TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
-
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
Product
DT Range Broadband Power Amplifiers 10 KHZ - 1000 MHZ
DT Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 1000 MHzTypical output power : 25 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 20 W and H<-20 dBc up to 450 MHz andP1dB > 10 W and H<-20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
Broadband Power Amplifier
PAS-08025-30
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 48.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
High-Speed System Synchronization and Distribution Amplifier - 3U VPX
Model 5903
-
- Multi-board synchronization with Quartz RFSoC video- Synchronizes up to 64 channels across eight Quartz® boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
RF Amplifier
SA831
-
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
CATV Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
Product
Narrowband RF/Microwave Power Amplifier
-
While our broadband amplifier series are designed for multi-purpose, narrowband amplifier series may provide more appropriate solution for your specific needs. By narrowing the frequency range, smaller, lighter amplifier solution at more reasonable cost will be usually available.
-
Product
Automotive Audio Power Amplifiers
-
ST is the recognized leader in automotive power amplifiers. Our car audio amplifiers provide the traditional clean and powerful sound that users have come to expect, as well as all the protection and safety features needed to make our devices robust in an automotive environment.
-
Product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
-
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
Product
2 GHz to 6 GHz, 45 dBm Power Amplifier
HMC7885
-
The HMC7885 is a 32 W gallium nitride (GaN), monolithic microwave integrated circuit (MMIC) power amplifier (PA) module that operates between 2 GHz and 6 GHz, and is provided in an 18-lead hermetically sealed module. The amplifier typically provides 21 dB of small signal gain and 45 dBm of saturated radio frequency (RF) output power. The amplifier draws 2200 mA of quiescent current (IDD) from a 28 V dc supply. The RF input and output are dc blocked and matched to 50 Ω for ease of use.
-
Product
Amplifiers
-
Commercial grade indoor distribution amplifier, 54-870 MHz forward gain of 30 dB, 5-42 MHz reverse gain of 20 dB, forward path slope and gain controls with separate reverse path gain control
-
Product
Current Feedback Op Amplifiers
-
Analog Devices high speed (> 50 MHz) current feedback op amps enable you to operate at higher speeds. Current feedback op amps traditionally have wider bandwidths and higher slew rates than voltage feedback amplifiers and do not feature a gain bandwidth restriction associated with voltage feedback op amps.
-
Product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
-
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
Product
40~860 MHz Trunk Hybrid Amplifier
AS 1616
-
Hybrid Amplifiers used in Trunk and branch lines specially designed to serve the needs of cable systems with very Long Trunk Cables. They are in Aluminium Housing providing maximum heat dissipation and have RFI Shielding. They incorporate superior quality Hybrid IC Module to obtain excellent features.- Frequency Range: 40 ~ 860 MHz- Mains cum Power Pass- Output Level: 102 dBµV- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Optimum for Trunk Distribution- Superior Quality Hybrid IC Module- Hybrid IC Protected- Voltage Selection LED - for Easy Selection
-
Product
Femtosecond Optical Parametric Amplifier
CDP 2017
-
*> 30% conversion efficiency from pump pulse to parametric radiation*Wavelength conversion for ExciPro, TAPPIR, FOG 100-DA*Wavelength conversion options for wavelength tuning from 240 nm to 16 mm
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
Low-Noise Amplifiers
-
Broadband, narrowband, high-frequency, our extensive portfolio of LNAs is ready to tackle the toughest requirements. Don’t see exactly what you need? We have a vast library of pre-engineered building blocks ready to support any custom design.
-
Product
Saluki SE1022D DSP Lock-In Amplifier (Dual-channel)
-
SE1022D Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. More importantly, SE1022D has dual independent input channels and dual independent high precision signal generators. Each input channel and signal generator can be used independently which means that the SE1022D is equivalent to two traditional lock-in amplifiers. Moreover, due to the twin symmetrical design, the two independent input channels and signal generators have ultra-high synchronicity, which meets the measurement requirements demanding extremely high synchronization.
-
Product
Portable Power Amplifier
PA30Bip
-
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
Dual Relay Trip Amplifier for RTD and Slidewire Sensors
SEM1633
-
The SEM1633 provides an accurate alarm / switching function when used with RTD or Slidewire sensors. Other sensor characteristics or your own 22 point linearization characteristic (for slidewire or linear resistance) can be downloaded into the product enabling you to adapt it exactly to your application.
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
