to reach high power levels from sound sources or electromagnetic shaker. External input of signal is equally possible, with spectral linearisation or without. This can be used for music, RASTI or any other signal
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
GaN 100W Power Amplifiers
PE15A5033F
-
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
Product
LINEAR AMPLIFIERS
F-series
-
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
Product
Broadband Power Amplifiers
-
Our range of broadband power amplifiers are designed using the most suitable devices and techniques. We don’t believe in following fashion in our choice of parts, but will continue to use older technology where it is still the best, and incorporate the new where improvements can be made.
-
Product
Erbium Doped Amplifier
CATV
-
Amonics CATY Rackmount EDFA area made with high power pump laser and stability pump combiners, robust in high power boosting. The result are EDFAs that possess high output power, high gain with very low noise, and are ideal for CATV applications. The turnkey microprocessor controlled rackmount EDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
Super Low Noise Amplifiers
WCA Series
-
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
Product
High Voltage Amplifier
HA-205
-
*2500V/uS Super High Speed Model *170Vp-p (±85V DC) *900mAp-p (±450mA DC) *Bandwidth: 3MHz / 100Vp-p *Gain (AMPL): 0~35 (10 Turn VR+SW) *Microprocess Control Protection
-
Product
Saluki SE1022 DSP Lock-In Amplifier
-
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
-
Product
Power Amplifiers
-
Applied Research and Technolgy
Drive studio monitors or installation speakers in any environment.
-
Product
Semiconductor Optical Amplifiers
-
A Semiconductor Optical Amplifier (SOA) is essentially a laser diode (LD) with no feedback from its input and output ports and hence is also referred to as a Traveling-Wave Amplifier (TWA). Semiconductor Optical Amplifiers (SOAs) have proven to be versatile and multifunctional devices that are key building blocks for optical networks.
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
System Amplifier
-
Solid state Broadband Amplifiers are designed for optimum operation for IED Jammer Applications which is featured as below. We can rack mount any of our existing amplifiers or systems or custom design the amplifier and enclosure. Each Rack Mounted Amplifiers are built around a large bonded fit heat-sink rated for high temperature ambient operation.
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Testing)
PA60Bi
-
PA60Bi is the panel-mounted power amplifier, which can produce 3-phase current, with maximum RMS phase current of 60A and maximum output power of 800VA, and 4-phase voltage, with maximum RMS phase voltage of 120V and maximum output power of 60VA.
-
Product
Composite 2×12 Video Distribution Amplifier
VDA212RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
4 Channel Variable Gain Fast Amplifier
V974
-
The Mod. V974 is a 4 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a voltage gain adjustable from 1 to 10 in x1 steps. Channels are non-inverting and bipolar: they amplify both positive and negative signals.
-
Product
Portable Power Amplifier
PAC60Cip
-
PAC60Cip is the portable conventional linear power amplifier model with six channels of current output. It is with 6*30A/210VA output, and this current amplifier is similar to PAC60Ci but it has lower output power and less weight.
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
Product
Converter Signal Amplifier – 0…10 Vdc – Wall Mounting
HD978TR6
-
Configurable converter signal amplifier with 0…10 Vdc (10…0 Vdc). Input measuring range -10 ..+60 mVdc. Standard configuration 0…20 mVdc. Minimum measuring range 2 mVdc.
-
Product
3-5 Watt Power Amplifiers
CCM1095 and CCM2096
-
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
Product
2 Channel Microphone Power Supply and Conditioning Amplifier
SoundConnect 2 mic power supply
-
SoundConnect 2 is a rugged 2-channel USB controlled microphone power supply and conditioning amplifier.
-
Product
Microwave Power Amplifier 1/4 Watt 10 MHz to 50 GHz
GT-1051B
-
The Spanawave/Giga-tronics GT-1051B Microwave Power Amplifier offers linear high-power amplification across muultioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
Product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
-
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
